Dometic WeatherPro Installation Instructions Manual

Dometic WeatherPro Installation Instructions Manual

Power awning
Hide thumbs Also See for WeatherPro:

Advertisement

USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
CANADA
Dometic Corporation
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA
SERVICE CENTER &
DEALER LOCATIONS
Please Visit:
www.eDometic.com
INSTALLATION
INSTRUCTIONS
REVISION A
Form No. 3309523.052 10/16
©2016 Dometic Corporation
LaGrange, IN 46761
WeatherPro Hardware
8551201.400(X) Basement Hardware
8551202.400(X) Standard Hardware
8551203.400(X) 5th Wheel Basement Hardware
8551204.400(X) 5th Wheel Standard Hardware
This manual must be read and
understood before installation,
adjustment, service, or mainte-
nance is performed. This unit must
be installed by a qualified service
technician. Modification of this
product can be extremely hazard-
ous and could result in personal
injury or property damage.
Important:
stay with unit. Owner read carefully.
FOR
905(XX)(XX.XX)(X)(X)
8(X)5(XX)(XX.XX)(X)(X)
Fabric Roller Tube Assembly
Lire et comprendre ce manuel avant
de procéder à l'installation, à des ré-
glages, de l'entretien ou des répara-
tions. L'installation de cet appareil doit
être effectuée par un réparateur quali-
fié. Toute modification de cet appareil
peut être extrêmement dangereuse et
entraîner des blessures ou dommages
matériels.
905(XX)(XX.XX)(X)(X)FRTA
8(X)5(XX)(XX.XX)(X)(X)FRTA
These instructions must
RECORD THIS UNIT INFORMATION FOR
FUTURE REFERENCE:
Model Number
Serial Number
Date Purchased
MODEL
855120(X).400(X)
Hardware

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WeatherPro and is the answer not in the manual?

Questions and answers

Summary of Contents for Dometic WeatherPro

  • Page 1 RECORD THIS UNIT INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Date Purchased WeatherPro Hardware 8551201.400(X) Basement Hardware 8551202.400(X) Standard Hardware 8551203.400(X) 5th Wheel Basement Hardware 8551204.400(X) 5th Wheel Standard Hardware SERVICE OFFICE Dometic Corporation 1120 North Main Street 905(XX)(XX.XX)(X)(X) Elkhart, IN 46514 8(X)5(XX)(XX.XX)(X)(X)
  • Page 2: Safety Instructions

    855120(X).400(X) WeatherPro Hardware Installation Instructions SAFETY INSTRUCTIONS REQUIRED PARTS (Packed with each Hardware Assembly) 8551201.400(X) & 8551202.400(X) Hardware This manual has safety information and instruc- (2) - Top Mounting Bracket Cover tions to help users eliminate or reduce the risk (2) - Bottom Bracket Cover of accidents and injuries.
  • Page 3: Specification Chart

    Insure sufficient room is available before starting installation. If a slide 1-3/4" 1-3/4" 1-3/4" 1-3/4" out room is under the canopy, contact your Dometic 5/8" 5/8" 13/32" 13/32" Sales Representative. A = Overall length of hardware.
  • Page 4 855120(X).400(X) WeatherPro Hardware Installation Instructions FIG. 2 FIG. 3 8551203.400(X) 5th Wheel Basement Hardware 8551201.400(X) Basement Hardware Top Mounting Bracket Top Mounting Bracket Back Channel Front Channel Front Channel E - F Back Channel Back Channel Hole For Cables Front Channel...
  • Page 5: Installation Instructions

    Note: One hardware arm assembly has a rainshed bottom arm. This arm goes on the left side of FRTA. See FIG. 6. Installation of Dometic Corporation awnings will briefly re- (Hardware shown in open position for clarity) quire three people. Use the following procedure to assure 3.
  • Page 6 These 3308059.XXX(X) and 3309390.XXX(X) back chan- Important: Keep the two arm assemblies parallel to nel spacer kits can be obtained through Dometic. each other to avoid excessive twisting and possible b. Place both top brackets in position over or damage to the assembly.
  • Page 7 These 3308059.XXX(X) and 3309390.XXX(X) back chan- • Next, plug the factory pre-wired wind nel spacer kits can be obtained through Dometic. sensor harness in the front channel into Top bracket must be installed parallel with the wind sensor. Make sure it is pushed the awning rail.
  • Page 8: Wire Length

    The installer will provide a wire harness using installing a Dometic Corporation Oasis Elite awning. the proper plugs and sockets or the supplied Unless a Dometic Corporation Oasis Elite awning is 3309726.036 Wind Sensor Wire Harness, being installed at the same time only connectors des- depending on the kit being installed.
  • Page 9 855120(X).400(X) WeatherPro Hardware Installation Instructions d. Route three (3) wires (installer supplied) from 3. If the control box is not operational (all LEDs on the Electronic Control to the remote switch. the front of the control box are off) even after...
  • Page 10 855120(X).400(X) WeatherPro Hardware Installation Instructions 5. Secure back channel to wall with two (2) 3/16" x FIG. 13 1" Oscar rivets provided. See FIG. 12. Important: Structural backing (metal) is required where oscar rivets will be installed through RV side wall for securing back channel.
  • Page 11 855120(X).400(X) WeatherPro Hardware Installation Instructions 3311917.011 & 3311917.029 Control Kit Wiring FIG. 14 Socket (18-24 gauge) Pin (14-20 gauge) Pin (14-20 gauge 350689-1 350547-1 350547-1 Plug Plug Plug 350766-1 350777-1 350777-1 Plug Plug Plug Plug Plug Plug 350766-1 350766-1 350766-1...

Table of Contents

Save PDF