Xylem YSI ProOBOD User Manual
  1. Manuals
  2. Brands
  3. Xylem Manuals
  4. Accessories
  5. YSI ProOBOD
  6. User manual

Xylem YSI ProOBOD User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ProOBOD
IDS ProOBOD
U S ER MAN UAL
Documen t # 626471

Advertisement

Table of Contents
loading

Related Manuals for Xylem YSI ProOBOD

Summary of Contents for Xylem YSI ProOBOD

  • Page 1 U S ER MAN UAL Documen t # 626471 ProOBOD IDS ProOBOD...

  • Page 2: Table Of Contents

    C O N T E N T S Warranty ....................i Introduction ..................1 Getting Started ..................2 Unpacking the OBOD Probe ..........3 OBOD Probe Operation ..............4 Powering the Stirrer ...............4 Calibration - Dissolved Oxygen ..........4 Temperature ................5 Taking Measurements ............5 Maintenance and Storage ..............5 Updating Instrument and Probe Firmware ......6 Sensor Maintenance - Dissolved Oxygen ......6 Sensor Maintenance - Temperature ........8...

  • Page 3: Warranty

    W A R R A N T Y ® The YSI ProOBOD and IDS ProOBOD probe and cable assemblies are warranted for two (2) years from date of purchase by the end user against defects in materials and workmanship, exclusive of batteries and any damage caused by defective batteries.

  • Page 4: Introduction

    I N T R O D U C T I O N Thank you for purchasing a YSI Optical Biochemical Oxygen Demand probe (ProOBOD® or IDS ProOBOD). The ProOBOD is designed for use with a YSI ProODO® instrument. The IDS ProOBOD is designed for use with a YSI MultiLab IDS instrument.

  • Page 5: Getting Started

    Unpacking the OBOD prOBe oxygen levels, and the elimination of frequent membrane/electrolyte changes and electrode servicing. Each OBOD probe and replacement OBOD sensor cap For more information on the ProODO and MultiLab IDS instruments, includes an instruction sheet with important information including product specification, please visit ysi.com or contact YSI unique and specific to each individual cap.

  • Page 6: Obod Probe Operation

    O B O D P R O B E O P E R A T I O N instrument may hold its calibration for many months. however, for the highest data accuracy, YSI recommends verifying the instrument’s calibration on a daily basis. To verify the instrument’s calibration, place Connect the OBOD probe to the instrument.

  • Page 7: Updating Instrument And Probe Firmware

    UpDating inStrUment anD prOBe Firmware humid environment. Therefore, the OBOD sensor should be stored in either a BOD bottle that contains a small amount of clean water The instrument and probe firmware can be updated via ysi.com. There (approximately 40 ml) or in a BOD bottle that is filled with clean water you will find the new firmware files and instructions on how to update so the sensor cap is immersed in water, see Sensor Storage for more the instrument and/or probe.

  • Page 8: Sensor Maintenance - Temperature

    SenSOr StOrage 6. Locate the o-ring lubricant included with the new sensor cap. Apply a thin coat of o-ring lubricant to the installed o-ring. After ShORT-TERM STORAGE application, there should be a thin coat of o-ring lubricant on the o-ring only. Remove any excess o-ring lubricant from the o-ring When the OBOD is not in use, it must be stored in a moist environment, and/or probe with a lens tissue.

  • Page 9: Error/Status Messages

    If the DO% measurement is incorrect in a water-saturated air After reinstalling the sensor cap, perform a calibration and then environment (BOD bottle with 40 ml of clean water) after calibration, reevaluate the quality of the dissolved oxygen measurements. If ensure the instrument’s barometer reading is correct by comparing it problems persist, try rehydrating or replacing the sensor cap.

  • Page 10: Accessories / Parts List

    D E C L A R A T I O N O F C O N F O R M I T Y Temperature Range -5 to 50°C We declare under our sole responsibility that the listed product conforms Accuracy ±...

  • Page 11: Recycling

    R E C Y C L I N G Service inFOrmatiOn YSI has authorized service centers throughout the United States and YSI is committed to reducing the environmental footprint in the course Internationally. For the nearest service center information, please visit of doing business.

  • Page 12: Appendix A - Do% Calibration Values

    Pressure Altitude Calibration A P P E N D I X A - D O % C A L I B R A T I O N value V A L U E S Inches Hg mm Hg mbar Feet Meters % Saturation 22.14...

  • Page 13: Drawing # A626471

    Item # 626471 Rev C Drawing # 626471 April 2013 ©2013 YSI Incorporated...

This manual is also suitable for:

Ysi ids proobod

Table of Contents