GE C2K Hardware Reference Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Motherboard
  5. C2K
  6. Hardware reference manual
GE C2K Hardware Reference Manual

GE C2K Hardware Reference Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
GE C2K Hardware Reference Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C2K and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for GE C2K

Summary of Contents for GE C2K

  • Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
  • Page 2 Intelligent Platforms Hardware Reference C2K* 6U CPCI Single Board Computer Publication No: 70000524-800 Rev. C Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 3 Document History Hardware Reference Document Number: 70000524-800 Rev. C September 30, 2011 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 4: Table Of Contents

    Table of Contents Chapter 1: Introduction Overview .......................... 1-1 Specifications ........................1-3 Compliance ........................1-4 C2K GPIO DC Electrical Characteristics ................. 1-4 Block Diagram ......................... 1-5 Technical Support ......................1-7 Related Documents ......................1-7 Chapter 2: Installation What Is Included ......................2-1 Equipment Needed ......................
  • Page 5 4.17.1 PMC0 Site Features ................... 4-14 4.17.2 PMC1 Site Features ................... 4-15 4.18 Temperature Sensor ...................... 4-15 4.19 Interrupt Circuitry ......................4-15 4.20 EEPROMS ........................4-16 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 6 USART Registers ....................5-45 5.2.6 Standard USART Registers ................5-46 5.2.7 USART Divisor Latch Registers ................. 5-53 Component Locations ....................5-54 Chapter 6: Transition Module C2K-TM Overview .......................... 6-1 Physical Description ......................6-2 Block Diagram ........................6-3 Connector Pin Assignments ..................... 6-4 6.4.1 CompactPCI Connectors ..................
  • Page 7 C2K Block diagram (a) ......................1-5 Figure 1-2 C2K Block diagram (b) ......................1-6 Figure 2-1 C2K (C-style) with PMC modules installed ................. 2-5 Figure 2-2 C2K (N-style) with PMC modules installed ................. 2-6 Figure 3-1 Front panels: a. C-style; b. N-style..................3-1 Figure 3-2 Connector locations (C-style)....................
  • Page 8 List of Tables Table 1-1 C2K GPIO DC Electrical Characteristics................1-4 Table 3-1 cPCI connector J1 pin assignments ..................3-4 Table 3-2 CompactPCI connector J2 pin assignments ................3-5 Table 3-3 CompactPCI connector J3 pin assignments ................3-6 Table 3-4 cPCI connector J4 pin assignments ..................3-7 Table 3-5 CompactPCI connector J5 pin assignments ................3-8...
  • Page 9 Table 6-12 GPIO on-board header (P2) pin assignments ..............6-10 Table 6-13 JTAG header (P18) pin assignments .................6-11 Table 6-14 PMC0_P11 and PMC1_P12 pin assignments..............6-12 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 10: Chapter 1: Introduction

    Chapter 1: Introduction 1.1 Overview The C2K* is a 6U PICMG 2.16 compatible Single Board Computer intended for both system con- troller and peripheral slot applications. The board provides a CPU core, PICMG 2.16 compatible backplane interface, and several peripheral devices/interfaces. The CPU core circuitry consists of ®...
  • Page 11 Introduction C2K Transition Module GEIP offers an optional C2K Transition Module (C2K-TM) with the following on-board and rear-panel connections: • BATT+ (P13)—on-board 2 x 5 connector • ETH0 (J6)—rear-panel RJ-45 connector • ETH1 (J7)—rear-panel RJ-45 connector • ETH2 (J8)—rear-panel RJ-45 connector •...

  • Page 12: Specifications

    C-style: 0.04g2 / Hz @ 5-100Hz (2g rms), 60 min. / axis N-style: 0.1g2 / Hz @ 5-2000Hz (12g rms), 60 min. / axis C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 13: Compliance

    Calculations are available in accordance with MIL-HDBK-217. Please contact GEIP for latest values. Safety Designed to meet standard UL1950/60950 Emissions Designed to meet FCC Part15, SubPart A 1.4 C2K GPIO DC Electrical Characteristics C2K GPIO DC Electrical Characteristics Table 1-1 Symbol Parameter Unit...

  • Page 14: Block Diagram

    USB3 Controller User EEPROM SATA1 GD31244 SATA SATA2 Controller Flash FPGA 8051 IPMC (soldered) Swap Device Bus Ctlr C2K Block diagram (a) Figure 1-1 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 15: Figure 1-2 C2K Block Diagram (B)

    COM1 (RS-422) UART0 RS-422 I/F COM1 (RS-232) RS-232 I/F MPSC COM2 (RS-422) UART1 RS-422 I/F COM2 (RS-232) RS-232 I/F C2K Block diagram (b) Figure 1-2 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 16: Technical Support

    Most issues can be resolved by referring to this manual. If any problems cannot be resolved, please contact GEIP Technical Support: If products must be returned, contact GE for a Return Material Authorization (RMA) Number. This RMA Number must be obtained prior to any return.
  • Page 17 • PICMG 2.3 Rev 1.0—PMC on CompactPCI Specification, August, 1998. • PICMG 2.9 Rev 1.0—CompactPCI System Management Specification, February, 2000. • PCI Special Interest Group—PCI Local Bus Specification, Revision 2.3, October 2001. C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 18 2. VITA Specifications are available to VITA members only. GEIP is not authorized to distribute copies of these specifications. More information can be found at http://www.vita.com. 3. Data sheets from hardware components can be downloaded from individual vendors web sites. C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 19: Chapter 2: Installation

    Chapter 2: Installation 2.1 What Is Included The C2K Single Board Computer (SBC) is shipped with the following items: • C2K SBC Printed Circuit Assembly 2.2 Equipment Needed The following items are needed to install and operate the C2K: • C-style CompactPCI-compatible chassis •...

  • Page 20: Power Requirements

    ROM. 2.4.2 EM_BOOTSEL# (P7) P7 is a 2-pin Emergency Boot Select header/jumper that determines which boot code the C2K will execute after reset. Boot code provided by GEIP is stored in the upper 8MB of flash memory. If a jumper is installed on the EM_BOOTSEL header (P7), the GEIP firmware will boot from the GEIP provided emergency boot code stored in the Emergency Boot area of flash.

  • Page 21: Cop_En (P10)

    Caution! Do not attempt to install the C2K in a Fabric slot of a PICMG 2.16 Packet Switching Backplane. The C2K is equipped with an IEC key to prevent such installation, but if the backplane is not keyed installation is still possible.

  • Page 22: C2K N-Style Installation

    NOTE: The C-style C2K is Hot Swap-compliant and can be installed in and removed from a powered-on Hot Swap-compliant chassis. After sliding the C2K in the slot guide until the card engages the pins, wait for the blue front-panel Hot Swap LED to turn off before closing the ejector handle switch (bottom ejector handle).

  • Page 23: Figure 2-1 C2K (C-Style) With Pmc Modules Installed

    Installation PMC Module PMC Module C2K (C-style) with PMC modules installed Figure 2-1 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 24: Figure 2-2 C2K (N-Style) With Pmc Modules Installed

    Installation PMC Module PMC Module C2K (N-style) with PMC modules installed Figure 2-2 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 25: U-Boot Utility

    Installation 2.6 U-Boot Utility The C2K includes a universal boot loader (U-Boot) utility that is pre-installed in flash ROM. ® U-Boot is designed to work with any operating system including Linux and VxWorks and per- forms the following functions: • Load the O/S kernel from Ethernet, user flash area, or USB •...
  • Page 26 TFTP protocol tfpboot version prints monitor version C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 27: Information Commands

    Installation 2.6.4 Information Commands The following U-Boot commands provide information bdinfo C2K=> help bdinfo bdinfo: prints board information used by U-Boot, such as memory addresses and sizes, clock frequencies and MAC addresses. coninfo C2K=> help coninfo cp [.b, .w, .l] source target count: displays console I/O device information.

  • Page 28: Memory Commands

    Installation 2.6.5 Memory Commands base C2K=> help base base: prints address offset from memory commands. base off: sets address offset for memory commands to ‘off’. crc32 C2K=> help crd32 crc32 address count [addr]: calculates CRC32 checksum [save at addr]. C2K=> help cmp cmp [.b, .w, .l] adder1 addr2 count:...

  • Page 29: Flash Memory Commands

    Installation C2K=> help mw mw [.b, .w, .l] address value [count]: perform memory write. C2K=> help nm nm [.b, .w, .l] address: modifies memory, read and keep address. loop C2K=> help loop loop [.b, .w, .l] address number_of_objects: performs loop on a set of addresses.

  • Page 30: Execution Control Commands

    2.6.7 Execution Control Commands boot C2K=> help boot bootm C2K=> help bootm bootm [addr [arg...]]: boots application image stored in memory passing argument ‘arg ...’; when booting a Linux kernel, ‘arg’...

  • Page 31: Environment Variables Commands

    Installation loadb C2K=> help loadb loadb [off] [baud]: loads binary file over serial line with offset ‘off’ and baud rate ‘baud’. loads C2K=> help loads loads [off] [baud]: loads S-Record fileover serial line with offset ‘off’ and baud rate ‘baud’.

  • Page 32: Miscellaneous Commands

    Installation C2K=> help run run var [...]: runs the commands in the environment variable(s) ‘var’. bootd C2K=> help bootd bootd: no help available 2.6.10 Miscellaneous Commands ping C2K=> help ping ping pingaddress: date C2K=> help date date [MMDDhhmm [CC]YY][.ss]: date reset: without arguments: prints data and time.

  • Page 33: Chapter 3: Interfaces

    Chapter 3: Interfaces 3.1 Front Panel The C2K front-panel (C-style version only) includes the following features: • LEDs RESET • Two PMC front panel cutouts • USB connector (J8) PMC1 PMC1 • Recessed manual reset switch Hot Swap (blue), PWR (green), PBIT LEDs: (green), and User (yellow), 8051 (yellow).

  • Page 34: Connectors

    (Drawing not to scale) Connector locations (C-style) Figure 3-2 NOTE: The front-panel USB connector (J8) is only available on C-style versions of the C2K. C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 35: Figure 3-3 Connector Locations (N-Style)

    Interfaces Connector locations (N-style) Figure 3-3 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 36: Compactpci Connector Pin Assignments

    REQ0# PCI_PRESENT# +3.3V CLK0 AD31 J1-5 BRSVP1A5 BRSVP1B5 PCI_RST# GNT0# J1-4 IPMB_PWR HEALTHY# INTP INTS J1-3 INTA# INTB# INTC# INTD# J1-2 J1-1 -12V TRST# C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 37: Table 3-2 Compactpci Connector J2 Pin Assignments

    GNT2# REQ3# J2-1 CLK1 REQ1# GNT1# REQ2# NOTES: SMB_SCL: This signal is not supported on C2K. SMB_SDA: This signal is not supported on C2K. C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 38 PMC0_J14 per PICMG 2.3 (PMC0_1–64) PMC0_VIO: +3.3V or +5V according PMC0 VIO Selection header/jumper—P12 J3-C-14 is connected to +3.3V on Rev.10 and Rev. 20 level boards. C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 39: Table 3-4 Cpci Connector J4 Pin Assignments

    ETH2_DB+ ETH2_DB- ETH2_DD+ ETH2_DD- NOTES: ETHn: Gigabit Ethernet (ETH2) GPIO: General purpose I/O (GPIO_0–GPIO_3) Serial I/O: COM1, COM2 (RS-422), COM3, COM4 (RS232/422), COM5–COM8 (RS-422/485) C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 40 GPIO_15 or Non-Maskable Interrupt input. To make this signal non-maskable, the CPU_MRS[EE] interrupt mask bit, as well as the bridge mask, must be set. PB_RST_IN#: Push-button reset button signal from backplane (C2K-TM). PMC1 I/O: from PMC1_J24 per PICMG 2.3 C2K User’s Guide...
  • Page 41 1.5Gb/s serial ATA (SATA1, SATA2). Serial I/O: These ports are configured as RS-232 (transmit and receive signals only) (COM1, COM2) Standard USB 2.0 ports (USB1, USB2, USB3) C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 42: Pmc Connector Pin Assignments

    PCI0_AD0 PCI0_ACK64# +3.3V PCI0_REQ64# rsvd NOTES: BUSMODE1#: C2K ignores this signal. BUSMODE2–4#: Wired to indicate “Return ‘Card Present’ if PCI capable and uses PCI Protocol” mode, as defined in IEEE 1386-2001. 3.3Vaux: Not connected on C2K. C2K User’s Guide 3-10...

  • Page 43: Table 3-7 Pmc0_J13 And Pmc0_J14 Pin Assignments

    PMC0_49 PMC0_51 PCI0_AD36 PMC0_51 PMC0_52 PCI0_AD35 PCI0_AD34 PMC0_53 PMC0_54 PCI0_AD33 PMC0_55 PMC0_56 PCI0_AD32 PMC0_57 PMC0_58 rsvd PMC0_59 PMC0_60 PMC0_61 PMC0_62 rsvd PMC0_63 PMC0_64 3-11 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 44: Table 3-8 Pmc1_J21 And Pmc1_J22 Pin Assignments

    PCI1_AD0 PCI0_ACK64# +3.3V PCI0_REQ64# rsvd NOTES: BUSMODE1#: C2K ignores this signal. BUSMODE2–4#: Wired to indicate “Return ‘Card Present’ if PCI capable and uses PCI Protocol” mode, as defined in IEEE 1386-2001. 3.3Vaux: Not connected on C2K. C2K User’s Guide 3-12...

  • Page 45: Table 3-9 Pmc1_J23 And Pmc1_J24 Pin Assignments

    PCI1_AD36 PMC1_51 PMC1_52 PCI1_AD35 PCI1_AD34 PMC1_53 PMC1_54 PCI1_AD33 PMC1_55 PMC1_56 PCI1_AD32 PMC1_57 PMC1_58 rsvd rsvd PMC1_59 PMC1_60 rsvd PMC1_61 PMC1_62 rsvd PMC1_63 PMC1_64 3-13 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 46: Cop Port (J6) Pin Assignments

    Interfaces 3.2.4 COP Port (J6) Pin Assignments The C2K includes an on-board 2 x 10-pin COP Port header (J6) for stepping through code at the MPC7448 processor. The VDD_SENSE signal is fixed at +2.5V. Table 3-10 shows the COP Port pin assignments.

  • Page 47: Front-Panel Usb (Usb4) Connector (J8) Pin Assignments

    3.2.7 Serial I/O COM Port Termination Header (P15) Pin Assignments The C2K provides a 2 x 8-pin header (P15) for enabling line terminations for COM5–COM8 RS-422/485 ports. Line termination for a port is enabled when a jumper is installed across the cor- responding pins shown in Table 3-13.

  • Page 48: Front-Panel Leds

    Interfaces 3.3 Front-panel LEDs The C2K provides the following indicator LEDs on the front panel: Color Function indication Green Illuminates when the internal power rails are within specification. De-illuminates when internal power rails are out of specification. PBIT Green Illuminates when the processor has completed its built-in test diagnostics. De-illumi- nates if the built-in test diagnostic tests fail, either during the initial power-up or reset diagnostics, or during continual background diagnostics.

  • Page 49: Chapter 4: Functional Blocks

    4.2 DDR SDRAM The C2K provides system memory in configurations of 512MB on the standard build, or 256MB, or 1GB densities available as build options. The DDR SDRAM is organized in a memory array of one bank (256MB/512MB) or two banks (1GB) of devices.
  • Page 50 This is not a user-configurable option. External Write-Protect The C2K provides a ROM_WP# pin at the backplane (cPCI_J5 A8) to allow an external mechanism to enable global write-protection. If the ROM_WP# signal is asserted (active low), all write/erase functions are disabled.

  • Page 51: Boot Code Selection

    Selection of which boot code is used to boot the C2K is controlled through the EM_BOOT_SEL bit (bit 6) in the FPGA Status Register (see “Status Register” on page 5-8). Upon power-up or after a hard reset, the GEIP-provided firmware will check the EM_BOOT_SEL bit to determine which boot code area to execute boot code from.

  • Page 52: Device Bus

    ETH2 to cPCI_J4. The MV64460 System Controller provides three Ethernet Media Access Controllers (MACs). The VSC8244 PHY provides the physical interfaces. The C2K provides nine on-board LEDs to monitor link activity and data transfer speeds for the three Ethernet ports as described in Table 4-1.

  • Page 53: Serial I/O

    COM5–COM8 serial ports configured as RS-485. When these ports are configured as RS-422, the receive termination must always be enabled and the transmit termination must always be disabled. C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 54: Usb Ports

    0# and AD bit 16 for IDSEL. The PCI2050B secondary clock outputs are not used and should be disabled by application software. The C2K provides four on-board green LEDs to diagnose USB port activity as listed in Table 4-2. USB on-board indicator LEDs...

  • Page 55: Counter/Timers

    FPGA, which generates a SMI# to interrupt the processor. If the watchdog timer expires, it asserts the WDOG_EXP output to the FPGA, which will initiate a board reset as shown in Figure 4-1 on page 4-8. C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 56: Fpga

    Each interrupt source is maskable through the FPGA SMI Mask Register (see “SMI Mask Register” on page 5-14). These mask bits are set at reset. C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 57: Rtc

    4.15 CompactPCI Backplane Interface The C2K employs the PCI 6254 Dual Mode PCI/PCI Bridge to transfer PCI data between the PCI Bus 1 and the backplane PCI 2.2 compatible cPCI bus. The PCI 6254 provides all the power entry, system control, and cPCI bus interface wiring defined for 6U system controller and peripheral slot boards defined in PICMG 2.0.
  • Page 58 SYSEN# signal from the backplane (cPCI_J2 C2). SYSEN# is asserted when the C2K is installed in a system slot and de-asserted when the C2K is installed in a peripheral slot. NOTE: The cPCI 64EN# backplane signal is connected to the PCI 6254 64EN# input pin. The state of 64EN# can be determined by an internal PCI 6254 register.

  • Page 59: Ipmi And Hot Swap

    • C8051F127 Microcontroller (C8051) 4.16.1 Hot Swap Controller The LTC4244-1 Hot Swap Controller (HSC) allows the C2K to be installed or removed from a CompactPCI chassis while the chassis is powered-up. The HSC provides the PCI signal pre-charge voltage and controls the C2K’s main power. The HSC also monitors the main on-board voltage rails: +5V, +3.3V, and ±12V.

  • Page 60: Table 4-4 C8051 External I/O Ports Pin Assignments

    I/O to support C8051 features, and hold the state of the output signals (UART_RESET#, FPGA_INT#, and BRD_RST#) during a watchdog-initiated C8051 Controller reset. C2K User’s Guide 4-12 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 61: Table 4-5 I/O Controller Pin Assignments

    +5V, +3.3V, and +12V supplies. BRD_RST# is an open-drain output with an external pull-up that is used to initiate a board reset. The C2K is held in reset while this signal is active.

  • Page 62: Pmc Sites

    • Reserved pins are not connected. • Reset signals from each PMC site are isolated from the C2K, such that the C2K can drive the PMC reset, but the PMC reset will not be acknowledged by the C2K. This prevents the C2K from being reset when an installed PMC module initiates a reset.

  • Page 63: Pmc1 Site Features

    • Generate over-temperature alarm at +85ºC or above The over-temperature alarm is ignored unless the OVRTEMP_RST_EN bit (bit 15) in the FPGA Control Register (see “Control Register” on page 5-9) is set. This avoids resetting the C2K prior to the CPU reprogramming the sense thresholds.

  • Page 64: Eeproms

    RTC_INT PCI 6254_PINT SATA_INT USART_INT0–7 TEMP_INT USB_INT Interrupt circuitry Figure 4-3 4.20 EEPROMS The C2K provides the following programmable configuration serial EEPROMS located on the IIC SMBus: EEPROM Type Address Function Board Configuration AT24C64AN 0x50 Provides storage for product configuration data such as: assem- (64kb) bly serial number, build data, etc.

  • Page 65: Jtag Boundary Scan Circuitry

    Functional Blocks 4.21 JTAG Boundary Scan Circuitry The JTAG circuitry provides a boundary scan chain for checking major components on C2K for open and short circuits, and grounds. It can also be configured for special functions such as COP software debugging through the COP header (J6) and C8051 Microcontroller software debugging.

  • Page 66: Figure 4-4 Jtag Circuitry

    PCI 6254_TDI 64460_TDI Controller Bridge PCI 6254_TDO 64460_TDO PMC1_TDO PCI2050B PCI/PCI PCI2050B_TDI PMC1 Bridge PMC1_TDI PCI2050B_TDO PMC0_TDO PMC0 PMC0_TDI JTAG circuitry Figure 4-4 C2K User’s Guide 4-18 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 67: Chapter 5: Resources

    5.1 Memory and I/O Address Mapping 5.1.1 PCI Buses The C2K provides two PCI buses controlled through the MV64460 System Controller’s two PCI bus interfaces. PCI Bus 0 is dedicated to the PMC0 site and supports 64-bit 33/66MHz PCI or 133MHz PCI-X operation.

  • Page 68: Smbus

    Resources 5.1.2 SMBus The C2K provides a System Management Bus (SMBus), a two-wire IIC interface that can com- municate configuration or status information with other components following the I2C protocol. The MV64460 System Controller provides the SMBus Host Controller to five slave ports. Table 5-2 lists the slave devices and their 7-bit addressing used by the devices.

  • Page 69: Multi-Purpose Pins (Mpp)

    PCI1_REQ2 (PCI2050B) TEMP_INT PCI1_GNT3 (GD31244) ETH_PHY_INT PCI1_REQ3 (GD31244) GPIO_INT S0_TXD FPGA_INT S1_SCLK TC_NT0 S1_TSCLK TC_EN1 S1_RXD USB_INT S1_TXD CNTR_INT S0_SCLK TC_NT2 S0_TSCLK TC_EN3 S0_RXD SATA_INT C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 70: Fpga Registers

    Resources 5.2 FPGA Registers The C2K includes a FPGA to provide programmable logic circuitry for peripheral resources and miscellaneous ‘glue logic’. The FPGA, located on the 32-bit Device Bus, contains registers that perform the following functions: • Board status and control •...
  • Page 71 0x22C Counter 11 Current Value High 0x22E Counter 11 Current Value Low 0x230 Counter 12 Current Value High 0x232 Counter 12 Current Value Low C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 72 0x278 Counter 14 Preload Value High 0x27A Counter 14 Preload Value Low 0x27C Counter 15 Preload Value High 0x27E Counter 15 Preload Value Low C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 73: Main Registers

    NOTE: The revision number is subject to change. Address offset: Access: Read-only Bits Field Default Description 15 to 8 0x01 Revision (major) number 7 to 0 0x01 Version (minor) number C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 74 Resources Status Register The Status Register provides C2K status information such as flash and system memory size, flash write-protect, and emergency boot select settings. NOTE: Bits 15–12 only revert to the default value during power-up and are not affected by resets.
  • Page 75 COM3 Interface Select—selects the COM3 interface type. 0 = RS-422 1 = RS-232 COM4_TYPE COM4 Interface Select—selects the COM4 interface type. 0 = RS-232 1 = RS-422 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 76 PHY Hard Reset Control 0 = reset negated 1 = reset asserted PHY_SOFT_RESET PHY Soft Reset Control 0 = reset negated 1 = reset asserted C2K User’s Guide 5-10 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 77: Interrupt Registers

    CPCI interrupt. When the board is not in the system controller slot, the CPCI interrupts are disabled. 0 = enable interrupt 1 = disable (mask) interrupt 5-11 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 78 USART1 INT Mask—blocks (masks) the USART interrupt. 0 = enable interrupt 1 = disable (mask) interrupt USART0_INT_MSK USART0 INT Mask—blocks (masks) the USART interrupt. 1 = disable (mask) interrupt C2K User’s Guide 5-12 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 79 PMC0 INTD Status—indicates the status of INTD from a PMC module installed on PMC0. 0 = interrupt is de-asserted 1 = interrupt is asserted 5-13 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 80 FAL# signal Mask—blocks (masks) the backplane FAL# signal from asserting the CPU_SMI#. 0 = enable FAL# signal 1 = disable (mask) FAL# signal C2K User’s Guide 5-14 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 81 NMI on GPIO15 Input Active (if enabled)—indicates the NMI signal is active on the GPIO15 line. 0 = input inactive 1 = input active 5-15 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 82: Gpio Registers

    Resources 5.2.3 GPIO Registers The C2K includes 16 General-Purpose Input/Output ports. The FPGA provides the GPIO inter- rupt masking, data, and control registers for configuring, masking interrupts, and sending/receiv- ing data on the GPIO lines connected to the backplane. The FPGA also includes an optional de-bounce circuit that can be applied to each port designated as an input for use with external switches, contacts, or relays.
  • Page 83 1 = output GPIO5_DIR GPIO5 Direction—enables the circuit direction (i.e., input or output) for the GPIO5 line. 0 = input 1 = output 5-17 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 84 1 = output GPIO0_DIR GPIO0 Direction—enables the circuit direction (i.e., input or output) for the GPIO0 line. 0 = input 1 = output C2K User’s Guide 5-18 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 85 1 = active low GPIO5_POL GPIO5 Polarity—enables the circuit polarity (i.e., high or low) for the GPIO5 line. 0 = active high 1 = active low 5-19 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 86 1 = active low GPIO0_POL GPIO0 Polarity—enables the circuit polarity (i.e., high or low) for the GPIO0 line. 0 = active high 1 = active low C2K User’s Guide 5-20 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 87 1 = open-drain output GPIO5_OUTPUT_TYPE GPIO5 Output Type—enables the output type for the GPIO5 line. 0 = actively driven output 1 = open-drain output 5-21 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 88 1 = open-drain output GPIO0_OUTPUT_TYPE GPIO0 Output Type—enables the output type for the GPIO0 line. 0 = actively driven output 1 = open-drain output C2K User’s Guide 5-22 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 89 GPIO5_INTERRUPT_TYPE GPIO5 Interrupt Type—enables the signal sensitivity interrupt type for the GPIO5 line. 0 = select level-sensitive interrupt 1 = select edge-sensitive interrupt 5-23 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 90 GPIO0_INTERRUPT_TYPE GPIO0 Interrupt Type—enables the signal sensitivity interrupt type for the GPIO0 line. 0 = select level-sensitive interrupt 1 = select edge-sensitive interrupt C2K User’s Guide 5-24 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 91 GPIO8 Debounce Enable—enables a debounce circuit for GPIO8 line if designated as an input in the Control Register. 0 = disable de-bounce circuit 1 = enable de-bounce circuit 5-25 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 92 GPIO0 Debounce Enable—enables a debounce circuit for GPIO0 line if designated as an input in the Control Register. 0 = disable de-bounce circuit 1 = enable de-bounce circuit C2K User’s Guide 5-26 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 93 1 = active state GPIO6_INPUT_DATA GPIO6 Input Data Read—reads the GPIO Polarity Register for the GPIO6 line 0 = inactive state 1 = active state 5-27 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 94 GPIO Polarity Register for the GPIO14 line 0 = inactive state 1 = active state C2K User’s Guide 5-28 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 95 GPIO Polarity Register for the GPIO4 line 0 = inactive state 1 = active state 5-29 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 96 1 = interrupt active GPIO13_INT_STAT GPIO13 Interrupt Status—provides the GPIO interrupt status for the GPIO13 line 0 = interrupt not active 1 = interrupt active C2K User’s Guide 5-30 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 97 1 = interrupt active GPIO0_INT_STAT GPIO0 Interrupt Status—provides the GPIO interrupt status for the GPIO0 line 0 = interrupt not active 1 = interrupt active 5-31 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 98 1 = disable (mask) interrupt GPIO5_INT_MSK GPIO5 Interrupt Mask—blocks (masks) GPIO5 interrupt out- put. 0 = enable interrupt 1 = disable (mask) interrupt C2K User’s Guide 5-32 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 99 CPIO Control Register settings. 0 = does not affect the corresponding GPIO11 bit 1 = clear the corresponding GPIO11 bit 5-33 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 100 GPIO Set Register The GPIO Set Register can directly assert a corresponding line in the Data Register without requiring a read-modify-write cycle. Address offset: 0x4E C2K User’s Guide 5-34 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 101 GPIO4 Set —asserts the GPIO4 line. Polarity is determined by the corresponding bit in the Control Register. 0 = does not affect GPIO4 bit 1 = set the corresponding GPIO4 bit 5-35 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 102 GPIO0 Set —asserts the GPIO0 line. Polarity is determined by the corresponding bit in the Control Register. 0 = does not affect GPIO0 bit 1 = set the corresponding GPIO0 bit C2K User’s Guide 5-36 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 103: Counter/Timers

    Counter 12 Enable—enables counter 12. 0 = disable counter 1 = enable counter CNTR11_EN Counter 11 Enable—enables counter 11. 0 = disable counter 1 = enable counter 5-37 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 104 Counter 14 Disable—disables counter 14. 0 = no effect 1 = disable CNTR13_DISABLE Counter 13 Disable—disables counter 13. 0 = no effect 1 = disable C2K User’s Guide 5-38 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 105 Counter 1 Disable—disables counter 1. 0 = no effect 1 = disable CNTR0_DISABLE Counter 0 Disable—disables counter 0. 0 = no effect 1 = disable 5-39 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 106 0 = counter 1 = timer CNTR3_MODE Counter 3 Mode—configures counter 3 as a timer or counter. 0 = counter 1 = timer C2K User’s Guide 5-40 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 107 1 = disable (mask) interrupt CNTR8_INT_MSK Counter 8 Interrupt Mask—blocks (masks) the interrupt for counter 8. 0 = enable interrupt 1 = disable (mask) interrupt 5-41 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 108 1 = interrupt is asserted CNTR14_INT_STAT Counter 14 Interrupt Status—provides current interrupt status for counter 14. 0 = interrupt is de-asserted 1 = interrupt is asserted C2K User’s Guide 5-42 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 109 1 = interrupt is asserted CNTR1_INT_STAT Counter 1 Interrupt Status—provides current interrupt status for counter 1. 0 = interrupt is de-asserted 1 = interrupt is asserted 5-43 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 110 0x242, 0x246, ... 0x27E Access: Read/write Bits Field Default Description 15 - 0 CNTR_PRELOAD_LOW 0xFF Counter Preload Low Value—lower 16 bits of 32-bit counter/timer preload value C2K User’s Guide 5-44 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 111: Usart Registers

    Parity Error Test Mode—inverts transmitted parity bit. 0 = parity bit non-inverted 1 = parity bit inverted NOTE: This bit must be cleared (0) for normal operation. 5-45 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 112: Standard Usart Registers

    Address offset: USART_Base +0x0 DLAB: Access: Read-only Bits Field Default Description 7 - 0 RXDATA 0x00 Receive buffer data C2K User’s Guide 5-46 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 113 0b00 FIFO Buffer status—indicates the status of the FIFO buffer. 0b11 = FIFO mode is enabled 5 - 4 Not used Not used 5-47 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 114 0b01 = 32 bytes 0b01 = 64 bytes 0b10 = 64 bytes 0b10 = 128 bytes 0b11 = 128 bytes 0b11 = 256 bytes C2K User’s Guide 5-48 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 115 Stick Parity—enables stick parity, which transmits and checks parity as a (0) for odd parity and a (1) for even parity. 0 = disable stick parity 1 = enable stick parity 5-49 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 116 1 = RTS is set to (0) External Data Terminal Ready—controls the DTR signal. 0 = DRT is set to (1) 1 = DTR is set to (0) C2K User’s Guide 5-50 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 117 Shift Register. This bit also generates a Receiver Line Status inter- rupt. The Overrun Error bit is cleared when read. 0 = no overrun error has occurred 1 = overrun error has occurred 5-51 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 118 Address offset: USART_Base +0x7 Access: Read/write Bit(s) Field Default Description 7 - 0 SCRATCH 0x00 Scratchpad data—number of bytes in the Receive FIFO C2K User’s Guide 5-52 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 119: Usart Divisor Latch Registers

    +0.16 2400 +0.16 9600 +0.16 19200 +0.16 38400 +0.16 57600 +0.16 115.2k +0.16 230.4k +0.16 460.8k +0.16 921.6k +0.16 1.8432M +0.16 3.6864M +0.16 5-53 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 120: Component Locations

    Resources 5.3 Component Locations Figure 5-1 shows the C2K major component locations. (Drawing not to scale) C2K component locations (primary side) Figure 5-1 C2K User’s Guide 5-54 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 121 Resources This page is intentionally left blank. C2K component locations (secondary side) Figure 5-2 Component Legend ISP1563 USB 2.0 Controller M41T62 RTC DDR SDRAM Bank 0 XC3S1200E FPGA MV64460 System Controller PCI 6254 PCI/cPCI Bridge MCP7447A/MPC7448 PPC G4 processor Flash Memory...

  • Page 122: Chapter 6: Transition Module C2K-Tm

    Chapter 6: Transition Module C2K-TM 6.1 Overview GEIP provides the C2K Rear Transition Module (C2K-TM) as an optional companion board for the C-style C2K Single Board Computer. The C2K-TM provides the following connections: • BATT+ (P13)—on-board 2 x 5 connector •...

  • Page 123: Physical Description

    Transition Module C2K-TM 6.2 Physical Description NOTE: The C2K-TM is only offered in a C-style version. Form Factor: 6U RTM per PICMG 2.0 Height: 233.20 ± 0.15 mm (9.1811 ± 0.0059 in.) Depth: 79.85 ± 0.15 mm (3.15 ± 0.0059 in.)

  • Page 124: Block Diagram

    Transition Module C2K-TM 6.3 Block Diagram PB_RST# cPCI_J5 BATT+ ICMB ROM_WP# GPIO EM_BOOTSEL# USB1 BATT+ PMC1 I/O USB2 PB_RST# USB3 COM1 COM8 cPCI_J4 COM2 COM7 COM6 SATA0 COM5 COM4 SATA1 RS-232 COM3 COM2 COM3 RS-232 ETH2 COM1 ETH0 cPCI_J3 PMC0 I/O...

  • Page 125: Connector Pin Assignments

    Transition Module C2K-TM 6.4 Connector Pin Assignments 6.4.1 CompactPCI Connectors CompactPCI J3 The cPCI_J3 connector provides the following signal groups: • PMC0 I/O • ETH0 Gigabit Ethernet connections • ETH1 Gigabit Ethernet connections • +3.3V and +5V supply voltages. CompactPCI connector J3 pin assignments...

  • Page 126: Table 6-2 Cpci Connector J4 Pin Assignments

    Transition Module C2K-TM CompactPCI J4 The cPCI_J4 connector provides connections for the following I/O ports: • RS-232 serial ports COM3 and COM4 • RS-422 serial ports COM1 through COM4 • RS-422/485 serial ports COM5 through COM8 • Gigabit Ethernet port (ETH2) •...
  • Page 127 • BATT+—for connecting a +3.3V supply for NVRAM and RTC battery backup • BIT_PASS#—for the on-board LED1 indicator • NMI#—Non-maskable interrupt • ROM_WP#—Flash ROM write-protect • PB_RST_IN#— for rear-panel push-button reset input • PMC_JTAG_EN#—not used on C2K-TM CompactPCI connector J5 pin assignments Table 6-3 J5-22 PMC1_5...

  • Page 128: Ethernet Connectors (J6, J7, And J8)

    Figure 6-2 6.4.3 Serial ATA Connectors (P19, P20) The C2K-TM provides two serial ATA rear- panel connectors: SATA1 (P19), and SATA2 (P20). The pin assignment listed in Table 6-5 applies to both P19 and P20 SATA connectors. Serial ATA connectors (P19,...

  • Page 129: Usb Connectors (J9, J10, And J11)

    Transition Module C2K-TM 6.4.4 USB Connectors (J9, J10, and J11) The C2K-TM provides three rear-panel standard Type A USB connectors: USB1 (J9) and USB2 (J10) and USB3 (J11). The pin assignment listed in Table 6-6 applies to all three USB connectors.

  • Page 130: Serial Rs-422/485-Com1-Com8 (P1-P8)

    COM3/4_TXD 6.4.8 BATT+ Header (P13) The C2K-TM provides an on-board 2 x 5-pin header (P13) for the BATT+ line. A +3.3V supply can be connected to the BATT+ header to provide power to the NVRAM/RTC device as a battery backup when the C2K is not powered-on but still installed in a chassis slot.

  • Page 131: Icmb Interface Header (P17)

    ICMB_D+ ICMB_D- 6.4.10 GPIO Connector (P14) The C2K-TM includes an on-board 2 x 10-pin header (P14) for access to the GPIO Status and Control signals. NOTE: Samtec IDSD Series connectors can be used to mate with the GPIO connector. GPIO on-board header (P2) pin assignments...

  • Page 132: Misc. Connector (P18)

    Transition Module C2K-TM 6.4.11 Misc. Connector (P18) The C2K-TM provides an on-board 2 x 5-pin header (P18) that can be used as a jumper site for the EM_BOOTSEL# and ROM_WP# signals. Jumpers can be installed on pins 1/2 to assert (active low) the EM_BOOTSEL# signal (see “Boot Code Selection”...

  • Page 133: Pmc I/O Connectors (P11 And P12)

    Transition Module C2K-TM 6.4.12 PMC I/O Connectors (P11 and P12) The C2K-TM provides two on-board 2 x 32-pin PMC I/O headers: PMC0 I/O (P11) and PMC1 I/O (P12). PMC0_P11 and PMC1_P12 pin assignments. Table 6-14 PMC0 I/O (P11) PMC1 I/O (P12)

  • Page 134: Connector Locations

    Transition Module C2K-TM 6.5 Connector Locations USB 3 USB 3 USB 2 USB 2 USB 1 USB 1 SATA SATA SATA SATA ETH 0 ETH 0 ETH 1 ETH 1 ETH 2 ETH 2 RESET RESET COM1–232 COM1–232 COM2–232 COM2–232...

  • Page 135: Tm Schematics

    COM5 RS-422/485 on-board header SATA2 rear-panel connector COM6 RS-422/485 on-board header Board reset rear-panel switch 6.6 TM Schematics Please see following pages for C2K-TM schematics. 6-14 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 136 Transition Module C2K-TM C2K User’s Guide 6-15 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 137 Transition Module C2K-TM 6-16 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 138 Transition Module C2K-TM C2K User’s Guide 6-17 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 139 Transition Module C2K-TM 6-18 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 140 Transition Module C2K-TM C2K User’s Guide 6-19 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 141 Transition Module C2K-TM 6-20 C2K User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 142 Maintenance If a GE product malfunctions, please verify the following:  1.  Software version resident on the product 2.  System configuration 3.  Electrical connections 4.  Jumper or configuration options 5.  Boards are fully inserted into their proper connector location 6.  Connector pins are clean and free from contamination 7.  No components or adjacent boards were disturbed when inserting or remov‐ ing the board from the chassis 8.  Quality of cables and I/O connections If products must be returned, contact GE for a Return Material Authorization  (RMA) Number. This RMA Number must be obtained prior to any return.  RMA request forms can be obtained from: www.ge-ip.com/rma GE Technical Support is  available at: 1‐800‐433‐2682 in North America, or +1‐780‐401‐7700 for international calls. Requests for Technical Support can be  sent to:  support.huntsville.ip@ge.com Or, visit our website: www.ge-ip.com Maintenance Prints User level repairs are not recommended. The drawings and diagrams in this  manual are for reference purposes only. Maintenance 21 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 143 ........5-8 Boot code selection configuration ........5-9, 5-10 control ......5-7 firmware release ID ........1-5 ......5-32 C2K Block diagram GPIO interrupt mask ........... 1-1 ......5-11, 5-13 C2K Overview interrupt mask C2K-TM ........6-3 block diagram ......6-13 ..........
  • Page 144 ........ 4-5 Quad UART (RS-422) ........... 1-3 Vibration ........4-9 Real-Time Clock ........1-7 Related Documents ......... 4-7 Watchdog timer ............1-4 Safety C2K User’s Guide Index-2 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 145 Additional Resources Systems, Inc. All rights reserved. Information Centers For more information, please visit * indicates a trademark of GE Intelligent Platforms, Inc. and/or its affiliates. All other the GE Intelligent Platforms Embedded Americas: trademarks are the property of their respective...
  • Page 146 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...

Table of Contents