Remote Control Batteries; Ac Power And Control; Ac Power Input; Power Switch And Power Indicator 1A - Rotel RA-1572 Owner's Manual

12
2. Point the remote at the unit and press 2
unit will show "AUDIO CODE SET 1 -> 2".
3. Repeat the above procedure and press "1" button instead of "2" to change
the unit back to Code 1.
NOTE: The remote control can be used to operate the basic functions
of Rotel tuners and CD players. Remote control buttons labeled
FIJNOQ
can be used to operate CD or Tuner functions in your
system. For the remote to operate properly, make sure both the remote
and the CD or Tuner are both in same remote code, either Code 1 or 2.

Remote Control Batteries

Two AAA size batteries (supplied) must be installed before the remote
control can be used. To install the batteries, remove the cover on the back
of the RR-AX93. Install the batteries as shown in the illustration in the battery
well. Test the control for proper operation, then replace the cover. When
the batteries become weak the remote control won't operate the RA-1572
consistently. Installing fresh batteries should eliminate the problem.

AC Power and Control

AC Power Input \

Your RA-1572 is configured at the factory for the proper AC line voltage in
the country where you purchased it (either 120 volts AC or 230 volts AC
with a line frequency of either 50 Hz or 60 Hz). The AC line configuration
is noted on a decal on the back panel.
NOTE: Should you move your RA‑1572 to another country, it is possible
to reconfigure your amplifier for use on a different line voltage. Do not
attempt to perform this conversion yourself. Opening the enclosure of
the RA‑1572 exposes you to dangerous voltages. Consult a qualified
service person or the Rotel factory service department for information.
NOTE: Some products are intended for sale in more than one country
and as such are supplied with more than one AC cord. Please only use
the one appropriate for your country/region.
Because of its relatively high power rating, the RA-1572 can draw considerable
current. Therefore, it should be plugged directly into a polarized wall
outlet using the supplied cable or other high current compatible cable as
recommended by your authorized Rotel dealer. Do not use an extension
cord. A heavy duty multi-tap power outlet strip may be used if it (and the
wall outlet) is rated to handle the current demanded by the RA-1572 and
all the other components connected to it.
If you are going to be away from home for an extended period of time
such as a month-long vacation, it is a sensible precaution to unplug your
amplifier (as well as other audio and video components) while you are away.
POWER Switch and Power Indicator 1 A
Press the front panel Power Switch button, to turn the unit on. The Power
Indicator light is illuminated when the unit is on. Press Power Switch button
again to turn the unit off.
O button for 14 seconds. The
RA‑1572 Stereo Integrated Amplifier
When the power switch is in the ON position, the remote control ON and
OFF buttons A may be used to activate the RA-1572. In Standby mode the
power LED remains illuminated, but the display is turned off.

12V TRIGGER Connection [

See Figure 7
Some audio components can be turned on automatically when they receive
a 12V turn on signal. The two 12V Trigger Outputs of the RA-1572 provide
the required signal. Connect compatible components to the RA-1572 with
a conventional 3.5mm mini plug cable. When the RA-1572 is in standby
mode or turned off, the trigger signal is interrupted, so the components
controlled by it are turned off.
NOTE: If you are using other units in the series with Rotel Link, please
use the Rotel Link connection to turn the units on or off. Do not connect
both the Rotel Link and 12V trigger cables. The 12V trigger's power
on or off features will override the Rotel Link features.

Input Signal Connections

NOTE: To prevent loud noises that neither you nor your speakers will
appreciate, make sure the system is turned off when you make any
signal connections.

Phono Input - and Ground Connection (GND) 0

See Figure 3
Plug the cable from the turntable into the appropriate left and right phono
inputs. If the turntable has a "ground" wire, connect it to the screw terminal
to the left of the Phono inputs. It will help prevent hum and noise.

Line Level Inputs -

See Figure 3
The CD, Tuner, and Aux inputs of the amplifier are analog "line level" inputs.
These inputs are for connecting components such as CD players or other
audio playback devices with an analog audio output.
The left and right channels are clearly labeled and should be connected to
the corresponding channels of the source component. The Left connectors
are white, the Right connectors are red. Use high quality RCA cables for
connecting input source components to the RA-1572. Ask your authorized
Rotel dealer for advice about cables.
Balanced (XLR) Inputs
w
See Figure 5
A pair of balanced XLR inputs accept audio signals from CD player, Blu-ray
player or other source components with XLR outputs.