Download Table of Contents Print this page

Control Panel - Black & Decker VEC1093DBD User Manual

Fully automatic electronic smart battery charger
Hide thumbs Also See for VEC1093DBD:

Advertisement

Table of Contents
VECI093DBDManual
050205
5/5/05
6:32
PM
Page
2
Stage
TMZO -- Absorption
Charge
maintains
the maximum
possible charge
at a
constant, safe, predetermined
voltage.
During this phase, the charging voltage remains
constant, while the actual charging current is reduced to allow for the maximum proper
internal chemical energy transfel. At the end of Stage 2, the charger will automatically
move into Stage 3 charge mode.
Stage
Three
--
Top-Off
Charge
--
voltage
is automatically
maintained
and
reduced to a predetermined
level while current is adjusted for a safe, effective battery
chalge.
At the conclusion
of Stage 3, the unit will BEEP signaling
the completion
of
the charging
cycle.
The Automatic
Float Charge feature is ideal for maintaining
a battery. It automatically
tops off battery as needed to keep battery fully charged
all the time.
FEATURES
. This unit has four charge rate settings, accessed by the 4/10/20/40
AMP button:
a) 4 amps: smaller batteries,
as in lawn mowers,
snowmobiles,
motorcycles,
etc.
b) 10 amps: mid-sized batteries, as in small cars
c) 20 amps: automobiles
and light trucks
d) 40 amps: large truck batteries, banks of RV batteries
. 110 amp engine start
• Automatic
Temperature Compensation
• Battery type selection
- Digital
diagnostics
- Alternator
voltage and battery voltage check
• Digital
display
shows cl/arge
rate, operating
mode,
fault codes and FUL when
charged
• 1-minute engine start
• 3-stage high-frequency
switch mode automatic
rapid charging
- Spark resistant reverse polarity
and short circuit protection for user
. Built-in battely
reconditioning
(desulfate)
• Lightweight,
high-efficiency
design
• Internal short circuit protection
- Cables and clamps self-stored
- Reverse polarity
indication
• Microprocessor
control (Digital Smart Control) Mgh frequency power
• Compensates
for low AC from extension cord use
• Equalization
function
- Battery recondition
function
Controls
and
Indicators
CONTROL PANEL
DIGITAL READOUT
CIRCULATING PATtERN
FUNCTION
BUTTONS (FROM
LEFT TO RIGHT):
Battery
Type
(Step 1) -- allows the user to seled Wet, Gel or AGM type of battery
for efficient and safe charge.
Most automotive
batteries are Wet batteries. Refer to tile
battery
n/anufacturer's
specifications
for battery type.
4/10/20/40
AMP
(Charge
Rate
Selector)
(Step 2) -- allows tile user to select
the charge
rate based on battery
size. This selection
and the actual battery charge
rate are monitored
by the microprocessor.
The charger will stop charging
if the rate
is too fast or too slow for the battery
size or condition.
1 10 AMP
Engine
Start -- places tile charger
in an engine start sequence. This
button will not be activated unless the charger is in the 40 amp charge mode; set the
4/10/20/40
AMP button to 40 amps first to activate this button.
Battery
Recond.
-- is an automatic mode that, once started, continues for 24 hours
and then stops, A series of electrical
pulses breaks the crystalline
form of lead sulfate
to return these chemicals
into useful battery electrolytes.
More than 24 hours may be
needed
to restore. Periodic
reconditioning
is recommended
to maintain
a bauery's
optimum performance.
However,
if 5 cycles does not improve battery
performance,
discontinue
and lecycle the battery.
Battery
Voltage
(Aiternatar
Voltage
Check)
-- is a quick check that measures
tile battery
voltage,
Tl/is check is repeated
at various electrical
load levels and tile
tests allow the user to determine
if tile alternator
can keep up with the loads,
2
3

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents