Table of Contents
Advertisement
OBJ_BUCH-1502-001.book Page 16 Thursday, November 3, 2011 3:02 PM
16 | English
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Plug for vacuum connection
3 Auxiliary handle (insulated gripping surface)
4 Protection guard with quick clamp
5 Spindle lock button
6 Holder for vacuum hose
7 Handle (insulated gripping surface)
8 Clamping lever for protection guard
9 Grinder spindle
10 Mounting flange with O-ring
11 Diamond cutting disc*
12 Clamping nut
13 Two-pin spanner for clamping nut
14 Quick-clamping nut
15 Index mark*
16 Dry diamond core bit*
17 Open-end spanner, size 19 mm*
18 Vacuum hose
19 Elbow
20 Vacuum connection
21 Extraction adapter
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cut-off Grinder
Article number
Rated power input
No-load speed
Max. diameter for diamond cutting
discs
Cutting discs width, min.
Cutting discs width, max.
Mounting bore
Thread of grinder spindle
Thread length (max.) of grinder
spindle
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
2 610 017 516 | (3.11.11)
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 100 dB(A); Sound power level
111 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 60745:
Cutting tiles (50 mm): a
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
*
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
GCT 115
2004/108/EC, 2006/42/EC.
Professional
Technical file (2006/42/EC) at:
3 601 C91 0..
Robert Bosch GmbH, PT/ETM9,
W
720
D-70745 Leinfelden-Echterdingen
-1
min
11000
Dr. Egbert Schneider
Senior Vice President
mm
115
Engineering
mm
1
mm
3
mm
22.2
M 14
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
13.10.2011
mm
22
Assembly
kg
1.9
/II
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales
service agent for maintenance for addresses, see section "Af-
ter-sales Service and Customer Assistance".
(triax vector sum) and uncertainty K
h
2
2
=2.5 m/s
, K=1.5 m/s
.
h
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
Bosch Power Tools
Advertisement
Table of Contents
