Summary of Contents for CYP HDBaseT 5Play PUV-1510RX
Page 1
PUV-1510RX HDBaseT™ 5Play™ Receiver (inc. PoH & single LAN, up to 100m) OPERATION MANUAL...
Page 3
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document.
Page 4
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
1. INTRODUCTION The HDMI over single CAT5e/6/7 Receiver can receive uncompressed audio/video and IP data over a single run of CAT5e/6/7 cable at a distance up to 100 meter. It has the added benefit of control through the built-in RS-232 and IR ports and a bi-directional LAN serving connection. The Receiver (PD) can be powered by the PoE 48V function of the Transmitter (PSE), allowing for greater flexibility in installations.
5. FEATURES HDMI with 3D, 4K2K support, HDMI & DVI Compliant Supports CEC bypass Simultaneous reception of uncompressed data over a single 100m/328ft CAT5e/6/7 cable 5Play™ convergence: HDMI, LAN, PoE & Control (IR & RS-2232) Supports resolution up to 4K2K@50/60 & YUV_420 and 21:9 Supports standard 48V from Transmitter (PSE) to Receiver (PD) Installation Friendly Supports HDMI Output cable distance up to 5m at 4K2K@50/60 &...
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel BLASTER HDMI OUT EXTENDER IR2 BLASTER: Connect to the supplied IR Blaster cable for IR signal transmission. Place the IR Blaster in direct line-of-sight of the equipment to be controlled. IR1 EXTENDER: Connect to the supplied IR Extender cables for IR signal reception.
6.2 Rear Panel RS-232 OUT POWER STD UPDATE LINK STD/UPDATE Switch: This switch is reserved for factory use only. RS-232 OUT: Connect to the device that is to be controlled (via D-Sub 9-pin female cable) by RS-232 commands. LAN: Connect to a PC or Laptop to utilise the Internet or network function.
7. CONNECTION DIAGRAM RS-232 Equipped PC or Notebook Internet Modem or Router CAT5e/6 1.5m 60° DVD or Blu-ray Player RS-232 IR Blaster Power Supply RS-232 IN POWER STD UPDATE HDMI LINK BLASTER 60° HDMI IN DC 48V EXTENDER IR Extender IR Extender 60°...
8. SPECIFICATIONS Video Bandwidth 340MHz / 10.2Gbps Inputs 1 x CAT5e/6/7, 1 x IR Extender Outputs 1 x HDMI, 1 x RS-232, 1 X IR Blaster, 1 x LAN HDMI Resolution HD: 480i~4K2K@24/25/30/50/60 & YUV_420 PC: VGA ~ WUXGA (RB) HDMI Cable Distance Out: 10m/1080p@8-bit, 5m/1080p@12-bit and 5m@4K2K...
8.1 CAT5e/6/7 Cable Specification Cable Range Pixel clock Video Data Supported Video Type rate Rate CAT5e/6/7 100 m <=225 MHz <=5.3 Gbps Up to 1080p, 60 Hz, 36 bits, 3D (HD Video) (data rates lower than 5.3 Gbps or below 225 MHz TMDS clock).
Need help?
Do you have a question about the HDBaseT 5Play PUV-1510RX and is the answer not in the manual?
Questions and answers