Download Print this page

Apogee 00524 Manual

Fin shape science experiment kit

Advertisement

Quick Links

Skill Level 2: Previous Rocket Experience Sug-
gested
A fun science project is to test various fin shapes
on a rocket to find out which one is best. The key to
any good experiment is to limit the variables so that
just one item affects the outcome. In this kit, we've
designed the rocket so that the rocket stays the same
and only the fin shape changes. We further isolated the
shape of the fin by making sure that the surface area
is identical from one shape to the next, and that the fin
span (how far it sticks out into the air) is also the same.
In this kit, there are four pre-cut fin shapes you can
test, and another eleven patterns that you can choose
from to make your own hand-cut fins.
To change out the fins, you simply slide the fin unit
off the rocket and slide on a new one. The shapes can
be swapped out in just a few seconds!
p/n 31133
Fin Shape Science
Experiment Kit
Test Different Fin Shapes to Find Out
Which One Performs the Best!
P/N
Description
10079
AT-18/5.4" (Fin Shape Sci Eng. Mount Tube) 1
10118
AT-33/3" (Payload Tube)
10119
AT-33/4" (Fin Can Body Tube)
10120
AT-33/9" (Main Body Tube)
13016
Coupler AC-33 (red)
13029
CR 13/18 (blue) Centering Ring
13051
1/8" Launch Lug 1" Long
14101
Balsa Sheet 3" X 9" X 1/8"
15596
Elliptical Fin Sheet (Balsa)
15597
Trapezoid Fin Sheet (Balsa)
15598
Rectangular Fin Sheet (Balsa)
15599
Shark Fin Sheet (Balsa)
15602
Plywood Ring Set (Fin Shape Science)
19468
PNC-33mm (BT-55)
24043
Crimped Engine Hook
29124
Apogee 12" Plastic Parachute Pack
29519
100# Kevlar X 6 ft
29600
Clay mass - 5 grams
29610
Small Screw Eye
31133
Instruction Sheet A
31134
Instruction Sheet B
31135
Fin Shape Science Data Collection Sheet
35575
13/18mm Display Stand (Cardstock)
35538
33mm 3-Fin Alignment Guide (Cardstock)
41047
Decal Sheet (Fin Shape Science)
47133
Clear Plastic Bag 10x6x24
Other Tools and Materials Needed
Pencil
Ruler with a straight edge
Hobby knife
Wood glue
Rubber cement, spray adhesive, or glue stick
Masking tape
Paper towels
Paint supplies (spray paint, brushes, etc.)
Wood sealer
Sandpaper (220 and 400 grit) and sanding block
Q-Tip or wood dowel for spreading glue inside tubes
The Fin Shape Science Experiment Kit is another fine product
from:
Colorado Springs, Colorado USA
web site: www.ApogeeRockets.com
Kit #00524
Qty
Page 1
©2017, Apogee Components, Inc.
1
6
1
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 00524 and is the answer not in the manual?

Questions and answers

Summary of Contents for Apogee 00524

  • Page 1 Shark Fin Sheet (Balsa) 15602 Plywood Ring Set (Fin Shape Science) 19468 PNC-33mm (BT-55) 24043 Crimped Engine Hook 29124 Apogee 12” Plastic Parachute Pack 29519 100# Kevlar X 6 ft 29600 Clay mass - 5 grams 29610 Small Screw Eye 31133...
  • Page 2 Fin Shape Science Rocket Assembly Glue 1. Remove the parts for the fin alignment (both sides) fixture from the cardboard sheet. Dry as- semble the parts as shown. Make sure the tabs on the cross pieces protrude through the side plates. Apply a bead of wood glue over the tabs on both sides of the tool.
  • Page 3 7. Sand off the little nubs of paper on the ends of the tubes using medium grit sandpa- per and a sanding block. 8. Slide the fin alignment fixture onto one of the 4 inch (101mm) long body tubes. Test one set of fins into the fixture. Position the bottom edge of the fins on one edge of the tube.
  • Page 4 12. Locate the plywood centering ring without any notches on it. Using wood glue, attach it to the inside of one end of a red coupler. 13. Apply wood glue to the threads of the metal screw eye, and screw it into the plywood bulkhead.
  • Page 5 18. Glue the coupler with the screw eye into the 3 inch payload tube (the one with the small holes in the middle. It is positioned so it sticks out half way as shown. 19. Pass the yellow shock cord out the rear of the engine mount tube so it stays out of the way.
  • Page 6 24. Fold the parachute and insert it into the rocket along with the shock cord. Tem- porarily place one of the assembled fin-cans over the engine mount and exposed end of the tube coupler. DO NOT GLUE! NO Glue 25. Roll a piece of paper and insert it into the back of the rocket to hold the model while you paint it.
  • Page 7 C. Crumple and insert three sheets of recovery wadding into the body tube. D. Fold the parachute and insert it into the tube with the shock cord. Then insert the nose and payload section onto the tube. Fold Peak E. Insert the rocket motor into the aft end Down of the rocket by bending the clip back slightly Spike...
  • Page 8 Before cutting the balsa, be sure to orient the fin pattern so that the wood grain aligns. This will make the strongest fin that is hard to snap off. © 2017, Apogee Components, Inc. Page 8...
  • Page 9 Fin Shape Science Data Sheet Date: Weather Conditions: Time: Flight Empty Wt Fin Shape Engine Used Altitude Max Speed Number of rocket p/n 31135 Page 9...
  • Page 10 Suggestions for Your Fin Shape Science Experiment How to Eliminate all the Variables That Could Affect Performance The critical part of any science experiment is to eliminate time so any extra length of tape won’t change the mass of all that variables that could affect the results except the the rocket.