Advertisement
Quick Links
USA
SERVICE OFFICE
Dometic Corporation
509 South Poplar Street
Lagrange, IN 46761
260-463-4858
CANADA
Dometic Distribution
866 Langs Drive
Cambridge, Ontario
CANADA N3H 2N7
519-653-4390
For Service Center
Assistance Call:
800-544-4881
SERVICE INSTRUCTIONS
REVISION
Form No.3105903.060 8/04
(Replaces 3105903.052)
(French 3108577.044)
©2004 Dometic Corporation
LaGrange, IN 46761
REPLACEMENT INSTRUCTIONS FOR
828XXXX, 830XXXX, 833XXXX,
834XXXX, 836XXXX SERIES
MODEL 8300 AND SUNCHASER AWNINGS
FABRIC
ROLLER TUBE
This manual must be read and un-
derstood before installation, ad-
justment, service, or maintenance
is performed. This unit must be in-
stalled by a qualified service tech-
nician. Modification of this product
can be extremely hazardous and
could result in personal injury or
property damage.
"More information https://www.caravansplus.com.au"
Lire et comprendre ce manuel avant de
procéder à l'installation, à des réglages,
de l'entretien ou des réparations.
L'installation de cet appareil doit être
effectuée par un réparateur qualifié.
Toute modification de cet appareil peut
être extrêmement dangereuse et
entraîner des blessures ou dommages
matériels.
828(XXXX)
830(XXXX)
1
TORSION ASSEMBLY
MODELS
834(XXXX)
836(XXXX)
833(XXXX)
Advertisement
Related Manuals for Dometic A&E Systems 828 Series
Summary of Contents for Dometic A&E Systems 828 Series
- Page 1 Assistance Call: property damage. matériels. 800-544-4881 MODELS 828(XXXX) 834(XXXX) SERVICE INSTRUCTIONS 830(XXXX) 836(XXXX) 833(XXXX) REVISION Form No.3105903.060 8/04 (Replaces 3105903.052) (French 3108577.044) ©2004 Dometic Corporation LaGrange, IN 46761 “More information https://www.caravansplus.com.au"...
-
Page 2: Safety Instructions
This kit accidents and injuries. must be installed by a Dometic Service Cen- ter or a qualified service technician. Modifica- RECOGNIZE SAFETY INFORMATION tion of this product can be extremely hazard- ous and could result in personal injury or property damage. - Page 3 8300 and Sunchaser Service Instructions 5. To keep the awning from unwinding be sure the lock 2. Remove the screws securing the awning fabric at lever is in the roll down position and a nail inserted each end of the awning rail. See FIG. 1. in each torsion assembly for positive locking of the roller tube.
- Page 4 8300 and Sunchaser Service Instructions 7. With one person grasping each support arm, keep- B. Removal Of Torsion Assembly From Roller ing the two arm assemblies PARALLEL to each Tube other to avoid excessive twisting and possible dam- age to assembly, walk the awning out of the awning 1.
- Page 5 8300 and Sunchaser Service Instructions 2. The awning is installed on the coach. 7. Dometic requires the use of the end cap guide to a. This is the method used when replacing torsion prevent damages to the fabric, when replacing the or main arm.
- Page 6 8300 and Sunchaser Service Instructions 2. Installation of a new roller tube may require a notch 5. Mark the location of rivet holes in the end cap on cut in the side of the groove away from lock lever for rollertube.
- Page 7 8300 and Sunchaser Service Instructions i t i FIG. 14 FIG. 15 FIG. 16A RIGHT-HAND END CAP “A” Fabric without hemmed edge Cut Poly Rope flush with end of tube See Fig. 11 Trim Poly Rope Open leaving sufficient Groove length to tuck in place behind the open groove...
- Page 8 8300 and Sunchaser Service Instructions RIGHT-HAND FIG. 16B END CAP “A’ Fabric edge folded and Place open notch in alignment hemmed with fabric groove Cut Poly Rope flush with end of tube See Fig. 11 Trim Poly Rope Open leaving sufficient Groove length to tuck in place behind the...
- Page 9 8300 and Sunchaser Service Instructions FIG. 16E RIGHT-HAND END CAP “C” Fabric without hemmed edge Place open notch in alignment with fabric groove Cut Poly Rope flush with end of tube See Fig. 11 Trim Poly Rope Open leaving sufficient Groove length to tuck in place behind the...