Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Look 795 BLADE RS 2019
Summary of Contents for Look 795 BLADE RS 2019
- Page 1 NUAL BLADE RS...
-
Page 2: Table Of Contents
> 4 CONGRATULATIONS ! > 4 IMPORTANT INFORMATION > 5 INTRODUCTION TO THE PRODUCT PRE-ASSEMBLY CHECK > 5 FULL 795 BLADE RS ROUTING > 5 Rear derailleur hanger > 5 > 5 Mechanical/electronic routing configuration > 6 Routing assembly > 8 End cap/guide liner >... - Page 3 000 13756 GAINE FREIN-DI2 All information contained on this drawing is property of LOOK CYCLE INTERNATIONAL. Its reproduction for any use in any way or for commercial purpose is forbidden. All rights on this material are reserved. Nature de la modification...
- Page 4 MAIN ROUTING OPTIONS CONFIGURATION A CONFIGURATION B Frame routing mechanical / rim configuration Frame routing mechanical / disc configuration Non utilisé dans cette configuration Not use in this configuration Dérailleur arrière Rear derailleur Dérailleur arrière Rear derailleur Dérailleur avant Front derailleur Dérailleur avant Frein arrière Front derailleur...
-
Page 5: Congratulations
CONGRATULATIONS ! You have chosen the LOOK 795 BLADE RS. Thank you for putting your trust in our products. By choosing this new LOOK kit, you get the advantages of a high tech, French designed product. Your frame and its LOOK peripherals, which are identical to those provided to the big professional teams, are checked throughout their manufacture and will give you complete satisfaction. -
Page 6: Introduction To The Product
Patent No. FR1855814, guarantee the best traction allow either electronic or mechanical groupsets due to the strut deformation management, which to be used. Consult your LOOK dealer for the list increases the efficiency of your 795 BLADE RS. of compatible groupsets. -
Page 7: Routing Assembly
ROUTING ASSEMBLY Open the pages for Figures 1-2 at the beginning of the leaflet and 3-4-5-6 at the end of the leaflet. MECHANICAL ROUTING CONFIGURATION: A (RIM) AND B (HYDRAULIC) 1 / Remove the derailleur end cap (F) be careful 7 / If you route your bike for a hydraulic system, then not to pull on the black liners. - Page 8 ROUTING ASSEMBLY ELECTRONIC ROUTING CONFIGURATION: C (RIM) AND D (HYDRAULIC) 1 / Remove the derailleur end cap (F). it out at branch 12 (Fig . 1), if the brake caliper and its hose are pre-routed then go through the hole 2 / Remove the two black mechanical routing liners at branch 12 (Fig.
-
Page 9: End Cap/Guide Liner
END CAP Fig. 7 End cap Rear derailleur liner Front derailleur liner Derailleur cables End caps Derailleur liners M5 square nut FHC M5x12 Screws - HEX 3mm Allen (tighten to 2 Nm) Passing the brake liner (hydraulic system) If you need to replace an end cap the procedure 1 / Place liners 2 and 3 in the caps in their channels to use is as follows (the liner is fitted before (Fig. -
Page 10: Hood Assembly
All information contained on this drawing is property of LOOK CYCLE INTERNATIONAL. Its reproduction for any use in any way or for commercial purpose is forbidden. All rights on this material are reserved. -
Page 11: Removable Hub
REMOVABLE HUB Frame ASSEMBLY Retaining 1 / Make sure that the end cap is in the open spring position. 2 / Place the cap in its housing, against the composite wall of the frame. 3 / Tighten the tensioner to 1 Nm until the cap is fully seated in its housing (Fig. -
Page 12: Headset
HEADSET NOTE: For the complete assembly of the LOOK headset, it is highly recommended that you contact your authorised LOOK dealer. Fig. 11 Junction spacer Compression ring 1 1/2" (36° - 45°) bearing Hole for the brake hose (disc version) -
Page 13: Expander
EXPANDER With your 795 BLADE RS you will find a factory assembled expander developed specifically for the 795 BLADE RS pivot. Fig. 12 Cap - HEX 6mm Allen - max 12 Nm Fixing screw - HEX 5 mm Allen - 7 to 8 Nm Upper cone Locking rim (x2) O ring... -
Page 14: Aeropost 2 Seat Post
AEROPOST 2 SEAT POST Fig. 14 AEROPOST 2 tube Comfort elastomer Short offset head Long offset head (optional) N° Désignation Head fixing screw (x2) - TORX T25 - 4 Nm + Tube de selle AEROPOST 2 Elastomère de confort LOCTITE 243™ Tête court déport Tête long déport (optionelle) Domed washer for screws (x2) -
Page 15: Fitting Of The Shimano Battery In The Seat Post
AEROPOST 2 SEAT POST IMPORTANT: Your AEROPOST 2 seat post is not compatible with oval rail saddles with rails taller than 9.6mm. REMOVAL of the saddle To remove the saddle, or to adjust its position : unscrew by a few turns the lower flanges' screw. Apply a slight force to the front and back of the saddle alternately to loosen the flanges on the seat post. -
Page 16: Check The Seat Post Is Inserted The Minimum Amount
AEROPOST 2 SEAT POST With your 795 BLADE RS you will find a factory assembled expander developed specifically for the 795 BLADE RS pivot. Fig. 17 Rear flange Front flange Fixing screw – HEX 4 mm Allen - 10 Nm + grease O ring Washer NOTE : If there is any noise when... -
Page 17: Cut The Aeropost 2 Seat Post
AEROPOST 2 SEAT POST Cutting the AEROPOST 2 seat post IMPORTANT: Before cutting your seat post, check that the minimum insertion is has been met. Your AEROPOST 2 seat post gives you the option Fig. 18-1 to cut it according to the cutting instructions marked on your seat post (Fig. -
Page 18: Adjustment Of The Saddle Setback
AEROPOST 2 SEAT POST Adjustment of the saddle setback The AEROPOST 2 comes fitted with a rearward facing short offset head. If required, you can turn this part to the front or use the long offset version (not supplied with the bike). To adjust the saddle setback: 1 / remove your saddle from the seat post (see §... -
Page 19: Rear Hydraulic Brakes
BRAKE ASSEMBLY Rear hydraulic brakes IMPORTANT : There are two assembly options, the first is an assembly in which the hose is not connected to the caliper, whereas in the second the hose is pre-connected to the caliper. NOTE : Your bike in the disc version is provided with 140/160 mm FLAT MOUNT standard compatible fixing front and rear. -
Page 20: Bottom Bracket
TOKEN box suited or paralysed. to the standard of your crankset, it is strongly recommended you go to your nearest LOOK For further information on maintenance re- dealer for more of information. quirements, please visit www.lookcycle.com LOOK WARRANTY POLICY section >... -
Page 21: Guarantee
(1) for a period of two years (2) from guarantees, a free lifetime warranty on LOOK bike the date of purchase. frames and forks. - Page 22 Ref. : 00021957 lookcycle.com...