Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Festo EGSC-BS-KF
Summary of Contents for Festo EGSC-BS-KF
- Page 1 Mini slide EGSC-BS-KF Operating instructions 8067130 2016-12 [8067132]...
- Page 2 Text designations: • Activities that may be carried out in any order 1. Activities that should be carried out in the order stated – General lists è Result of an action/References to more detailed information Festo – EGSC-BS-KF – 2016-12...
-
Page 3: Table Of Contents
............Festo – EGSC-BS-KF – 2016-12 English... -
Page 4: About This Document
EGSC-BS-KF About this document For all available product documentation è www.festo.com/pk The mini slide EGSC-BS-KF is designated as product in these operating instructions. Read the operating instructions carefully before starting all work on the product. Safety Safety Instructions • Observe product labelling. -
Page 5: Service
EGSC-BS-KF Service Contact your regional Festo contact person if you have technical questions: è www.festo.com. Product overview Function A rotating ball screw converts the rotation of a motor into straight-line motion. As a result, the slide 5 moves backwards and forwards. The slide is ball bearing guided. The reference position of the carriage can be determined using proximity sensors (è... -
Page 6: Transport
When de-energised, the slide can move or fall to the lower end position in an uncontrolled manner. Injury due to impacts or pinching. • Bring moving parts of the product into a safe end position or secure them against falling. Festo – EGSC-BS-KF – 2016-12 English... -
Page 7: Mounting
EAHF-L2 1) Accessories è www.festo.com/catalogue. Fig. 5 • Select mounting components according to the hole pattern è www.festo.com/catalogue. • Mount the mounting components outside the positioning range to prevent collisions. • Mount the mini slide. • Tighten screws evenly. -
Page 8: Attachment
• Precisely adjust the additional guide and mini slide or use a connection that enables a tolerance compensation. The guide is not overloaded in this manner. Fig. 8 Size Screw Max. screw-in depth D [mm] Tightening torque [Nm] Centring H7 [mm] Tab. 2 Festo – EGSC-BS-KF – 2016-12 English... -
Page 9: Mounting Accessories
9 è Assembly instructions of the accessories. Fig. 9 Avoidance of contamination • Connect sealing air. To do so, remove the filter element 4 from the housing and connect the compressed air/vacuum. Fig. 10 Festo – EGSC-BS-KF – 2016-12 English... -
Page 10: Commissioning
– Travel speed – Moving mass – Mounting position • Use the Festo “PositioningDrives” engineering software to design the spindle axis è www.festo.com. Note Block-shaped acceleration profiles (without jerk limitation) cause high peaks in the drive force that can lead to an overloading of the drive. Due to overshooting effects, positions outside of the permissible range may also occur. - Page 11 After a successful test run, the slide is ready for operation. Tab. 3 Size Max. impact energy 0.005 0.009 0.014 0.044 1) Max. speed of the homing procedure for all sizes: 0.01 m/s Tab. 4 Festo – EGSC-BS-KF – 2016-12 English...
-
Page 12: Service
• Observe information on transport è 6 Transport. • Remove motor cables and mounting components. Disposal • Dispose of the packaging and slide at the end of the production service life according to the valid provisions for environmentally sound recycling. Festo – EGSC-BS-KF – 2016-12 English... -
Page 13: Fault Clearance
The reversing backlash is Wear Exchange the mini slide. too large (è 9 Service). The no-load torque increases. Slide travels over end Proximity sensor does not Check proximity sensor, connections and position. switch. control system. Tab. 5 Festo – EGSC-BS-KF – 2016-12 English... -
Page 14: Technical Data
| Fy | | Mx | | Mz | | Fz | fv + 1) The “PositioningDrives” engineering software is available for sizing tasks è www.festo.com/sp. 2) Measured at a speed of 0.05 m/s. Tab. 6 Festo – EGSC-BS-KF – 2016-12 English... - Page 15 Materials Profile, slide Anodised aluminium Guide, screws, ball bearing, spindle Steel Covers PA, NBR Weight Zero stroke length [kg] 0.176 0.327 0.608 1.549 Per 100 mm stroke [kg] 0.186 0.305 0.629 1.956 Tab. 7 Festo – EGSC-BS-KF – 2016-12 English...
- Page 16 Copyright: Festo AG & Co. KG Ruiter Straße 82 73734 Esslingen Germany Phone: +49 711 347-0 Fax: +49 711 347-2144 Reproduction, distribution or sale of this document or communica E-mail: tion of its contents to others without express authorization is service_international@festo.com...
Need help?
Do you have a question about the EGSC-BS-KF and is the answer not in the manual?
Questions and answers