Operation; Software Function Chart - Reloop BeatMix Instruction Manual

4. OPERATION

4.1 Software Function Chart

NO BEZEICHNUNG
T1 Pitch Fader
Adjusts the current deck's pitch (see -T13-).
T2 Effect Change
By turning the effect can be changed in the respective deck.
T3 Effect Parameter 2
By turning the effect parameter 2 can be manipulated
T4 Filter
Regulates the channel filter. By turning the dial to the left, a low-pass filter will be carried
out; by turning to the right, a hi-pass filter will be carried out.
T5 Loop Length
By turning the encoder the length of a set loop can be varied. By pushing the encoder
an automatic loop with the adjusted length will be set without the need to set a loop-out
point manually.
T6 FX On Button
Activates the selected effect in the respective deck.
T7 Beat Mash Button
Activates the integrated beat mash effect, even if another effect is loaded.
T8 Auto Loop Beginning
Sets a quantized loop for the set loop length.
T9 Monitor-CUE Button
Via this button the selected deck can be monitored.
T10 Jog Mode: Scratch
When active, it is possible to scratch within a track with the Jog Wheel.
T11 Jog Mode: Search
When active, you can fast-search within a track. If none of these modes should be active,
you can pitch bend with the jog wheel.
T12 Jog Wheel
See -T10- and -T11-.
T13 Pitch Bend Buttons
You can emulate braking or push-start a track.
T14 Shit Button
By pressing this button all the device's control elements obtain another assignment. The
current assignment can be seen on the right side of this chart.
T15 Hot Cue Buttons
With these the 4 hot cues of a track can be controlled. If a hot cue is not assigned (no LED
feedback), it will be asigned to the current track position by clicking the button -T13-.
T16 Sync Button
The current track's tempo will be synchronised to the master deck. By pressing again the
beat phases will be matched.
T17 Cup Button
Returns to the last set cue point and restarts playback from there.
T18 Cue Button
When the deck is in play mode, the track will return to the last set cue point. By pressing
again playback will start as long as the button is being held. If the deck is in oause mode a
new cue point will be set at the current position.
T19 Play/Pause Button
Starts and pauses a track's playback.
T20 Gain Dial
With this dial the input gain of the respective deck can be adjusted.
T21 EQ Dial
With this dial the hi/mid/low frequencies can be adjusted.
T22 Load Button
By presing this button the selected track will be loaded into the respective deck.
T23 Master Volume
With this dial the master volume can be adjusted. This dial is analog and does not send
MIDI signals.
T24 Headphones Volume
With this dial the headphones' volume can be adjusted. This dial is analog and does not
send MIDI signals.
After the Reloop Beatmix has been properly connected and correctly configured in the DJ software it can now be used.
18
SURFACE
SHIFT BEZEICHNUNG
Sample Change
By turning the sample in the respective deck can be
changed.
Sample Volume
By turning the sample volume can be adjusted.
Loop Adjustment
Moves the loop in a bar.
Sample On Button
Activates the selectes sample in the respective deck.
Loop-In
Sets a loop-in point.
Loop-Out Button
Sets a loop-out point. The loop is nopw activated.
Beat Jump Buttons
By pushing the playmarker in a track jumps forward or
backward respectively by a beat.
Delete Hot Cue
When pressing a hot cue in shift mode, the hot cue will
be deleted.
Track Beginning Button
by pressing the track will return to its beginning and
the deck will stop.
TAP Button
By pressing rhythmically thdeck's tempo can be
determined.
Fader Start Button
By pushing the fader up you can start the track from
the set cue point. By pulling the fader back to the zero
position the track will return to the set cue point.
Keylock
Turns the keylock function on/off.
View Button
You can switch between various views such as browser,
effects, sampler and record.