Table of Contents
Related Manuals for Z GRILLS ZPG-7002B
Summary of Contents for Z GRILLS ZPG-7002B
- Page 1 WOOD PELLET GRILLS ZPG-7002B/ZPG-7002BPro/ZPG-7002E OWNER’S MANUAL MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS EMAIL: support@zgrills.com WEBSITE: www.zgrills.com VN082020...
-
Page 3: Table Of Contents
CONTENTS IMPORTANT SAFETY INFO COMPONENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Z GRILLS SUPPORT 3-Y LIMITED WARRANTY... - Page 4 SAVE THIS MANUAL FOR FUTURE REFERENCE...
-
Page 5: Important Safety Info
IMPORTANT SAFETY INFO GENERAL WARNINGS Please read this entire manual before installation and use of the pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. - Page 6 DO NOT place anything heavy on top of hopper lid. It is not a shelf and is a tip hazard. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or ‘freshen up’ a fire in this appliance. Keep all such liquids well away from the appliance when in use.
- Page 7 There is no guarantee that other brands of pellets are suitable for use in Z GRILLS. And Z GRILLS assumes no liability for any loss, damage or injury caused by the use of any other brands of pellets.
-
Page 8: Component List
COMPONENT LIST ITEM DESCRIPTION ITEM DESCRIPTION Grill Chamber Assembly Auger Drive Motor Name Plate Auger Tube Bushing Hopper Assembly I Power Cord Body Frame Thick Gasket Heat Baffle Cable Clip Grease Drain Pan Auger Warming Rack Hot Rod (Ignitor) Porcelain Cooking Grates Firepot Assembly Burner Box Assembly Hinge Assembly... - Page 9 HARDWARE PACKAGE LIST ITEM DESCRIPTION ITEM DESCRIPTION Screwdriver Gasket (Ø4.2*Ø12*1.0mm) Spring Washer Bolt 5/32-32*5 (Ø8.5*Ø13*2mm) Open End Wrench Bolt 1/4-20×12 Gasket (Ø13*Ø25*2.0mm) Gasket (Ø8.5*Ø25*2mm) Hexagon Bolt 1/4-20×12 Gasket (Ø6.5*Ø15*1.0mm) Bolt 5/32-32×6 Gasket (Ø6.5*Ø18*2mm) Hexagon Kep Nut 5/32-32 Cap Nut 5/16-18 Spring Washer Hexagon Nut 1/4-20 (Ø6.5*Ø10*1.2mm)
-
Page 10: Assembly Instructions
ASSEMBLY INSTRUCTIONS PARTS DIAGRAM HOPPER BURNER ASSEMBLY... - Page 11 Lid Assembly: 1.Using a screwdriver to remove the screws and gaskets that have been assembled in the Chamber. 2.Using the screws and gaskets to assemble the Lid as shown in the original position. Adjust the Lid in the middle position of the Chamber and tighten the screws. BODY FRAME ASSEMBLY...
- Page 12 1.MOUNTING THE BODY FRAME TO THE CHAMBER 1.With the help of another person, carefully place the Grill Chamber on a piece of carboard. Attach the 2 Left Legs (37) by inserting them into the base of the Grill Chamber Assembly (1) and attaching using Bolts (C), Spring Washer (P) and Gasket (M).
- Page 13 2.ASSEMBLING OF HOPPER Insert Hopper Assembly II (44) into Hopper Assembly I (3), align the holes. Insert the Bolts (N) through the holes in the Hopper and Hexagon Kep Nuts (O), then open the Hopper Lid and tighten it from inside. The four sides are installed in the same way. 3.Installation instructions for RTD Temperature Probe 1.Remove the screws from the left plate of the grill chamber.
- Page 14 4.MOUNTING THE HOPPER TO THE CHAMBER 1.Remove the 4 Gaskets and 4 Bolts from the Hopper, open the Lid, insert the Hopper into the square hole in the Chamber. Attach the 4 Gasket and 4 Bolts that were removed from the Hopper.
- Page 15 6.INSTALLING THE CHAMBER HANDLE TO LID 1.Insert the Bolts (E) through Gasket (F) and Lid (9) and into the Lid Handle (12). 2.Using the Wrench (K) to tighten. (Do not over tighten) 7.ATTACHING THE SMOKE STACK AND CHIMNEY CAP Insert two Bolts (E) through the two holes in the Smoke Stack Assembly (15) and the two holes in the Smoke Stack Gasket (16).
- Page 16 8.ATTACHING THE HEAT BAFFLE Attach the Heat Baffle (5) by locating the brackets on the front and back of the Grill Chamber Assembly (1). If properly positioned the Heat Baffle (5) should not move left to right. 9.ATTACHING THE GREASE DRAIN PAN Attach the Grease Drain Pan (6) over the Heat Baffle (5).
- Page 17 10.ATTACHING THE COOKING GRATE AND WARMING RACK Attaching the Porcelain Cooking Grate (8) and Warming Rack (7) in the chamber. 11.HANG ON THE GREASE BUCKET Hang the Grease Bucket (17) on the Grease Drain Tube.
-
Page 18: Initial Firing Instructions
Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. -
Page 19: Subsequent Start-Up
Temperature Dial to any cooking setting desired. 5.If this step is not successful, see TROUBLESHOOTING or contact Z GRILLS Technical Support to help diagnose the problem. -
Page 20: Operating Tips
OPERATING TIPS 1.Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open. -
Page 21: Maintenance & Cleaning
2.It is highly recommended that you use Z GRILLS Cover to protect your grill . 3.You can use a high-quality car wax on the outside surfaces of your grill to protect it’s finish. - Page 22 Clean the ash from the interior of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF, UNPLUGGED AND COLD BEFORE ATTEMPTING TO CLEAN ASH FROM THE GRILL.
-
Page 23: Troubleshooting
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Potential Problem Solution Cause Make sure the power cord is plugged Power in. Verify there is power at the electrical outlet. - Page 24 Pellets pellets. When contacting customer support Contact please have the following information Z GRILLS available: Your authorized Z Grills Customer dealer, your name, phone number, Get your new parts Service or your address, your Z Grill serial number and Z GRILLS part identification number.
-
Page 25: Digital Thermostat Control Wiring Diagram
DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM... -
Page 26: Z Grills Support
Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Dealer's name and date of purchase... -
Page 27: 3-Y Limited Warranty
Z GRILLS, Inc. shall not be liable if you install, operate, clean or maintain your grill without following the owners' manual instructions. Misuse, abuse, alteration and natural disasters...