Sony DVP-S525D Operating Instructions Manual page 52

Settings for Sound (AUDIO SETUP)
Notes
• When you play the sound tracks with 96 kHz sampling
frequency, the output signals from the DIGITAL OUT
(OPTICAL, COAXIAL) are converted to 48 kHz (sampling
frequency). When the signals are output from LINE OUT
(AUDIO) connectors, sampling frequency stays at 96 kHz and
the output signals are converted to analog signals.
• When you select "OFF," you cannot set "DOLBY DIGITAL,"
"MPEG" and "DTS."
Setting for the Signal to the Digital
Output
When you select "ON," set "DOLBY DIGITAL," "MPEG"
and "DTS."
Switches the methods of outputting audio signals when
you connect a digital component such as a receiver
(amplifier) having a digital connector, an audio
component having a built-in DTS decoder, a DAT or MD
via the DIGITAL OUT OPTICAL or COAXIAL connector
using an optical or coaxial digital connecting cord. For
details on the connection, see page 12.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
TRACK SELECTION:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
DTS:
To set, press , then
To quit, press .
SETUP
pDOLBY DIGITAL
Selects output Dolby Digital signals via the DIGITAL OUT
OPTICAL and COAXIAL connectors. You cannot select
this item when you set "DIGITAL OUT" to "OFF."
• D-PCM (Downmix PCM): when you play the Dolby
Digital sound tracks, the output audio signals are mixed
down to 2 channels. With the settings of the item
"DOWN MIX" in "AUDIO SETUP," you can select
whether the signals conform to Dolby Surround (Pro
Logic) or not.
• DOLBY DIGITAL: when the player is connected to an
audio component with a built-in Dolby Digital decoder.
Note
If the player is connected to an audio component lacking a
built-in Dolby Digital decoder, do not set "DOLBY DIGITAL"
in "AUDIO SETUP" to "DOLBY DIGITAL." Otherwise, when
you play the Dolby Digital sound track, a loud noise or no
sound will come out from the speakers, affecting your ears or
causing the speakers to be damaged.
52
OFF
STANDARD
OFF
DOLBY SURROUND
ON
D-PCM
PCM
OFF
.
ENTER
pMPEG
Selects output MPEG AUDIO signals via the DIGITAL
OUT OPTICAL and COAXIAL connectors. You cannot
select this item when you set "DIGITAL OUT" to "OFF."
• PCM: when the player is connected to an audio
component lacking a built-in MPEG decoder. If you
play MPEG AUDIO sound tracks, the player outputs
stereo signals taken from MPEG AUDIO signals via the
DIGITAL OUT OPTICAL and COAXIAL connectors.
• MPEG: when the player is connected to an audio
component having a built-in MPEG decoder.
Note
If the player is connected to an audio component lacking a
built-in MPEG decoder, do not set "MPEG" in "AUDIO
SETUP" to "MPEG." Otherwise, when you play the MPEG
AUDIO sound track, a loud noise will come out from the
speakers, affecting your ears or causing the speakers to be
damaged.
Note
The player outputs the MPEG analog audio sound only from the
front speakers when you set "DIGITAL OUT" in "AUDIO
SETUP" to "ON" and then set "MPEG" to "MPEG."
pDTS
Selects output DTS signals via the DIGITAL OUT
OPTICAL and COAXIAL connectors. You cannot select
this item when you set "DIGITAL OUT" to "OFF."
• OFF: when the player is connected to an audio
component lacking a built-in DTS decoder.
• ON: when the player is connected to an audio
component having a built-in DTS decoder.
Note
Select the setting correctly. Otherwise, no sound or strange
sound will come out from the speakers, affecting your ears or
causing the speakers to be damaged.
• Do not play the DTS sound tracks without
connecting the player to an audio component
having a built-in DTS decoder. You cannot hear
the DTS sound unless you connect the player to
an audio component having a built-in DTS
decoder.
• When you play the DTS sound track on a CD, a
loud noise may come out from the LINE OUT
(AUDIO), 5.1CH OUTPUT and PHONES
connectors, affecting your ears or causing the
speakers or headphones to be damaged.
• When you play the DTS sound track on a DVD,
no sounds will come out from the LINE OUT
(AUDIO), 5.1CH OUTPUT and PHONES
connectors.