Changing The Setting Position Of Cloth; Changing Over The Mode Of The Start Switch; Changing Over The Presser Movement; Changing Over The Counter (Down Counting) - JUKI MEB-3810N Series Instruction Manual

9-2. Changing the setting position of cloth

The setting position of the material can be changed to the front side or the sewing start position in the case of
cut-after knife/without knife.
(1) To set the material setting position at the front side for every type of knife setting, i.e., cut-before knife/
cut-after knife/without knife.
1) Set memory switch No. 12 to "1".
2) Set the travel amount to this side using Memory switch No. 23. (Factory-set to 22 mm as standard at the time of shipment)
(2) To set the material setting position at the origin in the case of the cut-before knife, and at the sewing start
position in the case of the cut-after knife/without knife.
1) Set memory switch No. 12 to "2".
(3) To set the material setting position at the front side in the case of the cut-before knife, and at the sewing
start position in the case of the cut-after knife/without knife.
1) Set memory switch No. 12 to "3".
2) Set the travel amount to this side using Memory switch No. 23. (Factory-set to 22 mm as standard at the time of shipment)

9-3. Changing over the mode of the start switch

The presser comes down by the operation of the start switch only, and the sewing is continually performed.
Set memory switch No. 15 to "1".
It is also possible to perform the normal use by lowering the presser with the presser switch and
performing sewing with the start switch. However, the presser LED of the hand switch is always
put in the state of flashing on and off.

9-4. Changing over the presser movement

It is possible that the presser returns to the set position while it is held lowered after completion of sewing.
(The presser returns to the set position while it is raised after completion of sewing in the standard state of delivery.)
1) Set Memory switch No. 20 to "1" or "2".
❶ The presser foot goes up after the feed base returns to the material setting position when Memory switch
No. 20 is set to "1".
❷ The presser foot is lifted by means of the Presser foot switch after the feed base returns to the material
setting position when Memory switch No. 20 is set to "2".
2) The presser foot is kept lowered also when the feed base is brought back to the material setting position
by means of the Reset key
means of the Temporary stop switch.

9-5. Changing over the counter (DOWN counting)

Set the count value and perform DOWN counting. It is possible to prohibit the start at the count value "0".
■ Change-over to DOWN counter
1) Set memory switch No. 13 to 2.
2) When the count value reaches "0", the display flashes on and off and the Presser foot switch and the Start
switch are disabled.
3) Press RESET key
(State of standard delivery : initial value = 100)
In order to perform the start even when the count value becomes "0", set memory switch No. 14 to "0".
■ Setting the initial value of DOWN counter
It is necessary to set the initial value starting "Count DOWN" when using DOWN counter.
1) Press COUNTER key
2) Press RESET key
the state of standard delivery.
3) Set the count value by means of the –/BACKWARD key

9-6. Changing over to the mode of the stop before cloth cut

The sewing can be temporarily stopped before performing the cloth cutting operation at the time of the pattern
sewing of cut-after knife data.
1) Set memory switch No. 21 to "1". The sewing machine once stops after sewing and cloth cutting operation
is performed by again pressing the start switch.
It is also possible to return the sewing machine to the cloth set position without performing cloth cutting
operation by pressing RESET key
in such a case sewing is stopped before the end of sewing is reached by
and the count value returns to the initial value.
to display the counter.
to return the count value to the initial value.The initial value has been set to 100 in
.
or +/FORWARD key
− 76 −
.