Page 1
Change for life Wired Remote Controller XE71 (XE71-44/G) Owner's Manual Original Instructions Thank you for choosing our product. Please read this Owner’s Manual carefully before operation and retain it for future reference. If you have lost the Owner's Manual visit www.greecomfort.com/resources/dealer-resources-...
Page 2
User Notice ◆ Never install the wired remote controller in highly humid environments or expose to direct sunlight. Never drop, shake, toss or frequently disassemble the wired remote controller or the wireless ◆ remote controller. Never operate the wired remote controller and the wireless remote controller with wet hands. ◆...
Wired Remote Controller XE71 (XE71-44/G) Table 1 Symbols Description Swing function. Sleep function (Only sleep 1). Running modes of the indoor unit (Cooling, Dry, Fan and Heating). Defrosting function for the outdoor unit. Gate-control function. Lock function. High, middle, low or auto fan speed of the indoor unit.
Wired Remote Controller XE71 (XE71-44/G) 2.2 Function of the Touch Pad Buttons Table 2 Name Function Enter/Cancel Function selection and cancellation. ▲ ① Running temperature setting of the indoor unit, range:61~86°F(16~30℃). ② Timer setting, range:0.5-24 hr. ▼ Setting of the high/middle/low/auto fan speeds.
Wired Remote Controller XE71 (XE71-44/G) 3 Operation Instructions 3.1 On/Off Press On/Off to turn on the unit, press again to turn it off. Note: The state shown in Fig.4 indicates unit is “Off” after powering on. The state shown in Fig.5 indicates the unit is “On”...
Wired Remote Controller XE71 (XE71-44/G) Fig.6 3.4 Fan Setting In the “On”/”Off” state of the unit, press Fan and the fan speed of the indoor unit will change in the order shown in Fig.7. Middle High AUTO Enter/Cancel Mode Function...
Page 9
Wired Remote Controller XE71 (XE71-44/G) Fig. 8 Timer off Setting under the “On” State of the Unit Timer range: 0.5-24hr. Every press of ▲or ▼ will make the set time increased or decreased by 0.5hr. If either of them is pressed continuously, the set time will increase/ decrease by 0.5hr every...
Wired Remote Controller XE71 (XE71-44/G) 3.6 Swing Setting Swing On: Press Function under on state of the unit to activate the swing function. In this case, Swing Off: When the Swing function is on, press Function to enter the Swing setting interface, with blinking.
Wired Remote Controller XE71 (XE71-44/G) 3.7 Sleep Setting Sleep on: Press Function under on state of the unit till the unit enters the Sleep setting Sleep off: When the Sleep function is activated, press Function to enter the Sleep setting interface.
Wired Remote Controller XE71 (XE71-44/G) 3.8 Turbo Setting Turbo function: The unit at the high fan speed can realize quick cooling or heating so that the room temperature can quickly approach the setting value. In the Cooling or Heating mode, press Function till the unit enters the Turbo setting interface When the Turbo function is activated, press Function to enter the Turbo setting interface and then press Enter/Cancel to cancel this function.
Wired Remote Controller XE71 (XE71-44/G) 3.9 E-heater Setting E-heater (auxiliary electric heating function): In the Heating mode, E-heater is allowed to be Once the wired remote controller or the remote controller enters the Heating mode, this function will be turned on automatically.
Wired Remote Controller XE71 (XE71-44/G) 3.10 Blow Setting Blow function: After the unit is turned off, the water in evaporator of indoor unit will be automatically evaporated to avoid mildew. In the Cooling or Dry mode, press Function till the unit enters the Blow setting interface and then press Enter/Cancel to active this function.
Wired Remote Controller XE71 (XE71-44/G) 3.11 Other Functions (1). Lock Upon startup of the unit without malfunction or under the “Off” state of the unit, press ▲ and ▼ at the same time for 5s till the wired remote controller enters the Lock function. In this case, LCD displays .
Wired Remote Controller XE71 (XE71-44/G) (4). Selection of the Fan Speed go to the commissioning status, and then adjust the display in the temperature display area to 01 through the button “Mode” and adjust the setting of the fan speed, which comes to two options.
Page 17
Wired Remote Controller XE71 (XE71-44/G) Note:CN1 is 485 communication interface and it used for connecting the 4-core communication wire. These two needle stands(CN2、CN3) are used for connecting the smart zone controller. There is no sequence for these two needle stands. You can connect one or two needle stand(s) basing on the requirement.
Page 18
(integrated control system). “n” indicates the number of communication node address (programmable wired controller XE71). The complete system is composed of the smart zone controller, wired controller XE71 and communication cable. The wired controller XE71can support 16 communication node addresses at the most (n≤16).
Wired Remote Controller XE71-44/G cord and connection lines between the indoor and outdoor unit, with a minimum interval of 20cm, otherwise the communication of the unit will probably work abnormally. If the air conditioning unit is installed where is vulnerable to electromagnetic interference, ②...
Page 20
Wired Remote Controller XE71-44/G Table 4 Meaning of Each Error Error Error Error Error Code Code Return air temperature sensor open/short Drive board communication error circuited evaporator temperature sensor open/short Compressor overheating protection circuited Indoor unit liquid valve temperature sensor...
Page 21
GREE ELECTRIC APPLIANCES, INC. OF ZHUHAI Add: West Jinji Rd, Qianshan, Zhuhai,Guangdong, China, 519070 Tel: (+86-756) 8522218 Fax: (+86-756) 8669426 E-mail: gree@gree.com.cn www.gree.com 600005061061...