BenQ LU9915 Installation Manual
  1. Manuals
  2. Brands
  3. BenQ Manuals
  4. Projector
  5. LU9915
  6. Installation manual
BenQ LU9915 Installation Manual

BenQ LU9915 Installation Manual

Rs232 command control
Hide thumbs Also See for LU9915:
Table of Contents

Advertisement

Quick Links

Download this manual
Projector RS232 Command Control
Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LU9915 and is the answer not in the manual?

Questions and answers

Related Manuals for BenQ LU9915

Summary of Contents for BenQ LU9915

  • Page 1 Projector RS232 Command Control Installation Guide...

  • Page 2: Table Of Contents

    Table of Contents Introduction ............................. 3 Wire arrangement ................................ 3 RS232 pin assignment ..............................3 Connections and communication settings ..................4 RS232 serial port with a straight cable ........................4 Settings .................................. 4 RS232 via LAN ................................6 Settings .................................. 6 RS232 via HDBaseT ..............................

  • Page 3: Introduction

    Introduction The document describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands. Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for product functions.

  • Page 4: Connections And Communication Settings

    Connections and communication settings Choose one of the connections and set up properly before RS232 control. RS232 serial port with a straight cable D-Sub port (male or female) on a projector D-Sub 9 pin D-Sub 9 pin PC or laptop (male) (female) D-Sub 9 pin...
  • Page 5 Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected. Finish Serial port setup. Baud rate 9600 bps (It cannot be changed) Check the baud rate of the connected projector from its OSD menu. Data length 8 bit Parity check...

  • Page 6: Rs232 Via Lan

    RS232 via LAN RJ45 port on a projector PC or laptop LAN cable Settings Find the Wired LAN IP address of the connected projector from the OSD menu and make sure the projector and the computer are within the same network. Input 8000 in the TCP port # field.
  • Page 7 Finish Serial port setup. Baud rate 9600 bps (It cannot be changed) Check the baud rate of the connected projector from its OSD menu. Data length 8 bit Parity check None Stop bit 1 bit Flow control None...

  • Page 8: Command Table

    Command table  Available features differ by projector specification, input sources, settings, etc..  Commands are working if the standby power is 0.5W or a supported baud rate of the projector is set.  Uppercase, lowercase, and a mixture of both types of characters are accepted for a command. ...
  • Page 9 Write Presentation <CR>*appmod=preset#<CR> Write sRGB <CR>*appmod=srgb#<CR> Write Bright <CR>*appmod=bright#<CR> Write Living Room <CR>*appmod=livingroom#<CR> Write Game <CR>*appmod=game#<CR> Write Cinema <CR>*appmod=cine#<CR> Write Dicom SIM <CR>*appmod=dicom#<CR> Write Vivid <CR>*appmod=vivid#<CR> Write Standard <CR>*appmod=std#<CR> Write User1 <CR>*appmod=user1#<CR> Write User2 <CR>*appmod=user2#<CR> Write User3 <CR>*appmod=user3#<CR> Write ISF Day <CR>*appmod=isfday#<CR>...
  • Page 10 Write Gamma BenQ <CR>*gm=benq#<CR> Read Gamma Status <CR>*gm=?#<CR> Write Noise Reduction + <CR>*nr=+#<CR> Write Noise Reduction - <CR>*nr=-#<CR> Read Noise Reduction value <CR>*nr=?#<CR> Write Overscan Off <CR>*ov=off#<CR> Write Overscan Crop <CR>*ov=crop#<CR> Write Overscan Zoom <CR>*ov=zoom#<CR> Read Overscan Status <CR>*ov=?#<CR> Write Reset picture settings <CR>*picture=reset#<CR>...
  • Page 11 Write Color Green Offset + <CR>*goffset=+#<CR> Write Color Green Offset - <CR>*goffset=-#<CR> Read Color Green Offset value <CR>*goffset=?#<CR> Write Color Blue Offset + <CR>*boffset=+#<CR> Write Color Blue Offset - <CR>*boffset=-#<CR> Read Color Blue Offset value <CR>*boffset=?#<CR> Write Color Red Gain + <CR>*rgain=+#<CR>...
  • Page 12 Write Saturation Red - <CR>*satr=-#<CR> Read Saturation Red value <CR>*satr=?#<CR> Write Saturation Green + <CR>*satg=+#<CR> Write Saturation Green - <CR>*satg=-#<CR> Read Saturation Green value <CR>*satg=?#<CR> Write Saturation Blue + <CR>*satb=+#<CR> Write Saturation Blue - <CR>*satb=-#<CR> Read Saturation Blue value <CR>*satb=?#<CR> Write Saturation Cyan + <CR>*satc=+#<CR>...
  • Page 13 Picture Write White balance Red + <CR>*wbr=+#<CR> Settings : Source White Locked Balance Write White balance Red - <CR>*wbr=-#<CR> Read White balance Red value <CR>*wbr=?#<CR> Write White balance Green + <CR>*wbg=+#<CR> Write White balance Green - <CR>*wbg=-#<CR> Read White balance Green value <CR>*wbg=?#<CR>...
  • Page 14 Read Current H Position <CR>*hpos=?#<CR> Write Phase + <CR>*phase=+#<CR> Source Locked (analog source only) Write Phase - <CR>*phase=-#<CR> Read Current Phase <CR>*phase=?#<CR> Write Tracking + <CR>*tracking=+#<CR> Write Tracking - <CR>*tracking=-#<CR> Read Current Tracking <CR>*tracking=?#<CR> Write Sync level + <CR>*synclevel=+#<CR> Write Sync level - <CR>*synclevel=-#<CR>...
  • Page 15 Write PIP mode Off <CR>*pip=off#<CR> Write PIP HDMI <CR>*psour=hdmi#<CR> Write PIP DVI-D <CR>*psour=dvid#<CR> Write PIP COMPUTER/YPbPr <CR>*psour=RGB#<CR> Write PIP COMPUTER 2/YPbPr2 <CR>*psour=RGB2#<CR> Write PIP DisplayPort <CR>*psour=dp#<CR> Write PIP 3G-SDI <CR>*psour=sdi#<CR> Write PIP HDBaseT <CR>*psour=hdbaset#<CR> Read Current PIP source <CR>*psour=?#<CR> Write PIP position Top Left <CR>*pippos=tl#<CR>...
  • Page 16 Write Quick auto search off <CR>*QAS=off#<CR> Read Quick auto search status <CR>*QAS=?#<CR> Write Set test pattern Off <CR>*tp=off#<CR> Write Set test pattern White <CR>*tp=white#<CR> Write Set test pattern Black <CR>*tp=black#<CR> Write Set test pattern Red <CR>*tp=red#<CR> Write Set test pattern Green <CR>*tp=green#<CR>...
  • Page 17 Warping Write Set Active Warp to Keystone <CR>*warp=keystone#<CR> Laser On Write Set Active Warp to 4 Coners <CR>*warp=4corners#<CR> Write Set Active Warp to Rotation <CR>*warp=rotation#<CR> Write Set Active Warp to Pin/Barrel <CR>*warp=pinbarrel#<CR> Read Active Warp Status <CR>*warp=?#<CR> Write Warp Reset <CR>*warp=reset#<CR>...
  • Page 18 Decrease 4 Corners Bottom-Left-X Write Increase <CR>*4cblx=+#<CR> Read 4 Corners Bottom-Left-X Status <CR>*4cblx=?#<CR> 4 Corners Bottom-Left-Y Write Decrease <CR>*4cbly=-#<CR> 4 Corners Bottom-Left-Y Write Increase <CR>*4cbly=+#<CR> Read 4 Corners Bottom-Left-Y Status <CR>*4cbly=?#<CR> 4 Corners Bottom-Right-X Write Decrease <CR>*4cbrx=-#<CR> 4 Corners Bottom-Right-X Write Increase <CR>*4cbrx=+#<CR>...
  • Page 19 Read Blanking Bottom Status <CR>*bnkb=?#<CR> Write Blanking Left Decrease <CR>*bnkl=-#<CR> Write Blanking Left Increase <CR>*bnkl=+#<CR> Read Blanking Left Status <CR>*bnkl=?#<CR> Write Blanking Right Decrease <CR>*bnkr=-#<CR> Write Blanking Right Increase <CR>*bnkr=+#<CR> Read Blanking Right Status <CR>*bnkr=?#<CR> Edge Blending Write Edge Blending On <CR>*eb=on#<CR>...
  • Page 20 Edge Blending Black Level Top Write Decrease <CR>*ebbt=-#<CR> Edge Blending Black Level Top Write Increase <CR>*ebbt=+#<CR> Edge Blending Black Level Read TopStatus <CR>*ebbt=?#<CR> Edge Blending Black Level Write Bottom Decrease <CR>*ebbb=-#<CR> Edge Blending Black Level Write Bottom Increase <CR>*ebbb=+#<CR> Edge Blending Black Level Read Bottom Status <CR>*ebbb=?#<CR>...
  • Page 21 Edge Blending Black Level Green Write Increase <CR>*ebcg=+#<CR> Edge Blending Black Level Green Read Status <CR>*ebcg=?#<CR> Edge Blending Black Level Blue Write Decrease <CR>*ebcb=-#<CR> Edge Blending Black Level Blue Write Increase <CR>*ebcb=+#<CR> Edge Blending Black Level Blue Read Status <CR>*ebcb=?#<CR> Write Standby Settings-Network on <CR>*standbynet=on#<CR>...
  • Page 22 Write System reset <CR>*system=reset#<CR> Laser On Information Read Get Model Name <CR>*modelname=?#<CR> Any State Read Get Serial Number <CR>*sn=?#<CR> Read Get F/W Version <CR>*swver=?#<CR> Read Get BQ F/W Version <CR>*fwver=?#<CR> Read Get Active source <CR>*activesour=?#<CR> Source Locked Read Get Pixel clock <CR>*pixelclock=?#<CR>...
  • Page 23 Write Instant On-off <CR>*ins=off#<CR> Read Instant On Status <CR>*ins=?#<CR> Write Lamp Saver Mode-on <CR>*lpsaver=on#<CR> Write Lamp Saver Mode-off <CR>*lpsaver=off#<CR> Read Lamp Saver Mode Status <CR>*lpsaver=?#<CR> Write Projection Log In Code on <CR>*prjlogincode=on#<CR> Write Projection Log In Code off <CR>*prjlogincode=off#<CR> Read Projection Log In Code Status <CR>*prjlogincode=?#<CR>...
  • Page 24 Write number 2 lamp <CR>*lammd=num2#<CR> Write Single lamp (minimum) <CR>*lammd=single#<CR> Read Current Lamp status <CR>*lammd=?#<CR> Write Smart Eco mode <CR>*lampm=seco#<CR> Write Smart Eco mode(LampCare) <CR>*lampm=seco2#<CR> Write Smart Eco mode(IumenCare) <CR>*lampm=seco3#<CR> Write(雙燈) Dual Brightest <CR>* lampm =dualbr#<CR> Write(雙燈) Dual Reliable <CR>* lampm =dualre#<CR> Write(雙燈) Single Alternative <CR>* lampm =single#<CR>...
  • Page 25 BenQ.com © 2017 BenQ Corporation All rights reserved. Rights of modification reserved. Version: 1.00-S...

Table of Contents