Technical Specifications - Kärcher TB 36 Original Instructions Manual

Note
Set the date to 00.00.XX for unused public
holidays.
Language selection
Here you can select the language of the
display for the information menu.
Setting dosing pumps
1 Dosing pump shampoo
2 Dosing pump CTH (optional)
3 Dosing pump foam (option)
The dosing pumps dose the washing water
with the detergents in accordance with the
wash programme and the equipment of the
system.
Plant dimensions
Washing width*
Washing height, system with 3 brushes**
Washing height, system with 2 brushes
Free drive through width, setup/wheels
Free drive through clearance**
System width with rotating brushes*
System width with side spray protection***
System height**
System height with roof spray protection**
* can be reduced by 200 mm in one step
** can be reduced by 100 mm each in 3 steps
*** adaptable by +/- 200 mm, depending on the brush diameter (standard diameter 965 mm)
Features
Wash brushes
Diameter of side-brushes
Side
Side-brush rotation speed
Diameter of brush Roof
Brush rotation speed Roof
Portal drive speed
Sound pressure level L
pA
Uncertainty K
*System with high pressure side nozzles, with-
out vehicle to be cleaned
**System with high pressure roof bar and spin-
ner, with vehicle to be cleaned
Note
The dosage amount is optimally set by the
fitter when the system is installed. General-
ly no reset is necessary.
Set dosing amount
Caution
Risk of damage. Do not adjust the dosing
volume during system standstill.
1 Ventilation lever
2 Ventilation button
3 Adjustment knob dosing volume
 Switch on the dosing pump in manual
operation.
 Press the ventilation key repeatedly
and release it.

Technical specifications

Dimensions (for brush diameters of 965 mm)
Connection values of basic system
Electrical connection
mm 965... Voltage**
1165
1/min 129 Max. voltage fluctuation*** %
mm 965... Frequency
1165
Connection output Basic
1/min 129 plant
m/min 0...24 Pre-securing Control cabinet * A
dB(A) 79*/ * to be provided at installation site according to
75** the local requirements
**Supplying voltage by means of the generator
dB(A) 4*/3**
is prohibited
*** Voltage peaks must be within the permissible
voltage range
Water connection
Nominal width
TB 36
mm
mm 3600
mm 3600
mm
mm 3668
mm
mm
mm 4539
mm
V 400±10%/
3~, P, N
Hz
kW
Inch
7
-
EN
 Pull out the adjustment knob for the
dosing volume.
 Set the adjustment knob to the required
value.
 Release the ventilation key.
 Push in the adjustment knob for the
dosing volume.
Bleed dosing pump.
The compressed air supply of the system
must be operating.
 Turn the ventilation lever in an anti-
clockwise direction until it stops.
 Set the dosing volume to 100%.
 Press the ventilation key until the deter-
gent emerges from the ventilation line
at the bottom of the dosing pump with-
out bubbles.
 Set the dosing volume to the required
value.
 Turn the ventilation lever in a clockwise
direction until it stops.
TB 42 TB 46
2900
4250 4600
4155 4585
3540/3510
4318 4668
4830
5000
5189 5539
System height +58 mm
Flow pressure according to
DIN 1988 (with 100 l/min)
Temperature
Compressed air connection
Nominal width
5
Pressure
50
Supply capacity, min.
5,3
Use in frost protection
16
Consumption with foam, in-
tensive prespray (side and/
or roof)
1
TB 50
5050
4995
5118
5989
MPa 0,4...0,6
(bar) (4...6)
°C max. 50
Inch 1/2
MPa 0,6...0,8
(bar) (6...8)
I/min 100
I/min 500
I/min 500
9