Advertisement
TEcHNIcAl DATA
Rated input
Input voltage
No-load speed
Orbital travel diameter
Dimensions of grinding plate
Weight according EPTA-Procedure 01/2014
Noise/ Vibration information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 62841.
Vibration emission value a
h
Uncertainty K=
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 62841 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but
not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
WARNING! Read all safety warnings, instructions, illustrations
and specifications provided with this power tool. Failure to follow
all instructions listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
RANDom oRbITAl SANDER SAfETy WARNINGS
Hold the power tool by insulated gripping surfaces, because the
sanding surface may contact its own cord. Cutting a "live" wire may
make exposed metal parts of the power tool "live" and could give the
operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of control can
cause personal injury.
ADDITIoNAl SAfETy AND WoRkING INSTRUcTIoNS
Appliances used at many different locations including open air should
be connected via a residual current device of 30 mA or less.
Always wear goggles when using the product. It is recommended to
wear gloves, sturdy non slipping shoes and apron.
Always disconnect the plug from the socket before carrying out any
work on the product.
Only plug-in when product is switched off.
Keep mains lead clear from working range of the product. Always lead
the cable away behind you.
Before use check product, cable, and plug for any damages or material
fatigue. Repairs should only be carried out by authorised service
16
RANDom oRbITAl SANDER
agents.
The dust produced when using the product may be harmful to health
(e.g. when working oak or beech wood, stones, paint, which could
contain lead or other harmful chemicals). Do not inhale the dust. Use
a dust absorption system and wear a suitable dust protection mask.
Remove deposited dust thoroughly, e.g. with a vacuum cleaner.
Do not use machines on any material containing asbestos.
The product is suitable only for dry sanding.
Dust from certain paints, coatings, and materials may cause irritation
or allergic reactions.
Do not use compressed air to blow dust or debris. This practice is
dangerous and can cause dirt and grit to be blasted into someone's
eyes, causing serious injury.
RESIDUAl RISkS
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise and the operator should pay special attention to
avoid the following:
■
Contact with the grinding plate
Additional caution must be exercised to prevent operator's fingers
and hands from coming into contact with the grinding plate.
■
Contact with or inhalation of dust
While using the product, considerable dust and fine particles will
be produced. Use the dust collection device or connect a dust
extraction vacuum during use. Wear respiratory protection masks
containing filters appropriate to the materials being worked.
16
EX150ES
440 W
220-240 V
50 Hz
4000-10000 min
-1
3.2/ 6.4 mm (1/8"/ 1/4")
ø 150 mm
2.8 kg
86 dB(A)
97 dB (A)
8.5 m/s
2
1.5 m/s
2
■
■
RIS
It h
con
indi
of t
fact
prac
sym
pos
■
■
■
If yo
disc
use
take
Sp
This
can
and
scra
To
bac
them
Do
mA
Con
volt
sock
clas
AD
Onl
fast
mA
If th
man
Advertisement
