Advertisement
2
SPECIFICATIONS
Type
AC supply type
Model No.
CY-11
(Note)
Item
Sensing range
Sensing object
Power supply
24 to 240V AC
Power / Current
Emitter: 1.5VA or less
consumption
Receiver: 2.5VA or less
Response time
20ms or less
Operation indicator
Red LED (lights up when the output is ON)
Red LED (lights up when
Power indicator
the power is ON)
Emission indicator
Protection
-25 to +55
Ambient temperature
Storage: -30 to +70
Ambient humidity
35 to 85% RH, Storage: 35 to 85% RH
Emitting element
Weight
Emitter: 90g approx., Receiver: 100g approx.
Accessories
Note: The model No. with suffix 'P' shown on the label affixed to the
sensor is the emitter, 'D' shown on the label is the receiver.
(e.g.) Emitter: CY-11P, Receiver: CY-11AD
3
CAUTIONS
This product has been developed / produced for indus-
trial use only.
Make sure that the power supply is off while wiring.
Take care that wrong wiring will damage the sensor.
Verify that the supply voltage variation is within the rating.
If power is supplied from a commercial switching regu-
lator, ensure that the frame ground (F.G.) terminal of
the power supply is connected to an actual ground.
Do not run the wires together with high-voltage lines or
power lines or put them in the same raceway.
This can cause malfunction due to induction.
In case noise generating equipment (switching regula-
tor, inverter motor, etc.) is used in the vicinity of this
product, connect the frame ground (F.G.) terminal of the
equipment to an actual ground.
Do not use during the initial transient time (50ms) after
the power supply is switched on.
Extension up to total 100m, or less, is possible with
2
0.34mm
, or more, cable. However, in order to reduce
noise, make the wiring as short as possible.
Make sure that stress by forcible bend or pulling is not
applied directly to the sensor cable joint.
Take care that the sensor is not directly exposed to fluo-
rescent light from a rapid-starter lamp or a high frequency
lighting device, as it may affect the sensing performance.
This sensor is suitable for indoor use only.
The tightening torque should be 2N m or less.
The following items are required, as conditions for use
in order to conform to CE.
The output applied voltage should be the same as the
supply voltage of the sensor.
Be sure to add a short-circuit protection (a fuse or a
breaker) to the power supply input and the output.
DC supply type
CY-21
12m
8mm or more opaque object
+10
%
10 to 30V DC
-15
Emitter: 20mA or less
Receiver: 25mA or less
2ms or less
Red LED (lights up during
beam emission)
IP67 (IEC)
(No dew condensation or icing allowed)
Infrared LED (modulated)
Nut: 4 pcs.
4
CONNECTION
When using the pigtailed type, purchase the mating ca-
ble (optional).
Connecting
Put female and male connectors together
as the convex and the concave meet.
Hold one ring not to rotate and turn the
other ring clockwise until they become
tight.
Disconnecting
Turn the ring counterclockwise and
separate them.
5
BEAM ALIGNMENT
Placing the emitter and the receiver face to face along a
straight line, move the emitter in the up, down, left and
right directions, in order to determine the range of the
light received condition with the help of the operation in-
dicator (red). Then, set the emitter at the center of this
range.
Similarly, adjust for up, down, left and right angular
movement of the emitter.
Further, perform the angular adjustment for the receiver
also.
Sensing
object
Receiver
Operation indicator (Red)
6
INTENDED PRODUCTS FOR CE
MARKING
The models listed under '
come with CE Marking.
As for all other models, please contact our office.
Contact for CE
<Until June 30 ,2013>
Panasonic Electric Works Europe AG
Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany
<From July 1 ,2013>
Panasonic Marketing Europe GmbH Panasonic Testing Center
Winsbergring 15, 22525 Hamburg,Germany
http://panasonic.net/id/pidsx/global
Overseas Sales Division (Head Office)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: +81-568-33-7861 FAX: +81-568-33-8591
About our sale network, please visit our website.
© Panasonic Industrial Devices SUNX Co., Ltd. 2012
Concave
Convex
Fixing ring
Fixing ring
Emitter
2
SPECIFICATIONS'
PRINTED IN CHINA
Advertisement
