Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Siemens SIMOGEAR BA 2730
Summary of Contents for Siemens SIMOGEAR BA 2730
- Page 3 General information and ___________________ BA 2730 safety notes ___________________ Securing functional safety ___________________ SIMOGEAR EC Declaration of Conformity Geared motor with encoder for safety-relevant applications BA 2730 Operating Instructions Supplement to SIMOGEAR operating instructions BA 2030 and BA 2330 and for the operating instructions Sendix SIL Encoders for Functional Safety of the Kübler company Translation of the original instructions...
- Page 4 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 5: Table Of Contents
Table of contents General information and safety notes ...................... 7 General information ........................7 Copyright ........................... 8 Use for the intended purpose ....................9 Securing functional safety ........................11 General information ........................ 11 Unpacking ..........................14 Electrical installation of the encoder ..................15 Commissioning the encoder .................... - Page 6 Table of contents BA 2730 Operating Instructions, 08/2015, A5E36448105...
-
Page 7: General Information And Safety Notes
General information and safety notes General information Note Siemens AG does not accept any liability for damage and failures that result from the non- observance of these operating instructions. These operating instructions are included with the geared motor when delivered. Keep the operating instructions close to the geared motor. -
Page 8: Copyright
The described geared motors correspond to state-of-the-art technology at the time these operating instructions were printed. Siemens AG reserves the right to change individual components and accessory parts in the interest of further development. The changes serve to improve the performance and safety. -
Page 9: Use For The Intended Purpose
The encoder is in compliance with the relevant standards listed in the Declaration of Conformity for safety-relevant applications. Observe the notes in Chapter Securing functional safety (Page 11). Siemens AG does not accept any liability for injury and damage that result from the non-observance of these operating instructions. - Page 10 General information and safety notes 1.3 Use for the intended purpose The geared motor is only safe when used together with a suitable encoder evaluation and motor protection evaluation. The geared motor is certified for use in ambient temperatures ranging from -20 °C up to +40 °C, and an installation altitude up to 1 000 m above sea level.
-
Page 11: Securing Functional Safety
Securing functional safety General information The functional safety complies with the relevant standards listed in the Declaration of Conformity for safety-relevant applications. WARNING Non-compliance with warning information The functional safety can be disabled if the warning information and notes are not observed. - Page 12 If you optimize the controller parameters, e.g. using the appropriate current setpoint filtering, then you can rule out resonance effects such as these. For the geared motor with the encoder, Siemens AG assumes responsibility that the directives of functional safety are complied with. The safety-relevant connection elements are sealed before delivery.
- Page 13 The responsibility and liability regarding the functional safety and its associated traceability is completely transferred over to the operating company: ● If the operating company damages the seal that was applied by Siemens AG. ● If the operating company carries out work in the area around the seal.
-
Page 14: Unpacking
Securing functional safety 2.2 Unpacking Unpacking NOTICE Transport damage impairs the correct function of the geared motor Never commission faulty or defective geared motors. Check the geared motor for completeness and for damage. Report any missing parts or damage immediately. Keep the connector protection cap of the encoder on the connector until you connect the encoder to a suitable encoder evaluation unit. -
Page 15: Electrical Installation Of The Encoder
Securing functional safety 2.3 Electrical installation of the encoder Electrical installation of the encoder WARNING Inadequately qualified personnel If the encoder is electrically installed by inadequately qualified personnel then the functional safety can be disabled. Only qualified personnel are authorized to carry out the work. These persons must be knowledgeable about: •... - Page 16 Securing functional safety 2.3 Electrical installation of the encoder Connection assignment incremental encoder IN 8.5834 Diagram showing the signals for clockwise shaft rotation when viewing the clamping ring and/or the motor drive end. Connector viewed from the Signal outside Power supply Incremental signals Connection Sensor U...
-
Page 17: Commissioning The Encoder
Securing functional safety 2.4 Commissioning the encoder Commissioning the encoder WARNING Inadequately qualified personnel If the encoder is electrically installed by inadequately qualified personnel then the functional safety can be disabled. Only qualified personnel are authorized to carry out the work. These persons must be knowledgeable about: •... - Page 18 Securing functional safety 2.4 Commissioning the encoder FDU............. Factory serial number, see rating plate ③ The designated product is designed for installation in a machine. Commissioning is prohibited until it has been established that the end product conforms with Directive 2006/42/EC. Measure Is the maximum motor speed less than 3000 rpm.
-
Page 19: Technical Specifications
Description of the place holder for technical data Matrix code Applicable standard Factory serial number FDU = Siemens AG, Bahnhofstr. 40, 72072 Tübingen, Germany CE marking or other marking, if required Article number Type designation with marking of the functionally safe encoder... - Page 20 Securing functional safety 2.5 Technical specifications Frequency 1 Rated frequency f [Hz] Gearbox output speed n [rpm] Geared motor output torque T [Nm] Service factor f Frequency 2 Rated frequency f [Hz] Gearbox output speed n [rpm] Geared motor output torque T [Nm] Service factor f Motor data...
-
Page 21: Type Designation
Securing functional safety 2.5 Technical specifications 2.5.2 Type designation Example of a type designation of a motor equipped with a functionally safe encoder: LE90SG4E-L32/14N-IN SI04. The type designation is stamped on the rating plate in the area ⑥ . You can find the type designation code for the SIMOGEAR gearbox in the operating instructions BA 2030. -
Page 22: Technical Specifications Of The Brake
Securing functional safety 2.5 Technical specifications 2.5.3 Technical specifications of the brake Brake type Rated braking Working capacity Nominal air gap Maximum torque T air gap S Friction work until at 100 rpm the air gap is read- justed W [Nm] [MJ] [mm]... - Page 23 Securing functional safety 2.5 Technical specifications Brake type Rated braking Working capacity Nominal air gap Maximum torque T air gap S Friction work until at 100 rpm the air gap is read- justed W [Nm] [MJ] [mm] [mm] L150 (18E) L260 (20E) L400 (25E) BA 2730...
- Page 24 Securing functional safety 2.5 Technical specifications BA 2730 Operating Instructions, 08/2015, A5E36448105...
-
Page 25: Ec Declaration Of Conformity
EC Declaration of Conformity Document No. MD50.1 06.15 Manufacturer: Siemens AG Address: Bahnhofstraße 40, 72072 Tübingen, Germany Product designation: Encoder of the Kübler Sendix SIL 5834 FS, Sendix SIL 5883 FS series Installed in: Low-voltage motors, types • LA frame size 71 •... - Page 26 EC Declaration of Conformity The designated product is designed for installation in a machine. Commissioning is prohibited until it has been established that the end product conforms with Directive 2006/42/EC. First time that the CE marking was applied: 2015. Tübingen, June 25, 2015 Thomas Raster Lothar Hirschberger Head of Research &...