Advertisement
Table of Contents
- 1 Icon
- 2 Table of Contents
- 3 Introduction
- 4 Features
- 5 Precautions
- 6 About this Manual
- 7 Front Panel Description
- 8 Rear Panel Description
- 9 Balance Barrier Strip Input Connections
- 10 Barrier Strip Output Connections
- 11 Audio Transformer Outputs
- 12 Parallel Mono Configuration
- 13 Specifications
- 14 Block Diagram
- Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Phonic ICON 300
Summary of Contents for Phonic ICON 300
- Page 1 ICON 300 ICON 700 Contractor Power Amplifier ICON 700 English...
-
Page 2: Icon
IMPORTANT SAFETY INSTRUCTIONS The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable. -
Page 3: Table Of Contents
REAR PANEL DESCRIPTION…………………………………………….…………......6 BALANCE BARRIER STRIP INPUT CONNECTIONS……………………….………..…....7 BARRIER STRIP OUTPUT CONNECTIONS……………………………………….…..………..7 AUDIO TRANSFORMER OUTPUTS…………………………………………….……….….....8 PARALLEL MONO CONFIGURATION…………………………………………….……….…..9 SPECIFICATIONS..…………………………………………….…………........10 BLOCK DIAGRAM…………………………………………….………….........11 Phonic reserves the right to improve or alter any information supplied within this document without prior notice. V1.1 10/10, 2005... -
Page 4: Introduction
Congratulations on your purchase of the Phonic When first powering up the amp, keep the Icon 300 or 700 power amplifier. The Icon Series is amplifier gain controls all the off, in order to a line of professional power amplifiers specifically block potentially damaging or annoying sounds designed for contracting application. -
Page 5: Front Panel Description
LED will light for a few 4.Signal “Status” LED Indicator seconds, and then go out, indicating that Each channel of the Icon 300/700 features a signal the relay has closed. LED to show that there is an audio signal at the input to the channel. -
Page 6: Rear Panel Description
These are barrier strips to connect distributed line (25V, 70V, 100V, 140V and 200V). Spade lugs and bare wires should both be screwed down tight to exclude oxygen, and care should be taken to avoid loose strands of wire that may cause short circuits. ICON 300/700... -
Page 7: Balance Barrier Strip Input Connections
Tighten screw terminals. unbalanced input. Direct low impedance: Input sensitivities - Audio signals of these levels Output connection for Icon 300/700, will produce full rated output power at 8 ohms. bridge mono mode ICON 300 - 1.02Volts (+2.4dBu) ICON 700 - 1.02Volts (+2.4dBu) -
Page 8: Audio Transformer Outputs
240W or less. 140 volt line output connection, bridge mono mode 25 volt line output connection 50 volt line output connection 200 volt line output connection, bridge mono mode 100 volt line output connection ICON 300/700... -
Page 9: Parallel Mono Configuration
If your application calls for connection of an 8 ohm speaker and a distributed line to the same amplifier channel, the Icon 300 and Icon 700 are among the very few amplifiers that can do that. However, since most of the audio power is drawn by the direct-connected speaker, you must derate the distributed line;... -
Page 10: Specifications
Specifications ICON 300 ICON 700 Direct Power Out Max.average power at 45Hz-20kHz With 0.1% THD 8 ohm 120W×2 240W×2 4 ohm 200W×2 400W×2 2 ohm,1kHz,1%THD 300W×2 550W×2 Bridged mono 8 ohm,1kHz,1%THD 420W 850W Bridged mono 4 ohm,1kHz,1%THD 540W 1100W Isolated Constant Voitage Out... -
Page 11: Block Diagram
BLOCK DIAGRAM ICON 300 BLOCK DIAGRAM ICON 300/700... - Page 12 ICON 700 BLOCK DIAGRAM ICON 300/700...
- Page 13 Phonic, at its option, shall repair or replace the defective unit covered by this warranty. Please retain the dated sales receipt as evidence of the date of purchase.
Need help?
Do you have a question about the ICON 300 and is the answer not in the manual?
Questions and answers
what is connection for speaker