Download Print this page
Reznor LDAP Instructions
Reznor LDAP Instructions

Reznor LDAP Instructions

Gas conversion kit

Advertisement

Quick Links

General and
Warnings
FOR YOUR SAFETY
— WHAT TO DO IF
YOU SMELL GAS
Do not try to light
any appliance.
Do not touch any
electrical switch;
do not use any
phone in your
building.
Leave the building
immediately.
Immediately call
your gas supplier
from a phone
remote from the
building. Follow
the gas supplier's
instructions.
If you cannot
reach your gas
supplier, call the
fire department.
The gas burner in this gas-fired equipment is designed to provide safe, complete combustion.
However, if the installation does not permit the burner to receive the proper supply of combustion
air, complete combustion may not occur. The result is incomplete combustion which produces
carbon monoxide, a poisonous gas that can cause death.
Safe operation of indirect-fired gas burning equipment requires a properly operating vent system
which vents all flue products to the outside atmosphere. FAILURE TO PROVIDE PROPER VENTING
WILL RESULT IN A HEALTH HAZARD WHICH COULD CAUSE SERIOUS PERSONAL INJURY OR
DEATH.
For all heater installations, always comply with the combustion air requirements in the installation
codes and instructions. Model LDAP units installed in a confined space must be supplied with
air for combustion as required by Code and in the heater installation manual. Combustion air at
the burner should be regulated only by manufacturer-provided equipment. NEVER RESTRICT OR
OTHERWISE ALTER THE SUPPLY OF COMBUSTION AIR TO ANY HEATER. MAINTAIN THE VENT
SYSTEM IN STRUCTURALLY SOUND AND PROPER OPERATING CONDITION.
All gas conversion must be done by a qualified service person in accordance with
these instructions and in compliance with all codes and requirements. In Canada,
gas conversion shall be carried out in accordance with the requirements of the
Provincial Authorities having jurisdiction and in accordance with the requirements
of CSA-B149.1 and .2 installation code.
Improper installation, adjustment, alteration, service, or
maintenance can cause property damage, injury, or death.
Read the installation, operation, and maintenance instructions
thoroughly before installing or servicing this equipment.
FOR YOUR SAFETY : The use and storage of gasoline or
other flammable vapors and liquids in open containers in
the vicinity of this appliance is hazardous.
The conversion kit is to be selected and installed by a qualified
service person in accordance with these instructions and in
compliance with all codes and requirements of authorities
having jurisdiction. Failure to follow instructions could result
in death, serious injury and/or property damage. The qualified
agency performing this work assumes responsibility for this
conversion.
HAZARD INTENSITY LEVELS used in this manual.
1. DANGER: Failure to comply will result in severe personal injury or
death and/or property damage.
2. WARNING: Failure to comply could result in severe personal injury or
death and/or property damage.
3. CAUTION: Failure to comply could result in minor personal injury and/
or property damage.
DANGER
Gas Conversion Kit Instructions
WARNING
DANGER
Form CP-LDAP-GC, P/N 208881R6, page 1
Form CP-LDAP-GC (11-17)
Obsoletes CP-LDAP-GC (3-16)
Applies to: Model LDAP

Advertisement

loading
Need help?

Need help?

Do you have a question about the LDAP and is the answer not in the manual?

Questions and answers

Summary of Contents for Reznor LDAP

  • Page 1 For all heater installations, always comply with the combustion air requirements in the installation codes and instructions. Model LDAP units installed in a confined space must be supplied with air for combustion as required by Code and in the heater installation manual. Combustion air at the burner should be regulated only by manufacturer-provided equipment.
  • Page 2: Gas Conversion

    Application and The gas conversion kits in these instructions are for Model LDAP Size 400, 800, and 1200 heaters equipped with a single-stage or a Size 400 heater with a two-stage gas Kit Selection valve. See page 4 for a list of conversion kit components.
  • Page 3 If the heater will be operated above 6000 ft (1830M), a high altitude pressure switch (Option DJ20) must be installed. 7. Check for safe and proper operation of the heater by observing operation for at least one complete cycle. Form CP-LDAP-GC, P/N 208881R6, page 3...
  • Page 4 Be sure the surface is clean and dry and affix the tape to the (cont’d) heater. Close the access door. TABLE 2 - Inputs and Capacities by Altitude BTUH Inputs & Capacities by Altitude in the UNITED STATES for Model LDAP Normal Thermal Output Minimum...