Lennox Baltic BCK 020 Installation, Operating And Maintenance page 90

CONTROL INTERFACE DC50
Terminal display address configuration
The address of the terminal must be checked after having powered
the board.
- To access the configuration mode, press
them for at least 5 seconds.
- The screen shown in Fig28 will be displayed with the cursor
flashing in the top left hand corner.
- To change the address of the terminal display press the
once.
- Use the keys to select the desired value and confirm by
pressing .
- If the address was changed it will display the screen shown in
Fig29 .
D i s p l a y D i s p l a y D i s p l a y
D i s p l a y D i s p l a y
settings ....: nn settings ....: nn
settings ....: nn settings ....: nn settings ....: nn
I/O Board adress:XX I/O Board adress:XX I/O Board adress:XX
I/O Board adress:XX I/O Board adress:XX
D i s p l a y D i s p l a y D i s p l a y D i s p l a y D i s p l a y
changed changed changed changed changed
Assigning Terminal displays to control boards.
- Access the configuration mode by pressing
seconds.
NOTE : To access the board address menu you must go directly to
the bottom of the first screen (shown in Fig30 ) without changing
the terminal address as explained above.
- Press the key until the cursor moves to the field "I/O Board
address :XX". Fig 30
- Use the key to select the correct Climatic board.(N° of Unit)
- Pressing again will display the screen shown in Fig 31 .
- Pressing again will display the screen shown in Fig 32 .
- The field "P:XX " shows the address of the selected board. In the
example the value "12" has been selected.
- The filed under the "Adr" column represents the addresses of
the terminal displays associated with the board that has the address
"12", while the column under "Priv/Shared " indicate the type of
terminal selected.
Ph: Private
Sh :Shared
Sp : Shared Printer (N/A)
- To exit the configuration procedure and save the data, select the
filed "OK?NO", choose "Yes" using the
pressing .
If the terminal remains inactive (no button is pressed) for 30 se-
conds, the configuration procedure is aborted automatically.
together and old
a d r e s s a d r e s s a d r e s s
a d r e s s a d r e s s
Fig. 28
a d r e s s a d r e s s a d r e s s a d r e s s a d r e s s
Fig. 29
for at least 5
keys and confirm by
D i s p l a y D i s p l a y
D i s p l a y D i s p l a y D i s p l a y
settings ....: 17 settings ....: 17 settings ....: 17
settings ....: 17 settings ....: 17
I/O Board adress:XX I/O Board adress:XX I/O Board adress:XX
I/O Board adress:XX I/O Board adress:XX
key
Terminal Config Terminal Config Terminal Config Terminal Config Terminal Config
Press ENTER Press ENTER
Press ENTER Press ENTER Press ENTER
To continue To continue
To continue To continue To continue
P12:Adr Priv/ P12:Adr Priv/ P12:Adr Priv/ P12:Adr Priv/ P12:Adr Priv/
Shared Shared Shared Shared Shared
Trm1 17 pr Trm1 17 pr Trm1 17 pr Trm1 17 pr Trm1 17 pr
Trm2 32 sh Trm2 32 sh Trm2 32 sh Trm2 32 sh Trm2 32 sh
Trm3 None --OK? NO Trm3 None --OK? NO Trm3 None --OK? NO Trm3 None --OK? NO Trm3 None --OK? NO
Keys Time zone
settings
24.2°C ON 24.2°C ON 24.2°C ON
24.2°C ON 24.2°C ON
Set time
Out:40.0°C Z:A Out:40.0°C Z:A
Out:40.0°C Z:A Out:40.0°C Z:A Out:40.0°C Z:A
Back to main
Screen or
Cancel
"Override"
IOM / ROOFTOP BALTIC Series - 0704-E Page 89
a d r e s s a d r e s s
a d r e s s a d r e s s a d r e s s
Increase a
value or go to
FA:20% FA:20% FA:20% FA:20% FA:20%
DynFan:Auto DynFan:Auto DynFan:Auto
DynFan:Auto DynFan:Auto
Cool Cool Cool Cool Cool
Decrease a
value or go to
"Override
Fig. 30
Fig. 31
Fig. 32
"Override
menu"
Change
field or
validate
menu"