Related Manuals for Mhouse WG20
Summary of Contents for Mhouse WG20
- Page 1 MhouseKit WG20 For the automation of swing gates. Installation instructions and warnings...
-
Page 2: Table Of Contents
In any case, the manufacturer email: info@mhouse.biz guarantees their functionality and fitness for the intended purposes. http: www.mhouse.biz. WG20 is produced by NICE S.p.a. (TV) I, MHOUSE S.r.l. is an affiliate of the Nice S.p.a group. Contents 1 Warnings... -
Page 3: Warnings
1 Warnings • If this is the first time that you install a WG20 gate automation system • The WG20 automation system cannot be considered as a suit- we recommend that you dedicate some of your time to reading this man- able intrusion protection system. -
Page 4: Product Description
2.2 Description of the automation The following example of a typical WG20 application will serve to clarify a few terms and aspects of a gate automation system: Figure 1 A) CL20 control unit F) Pair of opening stops (not included);... -
Page 5: Description Of Devices
2.3 Description of Devices WG20 consists of the devices shown in figure 2; make immediately sure that they correspond to the contents of the package and verify the integrity of the devices. Note: to adapt WG20 to local regulations, the contents of the package may vary;... -
Page 6: Cl20 Control Unit
4 types of command to a single automation unit, or to control up to 4 different automation units. The transmission of the command is confirmed by the LED [A]; an eyelet [B] allows them to be hung on a keyring. Figure 9 6 WG20 Instructions... -
Page 7: Installation
1 "WARNINGS". 3.1 Preliminary checks WG20 must not be used to power a gate that is not efficient and • Using the leaf opening angle as a guideline, check that the safe. It cannot solve defects resulting from incorrect installation values in Table 6 can be met. -
Page 8: Operating Limits
3.1.3 List of Cables The cables required for the installation of WG20 may vary depending on the type and quantity of devices to be installed; figure 14 shows the cables needed for a typical installation; no cable is supplied with WG20. -
Page 9: Preparing The Electrical System
3.2.1 Connection to the Electrical Mains Although the connection of WG20 to the electrical mains is beyond the • The electric line must be grounded and protected against short scope of this manual, we wish to remind you that: circuits;... - Page 10 Figure 24 16 Firmly tighten the nut and then loosen it by about half a turn in order Figure 27 to allow the gearmotor to rotate on the support. 10 WG20 Instructions...
-
Page 11: Photocells
[D] should match the point where the cables come out of the wall; mark the drilling points using the bottom as reference. 6 Drill the holes in the wall using a hammer drill with a 5 mm bit and insert the 5 mm screw anchors. Figure 34 WG20 Instructions 11... -
Page 12: Ks1 Key-Operated Selector Switch
Figure 40 6 Drill the holes in the wall using a hammer drill with a 6 mm bit and insert the 6 mm screw anchors 12 WG20 Instructions... -
Page 13: Cl20 Control Unit
47. 4 Drill a hole through the bottom of the control unit and use suitable unions to fasten the conduits for the electric cables. Figure 48 WG20 Instructions 13... - Page 14 3 cm above the final position, then press it down until it snaps into place. When you have completed the connections, use clamps to secure the cables to the appropriate fasteners [C]. Figure 51 Figure 50 14 WG20 Instructions...
-
Page 15: Power Supply Connection
5.5 "Troubleshooting". The connected devices recognition stage can be repeated again at any Figure 56 time, even after the installation (for example, if an additional photocell is installed); just repeat the procedure starting from step 1. WG20 Instructions 15... -
Page 16: Recognition Of Gate Leaves' Opening And Closing Angles16
To switch from one speed to the other press the P2 button [B] momentarily; the corresponding P2 LED [A] will light up or go off; if the LED is off the speed is "slow", if the LED is on the speed is "fast". Figure 59 16 WG20 Instructions... -
Page 17: Selecting The Type Of Operating Cycle
14), analysis of hazards and solutions adopted, manufacturer's declaration of conformity of all the devices installed. For WG20 use 5 Prepare the maintenance schedule and deliver it to the owner of the Annexe 1 "EC Declaration of Conformity of the WG20 components". -
Page 18: Maintenance
If other devices are present, follow the directions provided in the The devices used for the WG20 automation system do not require any corresponding maintenance schedule. special maintenance. However, periodically make sure (at least once every six months) that all the devices are perfectly efficient. -
Page 19: Additional Information
5 Additional information The following chapters describe different ways of customizing WG20 to make it suitable for specific application requirements. 5.1 Advanced Adjustments 5.1.1 Adjusting the Parameters with the Radio Transmitter The radio transmitter can be used to adjust certain control unit operation 2) Pedestrian gate: pedestrian gate opening mode. -
Page 20: Checking The Adjustments With The Radio Transmitter
T1 and T2 for 5s and then button T1, the pause time is set at 40s. corresponding value in Table 8. 5.2 Optional Accessories In addition to the devices featured in WG20, other ones are available as PT50: Pair of 500 mm posts with one photocell optional accessories designed to enhance the automation system. -
Page 21: Recognition Of Other Devices
Figure 63 5.3.4 Addition of Optional Photocells Additional photocells can be installed at any time on top of those supplied with WG20. In an automation system for 2-leaf gates these can be arranged as shown in Figure 64. Figure 64... -
Page 22: Memorization Of Radio Transmitters
Tasto T4 "OPEN" command supplied with WG20 are memorized in Mode 1). It is obvious that in Mode 1 a radio transmitter can be used to command a single Each transmitter is, of course, a separate unit, and while some are automation, i.e.:... -
Page 23: Deleting A Radio Transmitter
10-30Vac); if there is voltage, the problem is flashing light does not work due to the lamp; in this case replace the lamp with one having the same characteristics. Figure 68 WG20 Instructions 23... -
Page 24: Diagnostics And Signals
Cutting in of the "motor force" limiting device identify the cause 3 flashes 4 flash During the movement the STOP input was activated; identify 1 second's pause Cutting in of the STOP input the cause 4 flashes 24 WG20 Instructions... -
Page 25: Control Unit
Carry out the recognition stage (see paragraph "3.5.2 recognition of Leaves' 1 flash every second memorized Opening and Closing Angles") Recognitionof opening angles in 2 flashes every second It indicates that the recognition of the opening angles is under way progress Figure 70 WG20 Instructions 25... -
Page 26: Technical Characteristics
6 Technical characteristics WG20 is produced by NICE S.p.a. (TV) I, MHOUSE S.r.l. is an affiliate of the Nice S.p.a group. Nice S.p.a., in order to improve its products, reserves the right to modify their technical characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes. - Page 27 Security lock Key with 450 different key numbers The device can only be connected to the "OPEN" and "STOP" terminals on the MHOUSE gate automation Power supply/contacts control units, to which it sends the control signals and by which it is energized for night illumination Operating ambient temperature -20 ÷...
-
Page 28: Annexes
The following annexes are designed to help you prepare the technical documentation. 7.1 Annexe 1: CE Declaration of Conformity of WG20 Components CE Declaration of Conformity of WG20 components; this statement must be attached to the technical documentation. 7.2 Annexe 2: CE Declaration of Conformity of Power Operated Gate CE Declaration of Conformity to be filled in and delivered to the owner of the power operated gate. - Page 29 Declaration of conformity EC Declaration of Conformity with Directives 98/37/EC, 73/23/EEC, 89/336/EEC and 1999/5/EC WG20 is produced by NICE S.p.a. (TV) I; MHOUSE S.r.l. is an affiliate of the Nice S.p.a. group. Number: 214/WG20/GB Date: 02/02/2005 Revision: 1 The undersigned Lauro Buoro, in his capacity as Managing Director, declares under his sole responsibility that the following product: Manufacturer's name: NICE s.p.a.
-
Page 31: Annexe 2: Ce Declaration Of Conformity Of Power Operated Gate
Declaration of conformity According to Directive 98/37/EC, ANNEXE II, part A (CE declaration of conformity for machines) The undersigned / Company (name or business name of person who has put the power operated gate into service ) (address) Declares under his/her sole responsibility that: The automation : power operated gate with swing leaves Serial number... -
Page 33: Annexe 3: Operating Guide
The selector switch has two positions, with automatic return to the centre. Figure 72 ACTION FUNCTION Rotated to the right: "OPEN" Rotated to the left: "STOP" It stops the movement of the gate (*) This item must be drafted by the person who has programmed the system:. WG20 Instructions 33... -
Page 34: Maintenance Operations To Be Performed By The User
2 Insert the key in the pin. The gearmotor is equipped with a mechanical system which allows the gate to be opened and closed manually (i.e. as if WG20 were not present). The manual operation must be resorted to in case o power failures or system malfunctions. - Page 36 Mhouse Via Pezza Alta, 13 - Z.I. Rustignè 31046 Oderzo TV Italia Tel. +39 0422 20 21 09 Fax +39 0422 85 25 82 info@mhouse.biz www.mhouse.biz...
Need help?
Do you have a question about the WG20 and is the answer not in the manual?
Questions and answers