Section 1 Wiring; 12Vdc Supply Wire; Wire From Control Box To Awning; Wire Inside Hardware Channel (Weatherpro Only) - Dometic Weather Pro Service Manual

SECTION 1 WIRING

1.1

12VDC Supply Wire

1.1.1 The 12VDC supply wire must be run from
the 12VDC supply source to the Control
Box. It is recommended that these wires
be RED+ and Black– 12 gauge wires. This
needs to be on a separate 15 amp circuit.
See FIG. 1.1A & 1.1B.
1.1.2 To ensure proper operation, the control
box must have a minimum of 12.5 VDC at
the control box during operation. Check
voltage output on the Red and Black wire
at the control box. If voltage is below 12.5,
check voltage at supply, If OK it may be
necessary to increase the wire size going
to the control box. See FIG. 1.1A.
FIG. 1.1A
12VDC
Power Supply
15 AMP
Breaker
Red +
Open
Close
1.1.3 If the control is the part number 3307930
& 3309114 the voltage can be checked
on the pins (1) and (2) of the 15 pin MATE-
®
N-LOK
DC-. See FIG. 1.1B
1.2 Wire From Control Box to Awning. Arm As-
sembly (WeatherPro) and Awning Motor (Oa-
sis Elite)
A Red and Black Wire (WeatherPro) Red/White
and Blue or Black/White wire (Oasis Elite) of
adequate size must be run between the control
box and the awning. To avoid voltage drop fol-
low the chart below to determining the proper
size wire to be used.
Wire Length
10' & Under
11' to 30'
Over 30'
FIG. 1.2
Red
Black
Pig Tail to
Control Box
End
Black
Red
+12.5
VDC
Black-
*FUSE LOCATED INSIDE
plug. Pin (1) is DC+ and pin (2) is
Wire Size
14 Gauge
12 Gauge
10 Gauge
WeatherPro
Main Arm
Right Side
Pig Tail
for Motor
Red
Black or Blue
Black
Red/White
Blue or Blk/Wh
Oasis Elite
Motor
Open
*FUSE LOCATED INSIDE
Close
3307930 & 3309114 Control Box Kit Using
Universal MATE-N-LOK
WeatherPro
Awning
Main Arm
Right Side
FIG. 1.1B
Cable to Wind Sensor Cable to Wind Sensor
18-20 Gauge 18-20 Gauge
(18 Foot Maximum) (18 Foot Maximum)
Location
Pin 1 12+VDC
Pin 2 12- VDC
Pin 3 Ignition Isolator
Pin 4 Oasis Elite Remote Switch
Pin 5 WeatherPro Remote Switch
Pin 6 Blank
Pin 7 Oasis Elite Motor (-12VDC)
Pin 8 WeatherPro Motor (-12VDC)
Pin 9 Oasis Elite Remote Switch
Pin 10 WeatherPro Remote Switch
Pin 11 Blank
Pin 12 Oasis Elite Motor (+12VDC)
Pin 13 WeatherPro Motor (+12VDC) Red
Pin 14 Oasis Elite Remote Switch
Pin 15 WeatherPro Remote Switch

1.3 Wire Inside Hardware Channel (WeatherPro Only)

FIG. 1.3
Red
4
R Soft Shell Connector
Yellow (10)
Yellow/White (9)
WeatherPro
Brown (15)
Remote Switch
Brown/White (14)
Green (5) Green/White (4)
Ignition
Pink (3)
Isolator
15
13 14
10 12
11
7 8 9
4 5 6
Red (13)
Blue or BlK/Wh (7)
1
2
1 2 3
Black (8)
Red/White (12)
AMP 2-Pin
Connector
R
AMP UNIVERSAL MATE-N-LOK
Soft Shell Connector
15
13 14
10 11 12
7 8 9
4 5 6
1 2 3
Wind Sensor Switch
ENABLE (ON)
DISABLE (OFF)
Open
*FUSE LOCATED INSIDE
Close
Black 1
Red 2
Green 3
Yellow 4
Pin Functions Wire Color
Red
Black
Pink
Green/White
Green
Blue or Blk/Wh See chart in 1.2
Black
Yellow/White
Yellow
Red/White
Brown/White
Brown
To make the connection between the wire run in
1.2 and the awning motor there is a cable run in
the hardware from the bottom to the top. Check
this wire for pinches or breaks. If wire is defec-
tive replace with new harness. See FIG. 1.3.
Cable
Oasis
Elite
Remote
Switch
2
1
Oasis
Elite
FRTA
Auto Resettable Fuse
Used On Some Models
Cable Between MATE-N-LOK
4 Pin Connectors
Customer Supplied
18-20 Gauge
(18 Foot Maximum)
Wire Size
12 Gauge
12 Gauge
16 Gauge
16 Gauge
16 Gauge
See chart in 1.2
16 Gauge
16 Gauge
See chart in 1.2
See chart in 1.2
16 Gauge
16 Gauge
Cable
Right Arm
Assembly