Advertisement

Signal Booster
Model: A7V-
SR65703001
Manual
If you have any questions or concerns when
installing or operating your cell phone booster,
please email us:
Support@SolidRF.ca
Please provide the invoice of your product in
your email. Or visit www.SolidRF.ca for more
information.
Systems tested and certified against FCC
standard, Equipment Class: Part 20 Wideband
Consumer Booster (CMRS)
Systems tested and certified against IC standard,
Type of Equipment: Amplifier, RSS-131
Manufactured and Warranted by
SolidRF Technology Inc. Canada
www.SolidRF.ca
Product Diagram
Package Contents
Features
Test Installation
Installation – Step By Step
Technical Specification
Self Oscillation
Quick Troubleshooting
Find Strongest Signal

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A7V-SR65703001 and is the answer not in the manual?

Questions and answers

Summary of Contents for SolidRF A7V-SR65703001

  • Page 1 Features Support@SolidRF.ca Test Installation Please provide the invoice of your product in your email. Or visit www.SolidRF.ca for more Installation – Step By Step information. Technical Specification Systems tested and certified against FCC standard, Equipment Class: Part 20 Wideband...
  • Page 2: Package Contents

    Package Contents MAIN UNIT • Main Unit • Remote Unit Antenna 1 Fiber Connector Antenna 2 Remote UNIT RF Output1 RF Output2 RF Output3 RF Output4 Fiber Connector Features • Greatly reduces dropped calls, extends signal range, and increases data rates •...
  • Page 3: Test Installation

    Find a cell tower nearby! There are a bunch of resource online, here are some third party websites and app recommended. SolidRF does NOT guarantee the accuracy or completeness on Third Party content For Canada website: www.cellmapper.net...
  • Page 4 Step3: Introduce cables into room Attention: Don’t excessive bending of the cable, otherwise it will be damaged and loss functions. Step4: Setup Main Unit 1. Connect antenna cable to “Antenna 1” and “Antenna 2” connecter, make sure pin of the cable head smooth import connecter’s socket, and then screw...
  • Page 5 Step5: Power on and evaluate effects 1. Power on booster; 2. Observe the flashing status of “ALARM” lights; 3. If the lights lit 1 second and then goes out, that means all the test installation is correct; 4. Now check your cell phone to see how about the signal strength improved;...
  • Page 6: Technical Specification

    SolidRF, any other products non-approved by • Wrong condition: If any of the lights flashing in SolidRF or self-made power cable may damage the green light, than means the isolation between booster. the outside antenna and inside antenna is lower than it should be, and self oscillate occurred.
  • Page 7 ATTENTION: Self Oscillation We strongly recommend it must achieve the Minimum Required Separation Distance for the installation. The improper installation could result in possible Self Oscillation. Minimum Required Separation Distance (MRSD):6 meters (20 ft ) distance and 4 meters ( 13 ft ) vertical height distance.
  • Page 8: Quick Troubleshooting

    20 ℃ to +50 ℃. Too high or low temperatures beyond this range will cause the booster to lower output power to avoid damage. If you can not fix the problem, please contact the technical support or the reseller. SolidRF Technical Support: Support@SolidRF.ca Find Strongest Signal Use Cell Phone Only: •...
  • Page 9 (1) Usage of unauthorized antennas, cables, and/or coupling devices may result in poor effect and, in severe cases, equipment damage. (2) a complete list of authorized antennas, cables, and/or coupling devices:...
  • Page 10 (5) Contact information for providers: Shen hen SolidRF Communications Co., Ltd Add: No. 8, Shop D, Block C, Shan Shui u, Long Wei Rd, Shenzhen, 518049 China...

Table of Contents