Subscribe to Our Youtube Channel
Related Manuals for Leroy-Somer VARMECA 30
Summary of Contents for Leroy-Somer VARMECA 30
- Page 1 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor Installation and maintenance...
- Page 2 VaRmeca 30 motor is fitted with safety devices which, in the event of a fault, control stopping and thus stop the motor. the motor itself can become jammed for mechanical reasons. Voltage fluctuations, and in particular power cuts, may also cause the motor to stop.
- Page 3 VARMECA 30, since electrical risks may lead to specifications in the manual supplied with the product. material or physical damage as well as constituting a fire VaRmeca 30 motors must be protected against excessive hazard.
- Page 4 LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor NOTES...
-
Page 5: Table Of Contents
LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor CONTENTS 1 - GENERAL INFORMATION ..........................6 1.1 - General operating principle ..........................6 1.2 - Product name..............................6 1.3 - characteristics ..............................7 1.4 - environmental characteristics ........................... -
Page 6: General Information
• This manual describes the characteristics and installation of the VARMECA 31ML, 31M, 31TL, 31T, 32M, 32TL, 32T, 33TL, 33T, 34TL, 34T. • The VARMECA 30 is designed to operate in an industrial environment. When used with an external EMC filter, the VARMECA 30 complies with standards for residential environment. -
Page 7: Characteristics
LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor OPERATING EXTENSIONS Designation Description B 31/32 or B 33/34 Integrated speed control knob Bma 31/32 or Bma 33/34 speed control knob and integrated run-stop control knob... - Page 8 - short-circuit on 0-10 V/24 V inputs or outputs - By switching off the VaRmeca 30 or by opening/closing the connection between the 24V and Drive reset ena (Vma 31/32) terminals or sDI 1 and sDI 2 (Vma 33/34) terminals...
-
Page 9: Environmental Characteristics
LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor 1.4 - Environmental characteristics Characteristics Level Index of protection IP 65 (if motor IP 65) storage temperature - 40 °c to + 70 °c conforming to standard Iec 68-2-1* transport temperature - 40 °c to + 70 °c... - Page 10 1.5.2 - Standards (Emission) the maximum emission level is set by the generic industrial (en 61000-6-4) and residential (en 61000-6-3) standards. VaRmeca 30 conforms to the following standards: en 61000-6-4 (en 50081-2), en 61000-6-3 (en 50081-1), en 61800-3 (ceI 61800-3).
- Page 11 VaRmeca 30 can be supplied with its filter integrated VaRmeca 30 by one of the following 2 methods: • Use of shielded twisted pair cable, with shielding connected and wired-up.
-
Page 12: Description Of Cables And Protection Devices
1.6 - Description of cables and protection devices • It is the responsibility of the user to connect and provide protection for the VARMECA 30 in accordance with the legislation and regulations in force in the country of use. This is particularly important as regards the size of cables, the type and rating of fuses, the earth or ground connection, powering down, acknowledging faults, insulation and protection against overcurrents. -
Page 13: Operating Ranges According To The Switching Frequency
InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor Three-phase power supply 208V - 10 % to 240V + 10 % Three-phase power supply 380V - 10 % to 480V + 10 %... -
Page 14: Weights And Dimensions
LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor 1.9 - Weights and dimensions Dimensions (mm) Type VMA rating Weight (kg) ls 71 31ml-31m - 31tl - 31t 31ml-31m - 31tl - 31t... -
Page 15: Installation
VaRmeca 30 motor is fitted to the machine like a standard and with the regulations in force in the country of use. -
Page 16: Control Terminal Blocks
InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor 3.2 - Control terminal blocks • Check that the terminal block has been removed from its fixed holder (unplugged) before making any connections, so as to avoid putting pressure on the card. - Page 17 LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor terminal terminal Designation Function Characteristics 33/34 31/32 characteristics analogue voltage (common mode) or uni-directional current Voltage input Full scale voltage 10 V ± 2%...
-
Page 18: Power Terminal Blocks
(protocols supported: PRoFIBUs DP, InteRBUs s, DeVIce and/or the rear of the VaRmeca 30 casing. net and can oPen). screw terminal block: Vma 33/34 Vma 31/32 3.4.4 - P2 connector (VMA 31/32 only) -
Page 19: Wiring Diagrams
LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor 3.5 - Wiring diagrams 3.5.1 - Standard configuration connection diagram VARMECA 31/32 0-10 V/4-20mA (1) speed reference ADI1 Mains supply (local options or external ref.) - Page 20 LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor 3.5.2 - Connection diagram with safety input • The safety input is a safety component which must be incorporated into the complete system dedicated 3.5.2.1 - Safety input...
- Page 21 LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor 3.5.2.2 - 3-phase AC power supply in accordance with safety standard EN954-1 - category 1 with use of safety input VARMECA 31/32...
-
Page 22: Power Supply And Control For Fcr Brake Motors
LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor 3.6 - Power supply and control for 3.7 - Example of supplying 2 motors FCR brake motors with or without brake in parallel with a single VARMECA 3.6.1 - Power supply for the built-in... -
Page 23: Wiring Diagrams For Esfr Vma
LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor 3.8 - Wiring diagrams for the ESFR VMA option 3.8.1 - Connection of the ESFR VMA 31/32 option L1 L2 L3 230/400V... - Page 24 LEROY-SOMER InstallatIon anD maIntenance 3776 en - 2013.06 / k VARMECA 30 Variable speed motor or geared motor Brake connection on + and - terminals F1 and F2 output for a 2nd brake Dedicated logic output connection Power supply on...
-
Page 25: Commissioning
31/32, BMAVAR 33/34 option moving parts are mechanically protected. • For the safety of personnel, the VARMECA 30 must not be once it has been switched on, the motor starts after the control switched on with the protective cover removed. -
Page 26: Faults-Diagnostics
5 - FAULTS - DIAGNOSTICS Information relating to the status of the VaRmeca 30 is provided by two indicator lamps located on the local control options (B 31/32 or B 33/34, Bma 31/32 or Bma 33/34, BmaVaR 31/32 or BmaVaR 33/34, cVI Vma 31/32 or cVI Vma 33/34 options), or by the internal leD in Vma 31/32. -
Page 27: Options
In addition to speed control, a forward button, a reverse button the speed is set using a knob with graduations from 15 to and a stop button make it possible to control the VaRmeca 30 100%. locally, once it has been switched on, as required. For a run •... -
Page 28: Ip 20 Braking Resistor (Rf100 - Rf200 - Rf600)
7.8 - Power supply and sequential brake control (ESFR VMA 33/34) the brake has a built-in power supply. the brake is controlled according to a sequence which can be adjusted using the VaRmeca parameters. see VaRmeca 30 parameter-setting manual. 7.9 - Fieldbus (VMA 33/34) RF 100 RF 200 the interface card is mounted inside the VaRmeca casing. -
Page 29: Parameter-Setting Console (Px Lcd)
XPress Key option is used to save a copy of all the settings (terminal block configuration, ramp, speed and PI VaRmeca 30 parameters so that they can be duplicated very settings, etc). simply in another drive. -
Page 30: Emc Filter For Vma33/34
(Flt Vma31-32m 110) is internally mounted up to because of the emc filter which can be integrated in the front of power rating 1.1 kW. the VaRmeca 30 casing. For the power 1.5kW, the filter is externally mounted, on the rear of the case.
Need help?
Do you have a question about the VARMECA 30 and is the answer not in the manual?
Questions and answers