Related Manuals for Epson S5U1C6S3N2E2
Summary of Contents for Epson S5U1C6S3N2E2
- Page 1 MF1161 - 02 CMOS 4 - BIT SINGLE CHIP MICROCOMPUTER S5U1C6S3N2E2 Manual (Evaluation Board for S1C60N09/6S3N2/62N33)
- Page 2 No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any...
- Page 3 The information of the product number change Starting April 1, 2001, the product number will be changed as listed below. To order from April 1, 2001 please use the new product number. For further information, please contact Epson sales representative.
-
Page 5: Table Of Contents
CONTENTS S5U1C6S3N2E2 Manual (Evaluation Board for S1C60N09/6S3N2/62N33) This manual describes how to operate the S5U1C6S3N2E2, a debugging tool for the S1C6S3N2, S1C62N33 and S1C60N09 4-bit single-chip microcomputers. Refer to the Technical Manual of each model for details of the S1C6S3N2, S1C62N33 and S1C60N09, and the "S5U1C62000A Manual"... -
Page 7: Introduction
S5U1C6S3N2E2 board.) In addition, the S5U1C6S3N2E2 can interface with the in-circuit emulator ICE (S5U1C62000H), and so perform a higher level of debugging. The set-up data for each option can be loaded from a PC. -
Page 8: Product Specifications
2 PRODUCT SPECIFICATIONS 2 PRODUCT SPECIFICATIONS The components specifications of the S5U1C6S3N2E2 are listed below. S5U1C6S3N2E2 203 mm (width) × 275 mm (depth) × 65 mm (height) (Including rubber feet) Dimensions: Weight: About 2 kg (main unit only) Color: Cygnus white Power supply: 5 V (±10%) DC, 3 A or more... -
Page 9: Names And Functions Of Parts
Install the EPROM containing the application program and execute the program. Interface with ICE The S5U1C6S3N2E2 can interface with the ICE so that a higher level debugging environment may be established. Setting hardware options by installing function option and segment option ROMs Hardware options, i.e., I/O ports and LCD segments, can be specified by writing option data for the... -
Page 10: Board (Under Top Cover)
(Refer to Section 6.2, "Differences from Actual IC".) • VSVD (can be used only when the S5U1C6S3N2E2 is set for the S1C6S3N2 or the S1C62N33) This is the control for varying the power supply voltage in simulation to check SVD (BLD) operation. - Page 11 ICE. • DONE/PG This LED lights when initial reset of this board has been completed after the S5U1C6S3N2E2 is turned • HVLD, SVDON*, OSCC*, AMPON*, CSDC, SWRUN, EVRUN* These LEDs indicate the values ("1" or "0") of the following resisters. LED lights when "1" is set in the resister, and it goes off when "0"...
-
Page 12: S5U1C6S3N2E2 I/O And Lcd Connectors
3 NAMES AND FUNCTIONS OF PARTS 3.3 S5U1C6S3N2E2 I/O and LCD Connectors S1C6S3N2 Table 3.3.1 I/O #0 connector pins Table 3.3.2 LCD #0 connector pins Signal name Signal name Signal name Signal name (+5 V) (+5 V) COM0 COM1 COM2... - Page 13 Cannot be connected Cannot be connected Cannot be connected Cannot be connected Cannot be connected Cannot be connected Cannot be connected Cannot be connected Note: Do not use pins that cannot be connected. EPSON S5U1C6S3N2E2 MANUAL (EVALUATION BOARD FOR S1C60N09/6S3N2/62N33)
-
Page 14: Cable Connection
Note: Turn the power of all equipment off before connecting or disconnecting cables. 4.1 Connection to ICE The S5U1C6S3N2E2 is connected to the ICE by connecting the two interface cables (F1 and F5). Use S5U1C6S3N2E2 connectors F1 and F5 with the projections facing outwards. Use ICE connectors F1 and F5 with the projections facing inwards (cable side). -
Page 15: Power Cable Connection
4 CABLE CONNECTION 4.2 Power Cable Connection When using the S5U1C6S3N2E2 on its own, it must be supplied with power (5 V DC, 3 A or more) from an external source through the power cable. When the S5U1C6S3N2E2 is connected to the ICE, the power is supplied by the ICE; therefore, the power cable is not necessary. -
Page 16: Operation Method Of S5U1C6S3N2E2
LCD connector supplied with the S5U1C6S3N2E2 to connect the S5U1C6S3N2E2 to the target system. (For the pin layout of each connector, refer to Section 3.3, "S5U1C6S3N2E2 I/O and LCD Connectors".) Note: There is some difference in specifications between the S5U1C6S3N2E2 and the actual CPU. Refer to Section 6.2, "Differences from Actual IC"... -
Page 17: Independent Use Of S5U1C6S3N2E2
(2) Keep on turning the POWER switch off. 5.3.1 Power on/off Power to the S5U1C6S3N2E2 is supplied by the ICE, and the power is switched on and off by pressing the POWER switch of the ICE. Keep the POWER switch of the S5U1C6S3N2E2 off. -
Page 18: Precautions
<Output port drive capability> The drive capability of each output port on the S5U1C6S3N2E2 is higher than that of the actual IC. Check the drive capability of each output terminal on the model by referring to its Technical Manual before designing the system and software. - Page 19 <Pull-down resistance> The K ports of the S5U1C6S3N2E2 have a 1 MΩ pull-down resistor and the P ports have a 200 kΩ pull-down resistor which are different from those of the actual IC. For the resistor value of the actual IC, refer to the Technical Manual for each model.
- Page 20 OSC3. The same applies when turning the OSC1 oscillation off after switching the clock from OSC3 to OSC1. The S5U1C6S3N2E2 may operate if this processing is performed at the same time. Be sure to use separate instructions according to the actual IC when creating the program. * •...
- Page 21 Central Phone: +852-2585-4600 Fax: +852-2827-4346 101 Virginia Street, Suite 290 Telex: 65542 EPSCO HX Crystal Lake, IL 60014, U.S.A. EPSON TAIWAN TECHNOLOGY & TRADING LTD. Phone: +1-815-455-7630 Fax: +1-815-455-7633 10F, No. 287, Nanking East Road, Sec. 3 Northeast Taipei 301 Edgewater Place, Suite 120...
- Page 22 S5U1C6S3N2E2 Manual (Evaluation Board for S1C60N09/6S3N2/62N33) ELECTRONIC DEVICES MARKETING DIVISION EPSON Electronic Devices Website http://www.epson.co.jp/device/ First issue December, 1998 Printed March, 2001 in Japan...