Table of Contents
Advertisement
Auto Mode will find an efficient and economical way to run automatically according to the relative
humidity and temperature.
Ideal Usage: Use this mode for maximum energy saving and for quiet operation.
Quick Dry mode: The unit will operate the heater in a high working status and fan at a high speed to
dehumidify a very damp room in the first couple of days. It is suggested to switch to "NORMAL DRY"
mode whilst the relative humidity goes down to save more energy.
Ideal usage: Use to dry clothes quickly over a short period of time or to dry a very damp room quickly.
Normal Dry mode: The machine works the heater in a low working status and fan at
"Medium" speed.
Ideal usage: Use to dry clothes over a longer period of time; this is more economical than "QUICK
DRY" mode.
Eco mode: The Heater is off and the fan will operate on a low speed to reduce the noise level, the
dehumidifier will sample the air for its humidity level and will dehumidifier again when relative humidity
rises.
Ideal usage: Use on a daily basis in your home to keep the humidity to a healthy level of approx.
55%RH. Bacteria and mould will not breed at this level.
•
Press the "TIMER" button to select the required time from 1 Hour to 8 Hours
•
The unit will automatically stop when the pre-set time has finished. You can change the selected time
if necessary. Press the "TIMER" button to change or stop the pre-set timer.
Note: After 4 hours of continuous use, the heater motor will automatically stop for 3 minutes to
ensure that the unit doesn't overheat. The Fan will continue to run during this period.
Note: After 12 hours of continuous use, the unit will automatically switch off and the LED lights will
flash, this is normal and is designed to prevent the unit from overheating. After a short time you can
restart the unit by unplugging from the socket and then plugging back in.
•
You can turn the unit off at any time by pressing the "ON/OFF" button
Note: After pressing the "ON/OFF" button to turn the unit off, the fan will continue running for 2
minutes to circulate the heat, DO NOT remove the plug until the fan has completely stopped.
•
Press the "OSCIL" button to select the angle of the air flow - 90° / 45° Lower / 45° Upper
•
Press the "ION" button to Start and Stop the Ioniser function, which recharges the negative ions to
purify the air.
Note: This function can only operate when the filter is installed
REMOVABLE PARTS
Install the Filter
•
Pull the handle up
•
Pull the filter upwards from the back
of the unit
•
Place the filter into the slots and push downwards
until it locks into position, you will hear a "click" sound.
How to empty the water tank
•
Underneath the water tank there is a handle.
Grip the handle and pull out the water tank completely.
•
Remove the lid from the water tank
•
Empty the water down a sink
•
Replace the lid and push the water tank
back into position.
7
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the IG9807 and is the answer not in the manual?
Questions and answers
How do I switch my humidifier on when the on off light is flashing and the timer lights for 1 hour and 2 hours are flashing?
If the on/off light and timer lights for 1 hour and 2 hours are flashing, the unit has likely stopped automatically after 12 hours of continuous use as a safety feature to prevent overheating. To turn the iGenix IG9807 dehumidifier back on, follow these steps:
1. Ensure the unit is plugged in securely.
2. Press the power button to restart the unit.
3. If the unit does not turn on, unplug it from the power source.
4. Wait a few minutes, then plug it back in.
5. Press the power button again to turn the unit on.
If the issue persists, check the troubleshooting guide for additional solutions.
This answer is automatically generated
the on/off light and 4hr lights are flashing and unit is beeping i have unplugged and tried again but to no avail any advice appreciated also is there some way of resetting the unit regards
If the ON/OFF light and 4-hour lights are flashing and the iGenix IG9807 unit is beeping, it indicates that the unit has been running continuously for several hours and has automatically switched off to prevent overheating. This is a normal safety feature.
To reset the unit:
1. Unplug it from the socket.
2. Wait for a short time.
3. Plug it back in and restart the unit.
This answer is automatically generated