1. Manuals
  2. Brands
  3. Zaxcom Manuals
  4. Receiver
  5. ERX2TCD
  6. User manual

Zaxcom ERX2TCD User Manual

Zaxnet audio &time code receiver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER MANUAL
Published December 2018
Firmware Version 2.11
ERX2TCD
ZaxNet Audio &Time Code Receiver
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ERX2TCD and is the answer not in the manual?

Questions and answers

Related Manuals for Zaxcom ERX2TCD

Summary of Contents for Zaxcom ERX2TCD

  • Page 1 USER MANUAL Published December 2018 Firmware Version 2.11 ERX2TCD ZaxNet Audio &Time Code Receiver...

  • Page 2: Table Of Contents

    NTERFACING THE WITH A OMAD FIRMWARE ..............................15 IFB 100 / 200 ....................15 PDATING FIRMWARE USING AN ....................16 PDATING FIRMWARE USING AN TRANSMITTER ERX SPECIFICATIONS ............................ 17 PRODUCT SUPPORT ............................. 18 ZAXCOM WARRANTY POLICY AND LIMITATIONS ................... 19...

  • Page 3: Knowing Your Erx

    Zaxcom ERX3TCD ERX Layout Knowing your ERX 1. OLED Screen Battery Compartment 2. INC Key 1/8” Locking Headphone Jack 3. Menu key Power Switch 4. DEC Key Signal / Power LED 5. Time Code key Volume Knob Page 3...

  • Page 4: Erx Control Keys

    The main screen of the ERX will display timecode, battery level and receive 01:02:03:04 audio level. If the ERX is receiving signal from a Zaxcom recorder the scene, take and S: (SCENE INFO) user-bits can be displayed by pressing and holding the INC or DEC key.

  • Page 5: Erx Receive Antennas

    Zaxcom ERX3TCD ERX Layout ERX Receive Antennas The ERX has four receive antennas located behind the faceplate as indicated below. Please note if placed in a pocket, ERX should be facing out. To ensure better performance don’t place anything in front of these areas that...

  • Page 6: Extended Menu

    Zaxcom ERX2TCD Extended Menu Extended Menu Accessing and navigating the extended menu Press and hold the MENU key while powering up the ERX or press the time code key 3 times from the home • screen. Pressing the MENU key will advance to the next menu item.

  • Page 7: Ifb Receive Frequency Set

    Zaxcom ERX3TCD Extended Menu IFB Receive Frequency Set FREQ: 2.403 RX SIGNAL: A01 B01 The IFB receive menu is where the ZaxNet receive frequency is set. To manually adjust the receive frequency press the INC or DEC keys to match the transmit frequency.

  • Page 8: Auto Scan Enable

    Zaxcom ERX3TCD Extended Menu Auto Scan Enable AUTO SCAN: When auto scan is enabled the ERX will automatically search for, and lock to, a valid ZaxNet transmit frequency. Therefore if the transmitters’ frequency is changed, the ERX will automatically search for the new frequency so the ERX doesn’t need to be manually set to the new frequency.

  • Page 9: Time Code Output Enable

    Zaxcom ERX3TCD Extended Menu Time Code Output Enable TIMECODE OUTPUT The ERX can output time code through either side of the headphone jack. When sending time code to the headphone jack, the time code will override the audio to that selected output. The ERX can be configured to send audio only, time code only or time code and audio simultaneously.

  • Page 10: Manual Time Code Set

    Zaxcom ERX3TCD Extended Menu Manual Time Code Set TC TIME ENTRY: >H 00 If an ERX is not receiving time code from a ZaxNet time code source the time code generator in the ERX can manually be set from this menu.

  • Page 11: Time Code Calibration Value

    Zaxcom ERX3TCD Extended Menu Time Code Calibration Value TC CALIBRATION: The time code calibration value menu will display the auto calibration time code offset. The time code calibration value represents the difference between the source and the time code generator in the ERX which is .062 milliseconds per hour of adjustment.

  • Page 12: Zaxnet Output Enable

    / disables the ERX to output the commands that are embedded within the time code output. If the ERX is not sending the time code to another Zaxcom device this should be set to OFF. Time Code Output Level Adjust TC OUTPUT LEVEL: 1.0 VOLTS...

  • Page 13: Alternative Ifb Frequency Set

    Zaxcom ERX3TCD Extended Menu Alternative IFB Frequency Set ALTERNATE IFB FREQ: 2.420 The alternative IFB frequency allows the ERX to receive audio from additional ZaxNet sources so a listener could toggle between multiple frequencies from different ZaxNet transmitters. The ERX can toggle up to 12 frequencies.

  • Page 14: Erx Quick Start Guide - Interfacing With Nomad

    Zaxcom ERX3TCD Interfacing with a Nomad ERX Quick Start Guide - Interfacing with Nomad Interfacing the ERX with a Nomad 1. In the main menu of Nomad select ZaxNet Setup 2. Scroll down and select Input Configure. Make sure that the input configure is set to 8 or higher. Press the back button and return to the ZaxNet Setup Menu.

  • Page 15: Firmware

    Each ERX is shipped with the latest firmware version installed. As newer firmware becomes available, it can be downloaded from the Zaxcom website: http://www.zaxcom.com/software-updates Newer version of beta firmware may be found on the Zaxcom forums: http://www.zaxcom.com/forum Each time an ERX is powered up, the firmware version number is displayed briefly on the LCD screen displayed as (VER X-XX).

  • Page 16: Updating Erx Firmware - Using An Trx Transmitter

    Zaxcom ERX3TCD Firmware Updating ERX firmware - using an TRX transmitter The TRX900 has to have the IFB option and needs to be running firmware version 7.02 1. Format a micro SD card in the TRX transmitter. 2. Using a computer with a SD card adapter, perform the following: •...

  • Page 17: Erx Specifications

    Zaxcom ERX3TCD Specifications ERX Specifications IFB Receiver RF Frequency Range: 2.403 to 2.475 GHz RF Modulation: Digital Spread Spectrum RF Frequency Step: 0.001 GHz (1 MHz) RF Bandwidth: 1 MHz Channel Separation: 2 MHz Sensitivity: -96 dBm DAC Bit-depth: 24 bit...

  • Page 18: Product Support

    Zaxcom ERX3TCD Support Product Support Register your product with Zaxcom: http://www.zaxcom.com/product-registration Download the latest Firmware from: http://www.zaxcom.com/software-updates Download the latest User Manuals from: http://www.zaxcom.com/instruction-manuals Submit Technical Questions at: http://www.zaxcom.com/submit-a-technical-question Submit information for Repair Services at: http://www.zaxcom.com/repairs Join the Zaxcom Forum at: http://www.zaxcom.com/forum...

  • Page 19: Zaxcom Warranty Policy And Limitations

    Distributers may sell Product to resellers who then sell Product to end users. Please see below for warranty information or obtaining service. No warranty service is provided unless the Product is returned to Zaxcom Inc. or a Zaxcom dealer in the region where the Product was first shipped by Zaxcom.

Table of Contents