Operation; Operating Instructions - A.J.Antunes VCT-250 Manual

operating instructions

. Set the Bun Thickness Adjustment Controls
(Figure 2a and 2b) according to the following
table:
for Mfg. No.: set the Crown
Control to:
920606
92066
920607
920608
92063
92065
920624
920626
table 1. bun thickness adjustment Control
settings
2. Turn the Rocker Switch (Power On/OFF) to
ON (Figure 3). Allow 30 minutes warm-up time
before proceeding.
Note: the temperature display (figure 4) will flash
"lo" until preset operating temperature is reached.
When the toaster approaches the preset tempera-
ture, "Use" will appear in the temperature display
and the unit is ready to toast buns.
The toaster is tested and shipped with the heaters set
at a preset recommended temperature. If "USE" does
not appear in the window after warm-up period, see
Temperature Adjustments below for recommended tem-
perature settings and to adjust temperature settings.
3. Drop buns into toaster (Figure 3). Cut sides of
heel and crown must face each other (heel/club
in front, crown in back).
4. Toasted product will drop into the bun landing
area (Figure 3).
5. Test at least 4 buns before putting toaster
into service.
6. Turn the Rocker Switch (Power On/Off) to OFF
when finished toasting.
P/N 00837 Rev. L 03/07
McDonald's

opeRatioN

and set the heel/
Club Control to:
3 B
4 E
5 D
5 D
5 D
5 D
5 D
5 D
Rapid toasteR VCt-250
CROWN
4
3 3
5
1
6
THICKNESS
1 = 9/16" (14.3mm)
2 = 5/8" (15.9mm)
3 = 11/16" (17.4mm)
4 = 3/4" (19.1mm)
5 = 13/16" (20.6mm)
6 = 7/8" (22.2mm)
figure 2a. bun thickness adjustment Controls for
Mfg. No.: 9210606 and 9210616
Note: background color of this label is GRaY.
CROWN
4
3
5
5
1
6
THICKNESS
1 = 9/16" (14.3mm)
2 = 5/8" (15.9mm)
3 = 11/16" (17.4mm)
4 = 3/4" (19.1mm)
5 = 13/16" (20.6mm)
6 = 7/8" (22.2mm)
figure 2b. bun thickness adjustment Controls for
Mfg. No.: 9210607, 608, 613, 624, & 626
Note: background color of this label is YelloW.
Bun Thickness
Adjustment
Controls
(See Figure 2)
Rocker Switch
(Power ON/OFF
Bun Landing
Area
figure 3. Rapid toaster
7
HEEL/CLUB
F
A
B E
2 B
C
D
THICKNESS
A = 3/8" (09.5mm)
B = 7/16" (11.1mm)
C = 1/2" (12.7mm)
D = 9/16" (14.3mm)
E = 5/8" (15.9mm)
F = 11/16" (17.4mm)
HEEL/CLUB
F
A
E
2
B
C
D
D
THICKNESS
A = 3/8" (09.5mm)
B = 7/16" (11.1mm)
C = 1/2" (12.7mm)
D = 9/16" (14.3mm)
E = 5/8" (15.9mm)
F = 11/16" (17.4mm)
heel/Club
Crown
Temperature Controls &
Switch)
Temperature Display