THE MACHINE UNTIL ALL THE INSTRUCTIONS HAVE BEEN READ AND UNDERSTOOD BY THE OPERATOR. FAILURE TO DO SO COULD RESULT IN SERIOUS BODILY INJURY AND/ OR PROPERTY DAMAGE! Kushlan Products, 281-313-2506 1-800-469-4178 12010 Dairy Ashford Road, Suite 160 Sugar Land, TX 77478...
Page 2
SHOULD YOU REQUIRE ANY SET-UP OR OPERATING ASSISTANCE WITH YOUR PROD- UCT, DO NOT RETURN TO ORIGINAL PLACE OF PURCHASE. After referring to the operation manual, if assistance is still needed, please consult our web Site at www.kushlanproducts.com From our web site you may e-mail us directly If assistance is still required, please call our customer service department at 1-800-469-4178 Safety Alert Symbol: This safety alert symbol is used to...
SAFETY INSTRUCTIONS For the safety of yourself and others around you, it is extremely important that you observe the following notes. 1. Keep hands and clothing away from moving parts at all times. 2. Do not operate this machine under the influence of alcohol or while taking medication that impairs the senses or reactions.
Page 4
KUSHLAN PRODUCTS, LLC Model 350WSB & 350WSB With Stand Parts List ITEM PART NO DESCRIPTION 350WSB 350WSB Wheelbarrow Mixer 35-1 Frame assembly 35-2 Polyethylene 3.5 cf drum with side holes 35-3 3/4 hp Electric motor with power cord 35-4 1 1/2" pulley 35-5 28"...
Page 6
KUSHLAN PRODUCTS, LLC Model 600W & 600W With Stand Parts List ITEM PART NO DESCRIPTION 600W 600W Wheelbarrow Mixer 60-1 Frame assembly 60-2 Polyethylene 6.0 cf drum 60-3 3/4 hp Electric motor with power cord 60-4 1 1/2" pulley 60-5 30"...
Page 8
Step 2. With the long end of wheel hub facing out assemble Step 1. Wheel Assembly Step 3. Install Wheels as shown, pushing axle rod end Step 4. Put washers on the axle, then fix R clips into out and the other end into the frame. holes.
Page 9
Placement of pinion gear Step 7. Slide drum on frame. Then install pinion housing. Line up front of pinion with front large gear Note: 600W drum has 3 blades as shown. (Note: Do not put pinion too far forward, so gear will not dig into drum.
Page 10
Step 12. Slide handle in place lining up the hole in the Step 13. Slide the pin through the holes. Soak Grips in handle and the housing. Slide the pin through the holes. boiling water for 1 minute to soften the heavy duty rubber.
Page 11
Optional Stand for 350/600 Mixer 3/8”x 1 1/2” Whizlock Screw 3/8”x 1 1/2” Whizlock Screw...
Page 12
WARNING Do not tilt mixer upright onto stand on a wet, uneven or slippery surface. Failure to fol- low this instruction could result in personal injury or damage to equipment. 3. Insert pivot tube of tri-pod stand assembly through pivot mount. (Figure 4) Figure 5–...
Page 13
Kushland Products, LLC Limited Warranty Policy Kushlan Products makes every effort to assure that its products meet high quality and durability standards and w a r r a n t s t o t h e o r ig i na l r et a i l c o n s u me r p u r c h a s e r o f o u r p ro d u ct s ( y o u ) t h a t ea c h s u ch product be free from defects in materials and workmanship as follows: ONE(1)YEAR limited warranty on motors.
Page 14
Model 350WSB & 350WSB With Stand Parts List ITEM PART NO DESCRIPTION 350WSB 350WSB WHEELBARROR MIXER 35-1 FRAME ASSEMBLY 35-2 POLYETHYLENE 3.5 DRUM WITH SIDE HOLES 35.3 3/4 HP MOTOR WITH POWER CORD 35-4 1 1/2” PULLEY 35-5 28” V-BELT 35-6 6”...
Need help?
Do you have a question about the 600 Series and is the answer not in the manual?
Questions and answers