Windows is a registered trademark of Microsoft Corporation. • In addition, the name of the software carried in this document and peripheral equipment is • each company’s trademark, or a registered trademark. Kyocera Corporation Revision 1.01 --- June.08.2006 - 4 -...
Page 5
Do not use or place the product at places with high humidity such as in the bath room or • near the humidifier. It may cause fire or electric shock. And do not touch the product with wet hands. Kyocera Corporation Revision 1.01 --- June.08.2006 - 5 -...
Page 6
Do not use it in the intense place of vibration. It becomes the cause of failure. • Kyocera Corporation Revision 1.01 --- June.08.2006 - 6 -...
Page 7
Data communication will be disabled or a data file may corrupt if the PC is turned off or the • product is separated from the PC during the communication. Important data must be verified against the original data. Kyocera Corporation Revision 1.01 --- June.08.2006 - 7 -...
This chapter This chapter describes what should be confirmed describes what should be confirmed before before using iBurst Modem using iBurst Modem..using iBurst using iBurst Modem Modem Kyocera Corporation Revision 1.01 --- June.08.2006 - 8 -...
UTC model Refer to the pictures shown below. Outlook of iBurst Outlook of iBurst Outlook of iBurst Outlook of iBurst Modem Modem Modem Modem UTC model Link/Communication Indicator Power Indicator External antenna port PC card connector Kyocera Corporation Revision 1.01 --- June.08.2006 - 9 -...
Meaning Power Indicator Turned OFF Blue Turned ON Fault Link/Communication Indicator Turned OFF Amber No signal receiving Yellow Weak signal receiving Blinking when communicating. Green Strong signal receiving Blinking when communicating. Kyocera Corporation Revision 1.01 --- June.08.2006 - 10 -...
2. Turn your PC on. 3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Setup starts. Click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 12 -...
Page 13
6. Click the [Next >] button after appearing dialog window as shown below. To install to a different folder, click [Browse…] and specify another folder. NOTE: 7. Click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 13 -...
Page 14
The iBurst Modem will be recognized and will be ready to use automatically. If the PC request to restart again, click [Yes] to restart the PC. NOTE: To connect to the Internet, refer to page 59. NOTE: Kyocera Corporation Revision 1.01 --- June.08.2006 - 14 -...
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Setup starts. Click the [Next >] button. 5. Select [I accept the terms the license agreement], click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 15 -...
Page 16
To install to a different folder, click [Browse…] and specify another folder. NOTE: 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation Revision 1.01 --- June.08.2006 - 16 -...
Page 17
The iBurst Modem will be recognized and will be ready to use automatically. If the PC request to restart again, click [Yes] to restart the PC. NOTE: To connect to the Internet, refer to page 64. NOTE: Kyocera Corporation Revision 1.01 --- June.08.2006 - 17 -...
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Setup starts. Click the [Next >] button. 5. Select [I accept the terms the license agreement], click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 18 -...
Page 19
To install to a different folder, click [Browse…] and specify another folder. NOTE: 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation Revision 1.01 --- June.08.2006 - 19 -...
Page 20
Select [Specify the location of the driver (Advanced)] and click the [Next >] button in the dialog window. The device name detected shall be; “Kyocera Corporation-iBurst Modem” or “Kyocera Corporation-iBurst Modem Type 02-01”. Kyocera Corporation Revision 1.01 --- June.08.2006 - 20 -...
Page 21
12. Select [Search for the best driver for your device.(Recommended)], then check [Specify a location] and click the [Browse] button. 13. Select [C:\Program Files\iBurst\bin], and click the [OK] button. 14. Click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 21 -...
Page 22
“iBurst Modem Type 02-01”. 17. The dialog window shown below will appear, click the [Yes] button, and restart your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. Kyocera Corporation Revision 1.01 --- June.08.2006 - 22 -...
Page 23
18. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Add New Hardware]. 19. Click the [Next >] button. 20. Click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 23 -...
Page 24
[Next >] button. 21. Select [No, I want to select the hardware from a list], and click the [Next >] button. 22. Select [Ports (COM & LPT)], and click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 24 -...
Page 25
23. Click the [Have Disk..] button. 24. Click the [Browse...] button. 25. Select [C:\Program Files\iBurst\bin], and click the [OK] button. You don’t have to select a file name. Windows will find an appropriate file NOTE: automatically. Kyocera Corporation Revision 1.01 --- June.08.2006 - 25 -...
Page 26
Modem Card Model (UTC) Manual iBurst Modem Card Model (UTC) Manual 26. Click the [OK] button. 27. Select [iBurst Virtual COM Port], and click the [Next >] button. 28. Click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 26 -...
Page 27
30. The dialog window shown below will appear, click the [Yes] button to SHUTDOWN SHUTDOWN your PC. SHUTDOWN SHUTDOWN NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. 31. Turn your PC on again. Kyocera Corporation Revision 1.01 --- June.08.2006 - 27 -...
Page 28
32. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Modems]. If the dialog window as shown below appears, click the [Add] button. NOTE: Kyocera Corporation Revision 1.01 --- June.08.2006 - 28 -...
Page 29
Modem Card Model (UTC) Manual 33. Check [Don’t detect my modem; I will select it from a list], and click the [Next >] button. 34. Click the [Have Disk...] button. 35. Click the [Browse…] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 29 -...
Page 30
You don’t have to select a file name. Windows will find an appropriate file NOTE: automatically. 37. Click the [OK] button. 38. Select [iBurst Virtual MODEM], and click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 30 -...
Page 31
If the dialog window as shown below appears, type a dummy number in “What NOTE: are (or city) code are you in now ?” and then click the [Next >] button. 40. Click the [Finish] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 31 -...
Page 32
Modem Card Model (UTC) Manual 41. Click the [OK] button. 42. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Network]. Kyocera Corporation Revision 1.01 --- June.08.2006 - 32 -...
Page 33
43. Click the [Add…] button on [Configuration] tab. The name of a network adaptor shall be; “iBurst Modem” or “iBurst Modem Type 02-01”. 44. Select [Protocol] and click the [Add…] button. 45. Click the [Have Disk…] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 33 -...
Page 34
You don’t have to select a file name. Windows will find an appropriate file NOTE: automatically. 48. Click the [OK] button. 49. Select [NDIS(PPPoE) Usermode I/O Protocol], click the [OK] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 34 -...
Page 35
51. The dialog window shown below will appear, click the [Yes] button, and restart your PC. If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. NOTE: To connect to the Internet, refer to page 64. NOTE: Kyocera Corporation Revision 1.01 --- June.08.2006 - 35 -...
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Setup starts. Click the [Next >] button. 5. Select [I accept the terms the license agreement], click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 36 -...
Page 37
To install to a different folder, click [Browse…] and specify another folder. NOTE: 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation Revision 1.01 --- June.08.2006 - 37 -...
Page 38
11. Confirm the device name indicated shall be [iBurst Modem] or [iBurst Modem Type 02-01]. Click the [Next >] button. The device name detected shall be; “Kyocera Corporation-iBurst Modem” or “Kyocera Corporation-iBurst Modem Type 02-01”. Kyocera Corporation Revision 1.01 --- June.08.2006 - 38 -...
Page 39
12. Select [Search for the best driver for your device.(Recommended)], and then check the [Next >] button. 13. Check [Specify a location] and click the [Browse] button. 14. Select [C:\Program Files\iBurst\bin], and click the [OK] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 39 -...
Page 40
The driver file name shall be; “NETIBST.INF” or “NETIBT21.INF”. If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] NOTE: into the CD-ROM drive and click the [OK] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 40 -...
Page 41
“iBurst Modem Type 02-01”. 18. The dialog window shown below will appear, click the [Yes] button, and restart your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. Kyocera Corporation Revision 1.01 --- June.08.2006 - 41 -...
Page 42
19. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Add New Hardware]. 20. Click the [Next >] button. 21. Click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 42 -...
Page 43
[Next >] button. 22. Select [No, I want to select the hardware from a list.], and click the [Next >] button. 23. Select [Ports (COM & LPT)], and click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 43 -...
Page 44
24. Click the [Have Disk..] button. 25. Click the [Browse…] button. 26. Select [C:\Program Files\iBurst\bin], and click the [OK] button. You don’t have to select a file name. Windows will find an appropriate file NOTE: automatically. Kyocera Corporation Revision 1.01 --- June.08.2006 - 44 -...
Page 45
Modem Card Model (UTC) Manual iBurst Modem Card Model (UTC) Manual 27. Click the [OK] button. 28. Select [iBurst Virtual COM Port], and click the [Next >] button. 29. Click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 45 -...
Page 46
31. The dialog window shown below will appear, click the [Yes] button to SHUTDOWN SHUTDOWN your PC. SHUTDOWN SHUTDOWN NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. Kyocera Corporation Revision 1.01 --- June.08.2006 - 46 -...
Page 47
33. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Modems]. If the dialog window as shown below appears, click the [Add] button. NOTE: Kyocera Corporation Revision 1.01 --- June.08.2006 - 47 -...
Page 48
34. Select [Other], and click the [Next >] button. 35. Check [Don’t detect my modem, I will select it from a list] and click the [Next >] button. 36. Click the [Have Disk…] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 48 -...
Page 49
You don’t have to select a file name. Windows will find an appropriate file NOTE: automatically. 39. Click the [OK] button. 40. Select [iBurst Virtual MODEM], and click the [Next >] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 49 -...
Page 50
If the dialog window as shown below appears, type a dummy number in “What NOTE: are (or city) code are you in now ?” and then click the [Next >] button. 42. Click the [Finish] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 50 -...
Page 51
Modem Card Model (UTC) Manual 43. Click the [OK] button. 44. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Network]. Kyocera Corporation Revision 1.01 --- June.08.2006 - 51 -...
Page 52
45. Click the [Add] button on [Configuration] tab. The name of a network adaptor shall be; “iBurst Modem” or “iBurst Modem Type 02-01”. 46. Select [Protocol] and click the [Add…] button. 47. Click the [Have Disk…] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 52 -...
Page 53
48. Click the [Browse…] button. 49. Select [C:\Program Files\iBurst\bin], and click the [OK] button. You don’t have to select a file name. Windows will find an appropriate file NOTE: automatically. 50. Click the [OK] button. Kyocera Corporation Revision 1.01 --- June.08.2006 - 53 -...