Table of Contents
Advertisement
START
TIMED MODE
MANUAL MODE
®
Loctite
Single CureJet
For Use With:
Part Number 1364033, LED Controller
Part Number 1369539, CureJet
Part Number 1369538, CureJet
Part Number 1369537, CureJet
Panasonic
TIMER
POWER
CURE LIGHT ON
UP
RESET
LOCK
LT4H
DOWN
FAULT
TM
TM
375
TM
405
TM
Indigo
Single CureJet™ Controller
Item # 1364033
For:
TM
LEDs
LED System
TM
EQUIPMENT
Operation Manual
Advertisement
Table of Contents
Related Manuals for Loctite Single CureJet
Summary of Contents for Loctite Single CureJet
- Page 1 EQUIPMENT Operation Manual Panasonic TIMER Single CureJet™ Controller POWER START Item # 1364033 CURE LIGHT ON TIMED MODE RESET LOCK LT4H DOWN FAULT For: MANUAL MODE LEDs ® Loctite Single CureJet LED System For Use With: Part Number 1364033, LED Controller...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. PLEASE OBSERVE THE FOLLOWING ....................3 ..........................3 MPHASIZED ECTIONS ............................3 TEMS UPPLIED ...........................3 AFETY , (I ) ....................4 IELD OF PPLICATION NTENDED SAGE 2. DESCRIPTION ...............................4 ..........................4 HEORY OF PERATION 1............4 PERATING LEMENTS AND ONNECTIONS REFERS TO IGURE 3. -
Page 3: Please Observe The Following
While the Loctite CureJet LED Light Sources have minimal output in the UV-A range, the ® use of UV safety glasses that conform to ANSI Z87.1/CSA Z94.3 (Such as Loctite P/N 98452) is recommended when operating the unit. WARNING! Never directly expose skin to light source. -
Page 4: Field Of Application, (Intended Usage)
The system is designed for intermittent or constant duty cycle. Description Theory of Operation 1364033 Single CureJet Controller will operate all existing CureJet Light Sources and all new CureJet Light Sources. - Page 5 11. To CureJet Connection ® The Loctite CureJet Controller must be connected to a CureJet LED to operate ® correctly. Use only Loctite Cables P/N 1370351 or 1370352 for interconnect. INPUT: RoHS TO CUREJET ™ 85-264 VAC Compliant 50 / 60 Hz Label P/N 8900605 MAX 2.7 A...
-
Page 6: Technical Data
(*Exact output measurement is dependent on the brand and calibration method of the meter used. ® These measurements were made with the Loctite UV-B&A LED Qualified Radiometer P/N 1390323 (375 Units) and Visible Light LED Dosimeter, P/N 1265282 (405 Units & Indigo... -
Page 7: Operating The Unit
B. Tapped inserts (E) on the bottom of the CureJet are for M4 screws. Do not thread screws deeper than .25 inches (6.35mm). ® 3. Using either Loctite Cables P/N 1370351 or 1370352, connect the CureJet to the LED Controller (Figure 2 Item C to Figure 1 Item 11). -
Page 8: Cure Light On Indicator
The Fault indicator will also light if the operating parameters, are outside of normal operation. Checking the Unit’s Output ® To check the unit’s output, insert the LED tip directly into Loctite UV-B&A LED Qualified Radiometer P/N 1390323 (375 Units), Visible Light LED Dosimeter, P/N 1265282 (405 Units &... -
Page 9: Care And Maintenance
It is recommended that the end of the light source be positioned no closer than 0.25” inch from ® the Loctite product being cured to minimize adhesive contamination on the light source tip. If adhesive should contaminate the light source tip, be sure to clean the light source tip to maximize the unit’s effective output. -
Page 10: Troubleshooting
• Replace fuses with 5x20mm 4 - Fuse is blown. Amp fast blow fuses. - Defective Switch. • Call 800-562-8483. Documentation Replacement Parts and Accessories Loctite Part Number Description 98452 Safety Glasses, Orange ® 1265282 Loctite Visible Light LED Qualified Radiometer Dosimeter ®... - Page 11 Canhema 09941-410 Madison Heights, MI 48071 Diadema/SP, Brazil www.loctite.com Loctite is a trademark of Henkel Corporation, U.S.A. © Copyright 2007. Henkel Corporation All rights reserved. Data in this operation manual is subject to change without notice. Manual P/N: 8902058, 11/2009...