Standard Equipment - Volvo Penta TAD734GE Manual

TAD734GE
Technical Data
General
Engine designation ...........................................................................TAD734GE
No. of cylinders and configuration ........................................................in-line 6
Method of operation ................................................................................4-stroke
Bore, mm (in.) ......................................................................................108 (4.25)
Stroke, mm (in.) ................................................................................... 130 (5.12)
Displacement, l (in³)....................................................................... 7.15 (436.0)
Compression ratio ..........................................................................................17:1
Dry weight, excl. cooling system, kg (lb) .................................... 764 (1684)
Wet weight, excl. cooling system, kg (lb) ....................................788 (1737)
Performance
with fan, kW (hp) at:
Prime Power
Max Standby Power
Lubrication system
Oil consumption, liter/h (US gal/h) at:
Prime Power
Max Standby Power
Oil system capacity incl filters, liter ............................................................... 29
Fuel system
Specific fuel consumption at:
Prime Power, g/kWh (lb/hph)
25 %
50 %
75 %
100 %
Max Standby Power, g/kWh (lb/hph)
25 %
50 %
75 %
100 %
Intake and exhaust system
Air consumption at 27°C, m³/min (cfm):
Prime Power
Max Standby Power
Max allowable air intake restriction,
kPa (In wc)
Heat rejection to exhaust,
kW (BTU/min) at:
Prime Power
Max Standby Power
Exhaust gas temperature after
turbine, °C (°F) at:
Prime Power
Max Standby Power
Max allowable back-pressure in
exhaust line, kPa (In wc)
Exhaust gas flow, m³/min (cfm) at:
Prime power
Max Standby Power
Cooling system
Heat rejection radiation from engine,
kW (BTU/min)
Prime Power
Max Standby Power
Heat rejection to coolant kW (BTU/min)
Prime Power
Max Standby Power
Fan power consumption, kW (hp)
Note! Not all models, standard equipment and accessories are available in all countries.
All specifications are subject to change without notice.
The engine illustrated may not be entirely identical to production standard engines.
Power Standards
The engine performance corresponds to ISO 3046, BS
5514 and DIN 6271. The technical data applies to an engine
without cooling fan and operating on a fuel with calorific value
of 42.7 MJ /kg (18360 BTU/lb) and a density of 0.84 kg/liter
(7.01 lb/US gal), also where this involves a deviation from
the standards. Power output guaranteed within 0 to +2% att
rated ambient conditions at delivery. Ratings are based on
ISO 8528.
Engine speed governing in accordance with ISO 3046/IV,
class A1 and ISO 8528-5 class G3
Exhaust emissions
The engine complies with EU stage 2 emission legislation
according to the Non Road Directive EU 97/68/EC.
1500 rpm 1800 rpm
213 (290) 216 (294)
238 (324) 243 (330)
1500 rpm 1800 rpm
0.03 (0.008) 0.03 (0.008)
0.03 (0.008) 0.03 (0.008)
1500 rpm 1800 rpm
244 (0.396) 257 (0.417)
233 (0.378) 237 (0.384)
217 (0.352) 222 (0.360)
204 (0.331) 205 (0.332)
247 (0.400) 259 (0.420)
235 (0.381) 239 (0.387)
217 (0.352) 225 (0.365)
205 (0.332) 207 (0.336)
1500 rpm 1800 rpm
16.1 (569) 18.3 (646)
16.3 (576) 18.9 (667)
3.0 (12.0) 3.0 (12.0)
160 (9099) 174 (9895)
177 (10066) 189 (10748)
495 (923) 475 (887)
550 (1022) 510 (950)
10 (40.2) 10 (40.2)
33.0 (1165) 36.7 (1296)
33.4 (1180) 37.9 (1338)
1500 rpm 1800 rpm
24 (1365) 25 (1422)
26 (1479) 28 (1592)
117 (6654) 124 (7052)
128 (7279) 137 (7791)
11.6 (16) 20.0 (27)
Rating Guidelines
PRIME POWER rating corresponds to ISO Standard Power for
continuous operation. It is applicable for supplying electrical power
at variable load for an unlimited number of hours instead of com-
mercially purchased power. A10 % overload capability for govering
purpose is available for this rating.
MAXIMUM STANDBY POWER rating corresponds to ISO Stan-
dard Fuel Stop Power. It is applicable for supplying standby electri-
cal power at variable load in areas with well established electrical
networks in the event of normal utility power failure. No overload
capability is available for this rating. 1 hp = 1 kW x 1.36
Information
For more technical data and information, please look in the Gener-
ating Set Engines Sales Guide.

Standard equipment

Engine
Automatic belt tensioner
Lift eyelets
Flywheel
Flywheel housing with conn. acc. to SAE 2
Flywheel 10" and 11.5" disc
Vibration damper
Engine suspension
Fixed integrated radiator front engine suspension
Lubrication system
Oil dipstick
Full-flow oil filter of cartridge type
Oil cooler, side mounted
Fuel system
Common rail
Fuel filters of cartridge type
Pre-filter with water separator
Intake and exhaust system
Two-stage air filter with cyclon
Connecting flange for exhaust pipe
Turbo charger, low left side
Cooling system
Tropical radiator incl intercooler
Belt driven coolant pump
Fan hub
Pusher fan
Fan guard
Belt guard
Control system
Engine Management System (EMS) with CAN-bus
interface SAE J1939 and stand alone interface
Alternator
Alternator 100A / 24 V
Starting system
Starter motor, 5.0kW, 24 V
Instruments and senders
Temp.- and oil pressure for automatic
stop/alarm
Engine Packing
Plastic wrapping
1)
must be ordered, se order specification
− optional equipment or not applicable
• included in standard specification
Dimensions TAD734GE
Not for installation
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1651
1858
1050
http://www.brizmotors.ru/equipment/ctm/
v250a/