Kenwood TK-5310 K4 Service Manual page 5

7. If writing ends successfully, the checksum is calculated
and a result is displayed.
8. If you want to continue programming other transceivers,
repeat steps 4 to 7.
Notes:
• This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming software.
• The text message are displayed for K2, K3, K5 and K6
models only.
• These transeivers use firmware versions F4.00 or later.
When using firmware versions earlier than version F4.00, a
"Check connection" error message will appear on the
LCD. Firmware versions earlier than version F4.00 will not
write to the transceiver.
6-4. Baud rate change
1. Change baud rate by changing the Concentric switch posi-
tion. The baud rates are assigned to positions of the Con-
centric switch as follows:
A: PROGRAM 115200 bps (The LED lights orange)
B: PROGRAM 57600 bps (The LED blinks orange)
C: PROGRAM 19200 bps (The LED blinks green)
2. If you press the [Side1] switch (top of left side) while the
baud rate (such as "PROGRAM 115200 bps") is displayed,
the checksum is calculated, and a result is displayed. If
you press the [Side1] switch again while the checksum is
displayed, the baud rate (such as "PROGRAM 115200
bps") is redisplayed.
Notes:
• Normally, write in the high-speed mode.
• The text message are displayed for K2, K3, K5 and K6
models only.
7. Clone Mode
(K2, K3, K5 and K6 models only)
Programming data can be transferred from one transceiver
to another by connecting them via their external universal con-
nectors. The operation is as follows (the transmit transceiver
is the source and the receive transceiver is a target).
The following data cannot be cloned.
• Tuning data
• Embedded message with password
• Model name data
• ESN (Electronic Serial Number) data
• Network file data (P25)
Key guide on the "INPUT PASSWORD" display.
• CNF([A] key): The password confirmation
• DEL([B] key): Delete the least digit from the current pass-
word number (Press and hold to delete all
password numbers)
• SET([D] key): Determine the least digit of the password number
1. Press and hold the [Side2] and [PTT] keys while turning the
transceiver power ON and then release the [Side2] key first.
If the Read authorization password is set to the transceiver,
the transceiver displays "CLONE LOCK". If the password is
not set, the transceiver displays "CLONE MODE".
2. When you enter the correct password, and "CLONE MODE"
is displayed, the transceiver can be used as the cloning
source. The following describes how to enter the password.
REALIGNMENT
3.
• How to enter the password using the keypad (K3 and
K6 models only);
If the [D] key is pressed while "CLONE LOCK" is displayed,
the Read authorization password input screen (INPUT
PASSWORD) is displayed.
If one of keys 0 to 9 is pressed while "INPUT PASSWORD"
is displayed, the pressed number is displayed on the LCD.
Each press of the key shifts the display in order to the left.
When you enter the password and press the [A] or [✳]
key, "CLONE MODE" is displayed if the entered pass-
word is correct. If the password is incorrect, "CLONE
LOCK" is redisplayed.
• How to enter the password using the [Side2] and
[Side3] keys (K2, K3, K5 and K6 models);
If the [D] key is pressed while "CLONE LOCK" is displayed,
the Read authorization password input screen (INPUT
PASSWORD) is displayed.
If the [Side2] key or [Side3] key is pressed while "INPUT
PASSWORD" is displayed, the number (0 to 9) flashes on
the LCD. When you press the [D] key, the currently
selected number is determined. If you press the [A] key
after entering the password in this procedure, "CLONE
MODE" is displayed if the entered password is correct. If
the password is incorrect, "CLONE LOCK" is redisplayed.
4. Power ON the target transceiver.
5. Connect the cloning cable (part No. E30-3325-05) to the
universal connectors on the source and target.
6. Press the [Side1] or [A] key on the source while the source
displays "CLONE MODE". The data of the source is sent
to the target. While the target is receiving the data, "PRO-
GRAM" is displayed. When cloning of data is completed,
the source displays "END", and the target automatically
operates in the User mode. The target can then be oper-
ated by the same program as the source.
7. The other target can be continuously cloned. When the
[Side1] or [A] key on the source is pressed while the
source displays "END", the source displays "CLONE
MODE". Carry out the operation in step 4 to 6.
Notes:
• Cannot be cloned if the password (overwrite password) is
programmed to the target.
• Cannot be cloned if the checksum in the Network File area of
the source transceiver and the target transceiver is different.
• "Model Name and Market Code" must be same to clone
the transceiver. However, it may be unable to clone the
transceiver depending on the enhanced features settings.
(Refer to the FPU for the enhanced features details.)
• Under certain conditions, clone mode cannot be activated
even if the clone mode of the source transceiver is set to
enable. Refer to the FPU for more details.
TK-5310
Cloning cable
(E30-3325-05)
Fig. 2
5