Subscribe to Our Youtube Channel
Related Manuals for Texas Instruments MSP432
Summary of Contents for Texas Instruments MSP432
- Page 1 MSP432™ Hardware Tools User's Guide Literature Number: SLAU571A March 2015 – Revised May 2016...
-
Page 2: Table Of Contents
1.2.1 Introduction ......................1.2.2 Key Features ......................1.2.3 Kit Contents ..................1.2.4 Configuration and Usage ....................1.2.5 Hardware Design .......................... Revision History Contents SLAU571A – March 2015 – Revised May 2016 Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated... - Page 3 1-2. MSP-FET-432ADPTR Bill of Materials ......................1-3. Device Compatibility .................... 1-4. Important Board Components ..................1-5. MSP-TS432PZ100 Bill Of Materials SLAU571A – March 2015 – Revised May 2016 List of Figures Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated...
-
Page 4: Preface
Preface SLAU571A – March 2015 – Revised May 2016 Read This First About This Manual This manual describes the hardware tools that support the Texas Instruments MSP432™ device family of Cortex -M based microcontrollers. ® ® How to Use This Manual This manual describes the setup and operation of the hardware tools. -
Page 5: Hardware
TI XDS100 and XDS200 debug probes is not included in this document, and can be found at www.ti.com/tool/xds100 and www.ti.com/tool/xds200, respectively..........................Topic Page .................... MSP-FET-432ADPTR ....................MSP-TS432PZ100 SLAU571A – March 2015 – Revised May 2016 Hardware Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated... -
Page 6: Introduction
1x MSP-FET-432ADPTR 14-pin JTAG to ARM adapter 1.1.4 Configuration and Usage The MSP-FET-432ADPTR allows the use of the MSP-FET debug probe with the MSP432 Cortex-M family of devices. Operation is straight-forward, with only one selection for how the power is sourced. This selection is required because of the difference in the power source and sense behavior of the MSP-FET and the ARM debug standard. -
Page 7: Hardware Design
MSP-FET-432ADPTR. L1 1 L2 3 L3 4 L4 6 Copyright © 2016, Texas Instruments Incorporated Figure 1-1. MSP-FET-432ADPTR Schematic Table 1-2 lists the bill of materials for the MSP-FET-432ADPTR. Table 1-2. MSP-FET-432ADPTR Bill of Materials... -
Page 8: Msp-Ts432Pz100
MCU after adding the tool to the TI Store cart: MSP432P401R. The MSP-TS432PZ100 is a stand-alone ZIF socket target board used to program and debug the MSP432 MCU in-system through the JTAG interface or the Serial Wire Debug (SWD 2-wire JTAG) protocol. Two standard ARM Cortex-M debug connectors provide connectivity to a large number of debug probes from Texas Instruments and third parties. -
Page 9: Board Configuration For External Target Power Supply
J2: Connect external VCC to pin 1, and external GND to pins 2 or 3 Feed external VCC here Feed external GND here Figure 1-2. Board Configuration For External Target Power Supply SLAU571A – March 2015 – Revised May 2016 Hardware Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated... -
Page 10: Board Configuration For Debugger-Supplied Target Power
If the debug probe supplies a logic level voltage through pin 19, the LDO can be entirely bypassed using JP15. Always follow the voltage limits defined in the device data sheet. Figure 1-3. Board Configuration For Debugger-Supplied Target Power Hardware SLAU571A – March 2015 – Revised May 2016 Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated... -
Page 11: Hardware Design
P6.4/UCB1SIMO/UCB1SDA/C1.3 P8.5/A20 P6.3/UCB1CLK/C1.4 P8.6/A19 P6.2/UCB1STE/C1.5 FE25-1A4 KX-7 QUARZ5 UART Copyright © 2016, Texas Instruments Incorporated Figure 1-4. MSP-TS432PZ100 Target Socket Board, Schematic SLAU571A – March 2015 – Revised May 2016 Hardware Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated... -
Page 12: Msp-Ts432Pz100 Target Socket Board, Pcb
JP15 Header to bypass 3V3 LDO in case a debug probe supplies a logic level voltage through pin 19 of header JA. Hardware SLAU571A – March 2015 – Revised May 2016 Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated... -
Page 13: Msp-Ts432Pz100 Bill Of Materials
3-pin header, male, TH SAM1035-03-ND DNP: Headers are enclosed J3, J4, J5, J6 25-pin header, TH SAM1029-25-ND in kit. Keep vias free of solder. SLAU571A – March 2015 – Revised May 2016 Hardware Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated... - Page 14 Geyer Electronic - 12.88710 30/30/50ppm EVQ-11L05R P8079STB-ND EVQ-11L05R P8079STB-ND TLV70033DDC, TSOT23-5 296-25276-2-ND 1.2.5.2 MSP-TS432PZ100 Revision History Revision Date Comments Rev1.1 March 2015 First released revision Hardware SLAU571A – March 2015 – Revised May 2016 Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated...
-
Page 15: Revision History
• Updated structure and headings throughout Section 1.2, MSP-TS432PZ100 ........• Removed entry for Rev1.0 from Section 1.2.5.2, MSP-TS432PZ100 Revision History SLAU571A – March 2015 – Revised May 2016 Revision History Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated... - Page 16 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue.
- Page 17 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments MSP-FET-432ADPTR...
Need help?
Do you have a question about the MSP432 and is the answer not in the manual?
Questions and answers