JUMBUCK TORINO CHARCOAL PIZZA OVEN (HS-GENS-209) SAFETY INSTRUCTIONS For outdoor use only. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. OUTDOOR Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
Page 3
OVEN OPERATING GUIDELINES Cleaning Lighting the oven once finish cooking, remove left over solid fuel solid fuel is to be used for this product (fire ashes can be removed via the charcoal drawer wood, charcoal etc.) place solid fuel onto the charcoal grid and light ...
PARTS CODE Part Number Part Name Supplier Code Chimney Cover GENS209-01 Chimney GENS209-02 Chimney Vent GENS209-03 Oven Body GENS209-04 Temperature Gauge GENS209-05 Oven Door GENS209-06 Door Handle Bracket GENS209-07 Door Handle GENS209-08 Door Axle GENS209-09 Charcoal Compartment Door Vent GENS209-10 Charcoal Compartment Door GENS209-11 Charcoal Drawer...
ASSEMBLY INSTRUCTIONS Remove all contents from packaging, and make sure all the parts are present before attempting to assemble! Tighten all bolt connections by hand first. When the oven is fully assembled, retighten the screws, nuts and bolts by using a wrench and screwdriver. STEP 1 Assemble the Short Legs (Part 14) and Long Legs (Part 15) onto the Shelf (Part 16) as per illustration below.
STEP 3 Assemble the Wheels (Part 17) onto the Wheel Axle (Part 4) as per illustration below. Use Nut E to secure. STEP 4 Assemble the Oven Body (Part 3) onto the Bottom Panel (Part 11) as per illustration below. Use Bolt B and Nut C to secure.
Page 10
STEP 5 Install the Chimney Cover (Part 1) to the Chimney (Part 2) as per illustration below. Use Bolt B to secure. STEP 6 Install the Chimney (Part 2) onto the Oven Body (Part 3) as per illustration below. Use Bolt B and Nut C to secure.
STEP 7 Install the Side Handle (Part 13) onto the Body as per illustration below. Use Bolt A and Flat Washer F to secure. STEP 8 Assemble the Oven Door (Part 5) onto the Oven Body (Part 3) by inserting the Door Axle (Part 6) as per illustration below.
STEP 9 Assemble the Charcoal Compartment Door (Part 7) onto the Oven Body (Part 3) by inserting the Door Axle (Part 6) as per illustration below. Use the Cotter Pin (Part D) and Plug Pin (Part G) to secure. STEP 10 Place the Charcoal Drawer (Part 8) into the Oven Body (Part 3) as per illustration below.
STEP 11 Place the Cooking Rack (Part 9) and Charcoal Grid (Part 10) into their respective compartments as per illustration below. STEP 12 Place the Ceramic Stone Plate (Part 12) onto the Cooking Rack (Part 9) as per illustration below.
Page 14
Fully-Assembled Your oven is now ready for use. Please take care when lighting your oven. Always keep children away from this oven at all times.
Page 15
The warranty for New Zealand is given by : the operating manual. Bunnings NZ Limited Any repair does not extend the warranty period. PO Box 14436, Any parts other than original Jumbuck parts will Panmure, Auckland, 1471 void this warranty. NEW ZEALAND (09) 978 2200 marketing@bunnings.co.nz...
Page 16
WARRANTY For New Zealand Customer For Australian Customers Any claim under this warranty must be made Any claim under this warranty must be made within 12 months of the date of purchase of the within 12 months of the date of purchase of the product.
Page 17
Liability will only be accepted for loss or damage technical issues with your JUMBUCK OVEN, in the first instance review the instructions manual or during transit if at the time the product was being...
Need help?
Do you have a question about the TORINO and is the answer not in the manual?
Questions and answers