Mitsubishi Electric FR-A741-5.5K Installation Manualline page 26

PARAMETER
Parameter Name
Speed feed for-
ward control/
877
model adaptive
speed control
selection
Speed feed for-
878
ward filter
Speed feed for-
879
ward torque limit
880
Load inertia ratio 0 to 200
Speed feed for-
881
ward gain
Regeneration
882
avoidance opera-
tion selection
Regeneration
883
avoidance opera-
tion level
Regeneration
avoidance at
884
deceleration
detection sensi-
tivity
Regeneration
avoidance com-
885
pensation fre-
quency limit
value
Regeneration
886
avoidance volt-
age gain
888
Free parameter 1
889
Free parameter 2
Cumulative
power monitor
891
digit shifted
times
892
Load factor
Energy saving
monitor refer-
893
ence (motor
capacity)
Control selec-
tion during com-
894
mercial power-
supply operation
Power saving
895
rate reference
value
896
Power unit cost
Power saving
897
monitor average
time
Power saving
898
cumulative moni-
tor clear
Operation time
899
rate (estimated
value)
20
Setting Range Initial Value
0, 1, 2 0
0 to 1s 0s
0 to 400% 150%
7
0 to 1000% 0%
0, 1, 2 0
300 to 800V 780V DC
0 to 5 0
0 to 10Hz, 9999 6Hz
0 to 200% 100%
9999
0 to 9999
9999
0 to 4, 9999 9999
30 to 150% 100%
Inverter
0.1 to 55kW rated
capacity
0, 1, 2, 3 0
0, 1, 9999 9999
0 to 500, 9999 9999
0, 1 to 1000h,
9999
9999
0, 1, 10, 9999 9999
0 to 100%, 9999 9999
Parameter Name
C0
FM terminal
*3 calibration
(900)
C1
AM terminal
*3
calibration
(901)
C2
Terminal 2 frequency
*3
setting bias frequency
(902)
C3
Terminal 2 frequency
*3 setting bias
(902)
125
Terminal 2 frequency
*3
setting gain frequency
(903)
C4
Terminal 2 frequency
*3 setting gain
(903)
C5
Terminal 4 frequency
*3 setting bias frequency
(904)
C6
Terminal 4 frequency
*3
setting bias
(904)
126
Terminal 4 frequency
*3 setting gain frequency
(905)
C7
Terminal 4 frequency
*3
setting gain
(905)
C12
Terminal 1 bias fre-
*3
quency (speed)
(917)
C13
Terminal 1 bias
*3 (speed)
(917)
C14
Terminal 1 gain
*3
frequency (speed)
(918)
C15
Terminal 1 gain
*3
(speed)
(918)
C16 Terminal 1 bias com-
mand (torque/mag-
*3
(919)
netic flux)
C17
Terminal 1 bias
*3
(torque/magnetic flux)
(919)
C18
Terminal 1 gain com-
mand (torque/mag-
*3
(920)
netic flux)
C19
Terminal 1 gain
*3
(torque/magnetic flux)
(920)
C38
Terminal 4 bias com-
mand (torque/mag-
*3
(932)
netic flux)
Setting Range Initial Value
— —
— —
0 to 400Hz 0Hz
0 to 300% 0%
0 to 400Hz 60Hz
0 to 300% 100%
0 to 400Hz 0Hz
0 to 300% 20%
0 to 400Hz 60Hz
0 to 300% 100%
0 to 400Hz 0Hz
0 to 300% 0%
0 to 400Hz 60Hz
0 to 300% 100%
0 to 400% 0%
0 to 300% 0%
0 to 400% 150%
0 to 300% 100%
0 to 400% 0%