Mitsubishi Electric FR-A741-5.5K Installation Manualline page 24

PARAMETER
Parameter Name
*2
479 Lower 4 digits
*2
480 Upper 4 digits
*2
481 Lower 4 digits
*2
482 Upper 4 digits
*2
483 Lower 4 digits
*2
484 Upper 4 digits
*2
485 Lower 4 digits
*2
486 Upper 4 digits
*2
487 Lower 4 digits
*2
488 Upper 4 digits
*2
489 Lower 4 digits
*2
490 Upper 4 digits
*2
491 Lower 4 digits
*2
492 Upper 4 digits
*2
493 Lower 4 digits
*2
494 Upper 4 digits
Remote output
495
selection
496
Remote output data 1 0 to 4095
497
Remote output data 2 0 to 4095
503
Maintenance timer
Maintenance timer
504
alarm output set time
Speed setting
505
reference
S-pattern time at
516
a start of acceler-
ation
S-pattern time at
517
a completion of
acceleration
S-pattern time at
518
a start of deceler-
ation
S-pattern time at
519
a completion of
deceleration
Modbus-RTU
539
communication check
time interval
547
Parameter for manufacturer setting. Do not set.
548
18
Setting Range Initial Value
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0 to 9999 0
0, 1, 10, 11 0
0
0
0 (1 to 9998) 0
0 to 9998, 9999 9999
1 to 120Hz 60Hz
0.1 to 2.5s 0.1s
0 to 999.8s,
9999
9999
Parameter Name
Protocol selec-
549
tion
NET mode opera-
550
tion command
source selection
PU mode opera-
551
tion command
source selection
Current average
555
time
Data output mask
556
time
Current average
value monitor
557
signal output ref-
erence current
Energization time
563
carrying-over times
Operating time
564
carrying-over times
Second motor speed
569
control gain
571
Holding time at a start
Second motor online
574
auto tuning
Output interrup-
575
tion detection
time
Output interrup-
576
tion detection
level
Output interrup-
577
tion cancel level
Acceleration time at a
611
restart
Regeneration
665
avoidance frequency
gain
Tuning data unit
684
switchover
Control method
800
selection
Pre-excitation
*2
802
selection
Constant power
range torque
803
characteristic
selection
Torque command
804
source selection
Torque command
805
value (RAM)
Torque command
806
value (RAM,
EEPROM)
807
Speed limit selection
Forward rotation
808
speed limit
Reverse rotation
809
speed limit
Setting Range Initial Value
0, 1 0
0, 1, 9999 9999
1, 2 2
0.1 to 1.0s 1s
0.0 to 20s 0s
Rated
inverter
0 to 500A
output
current
(0 to 65535) 0
(0 to 65535) 0
0 to 200%, 9999 9999
0.0 to 10.0s,
9999
9999
0, 1 0
0 to 3600s, 9999 1s
0 to 400Hz 0Hz
900 to 1100% 1000%
0 to 3600s, 9999 5s
0 to 200% 100
0, 1 0
0 to 5, 9 to 12,
20
20
0, 1, 0
0, 1 0
0, 1, 3 to 6 0
600 to 1400% 1000%
0, 1, 2 0
0 to 120Hz 60Hz
0 to 120Hz, 999 9999