Table of Contents
Related Manuals for BEA LZR-H100
Summary of Contents for BEA LZR-H100
- Page 1 -H100 ® LASER SCANNER FOR BARRIERS & GATES with max. detection range of 32’ × 32’ User’s Guide Visit website for available languages of this document. 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221 Page 1 of 1 Page 1 of 1...
-
Page 2: Installation And Maintenance
This device is not intended for use in with any automatically activated doors. US Pat. No. 7,084,388, which is not owned by BEA, covers automatic doors comprising, among other things, a scanning detector. The LZR-H100 is not sold with consent, implied or otherwise, for use with automatically activated doors, as set forth in the aforementioned patent. -
Page 3: Led Signals
This can be useful in cases where the sensor should not draw any attention. SYMBOLS Caution! Important Good to know Factory values Laser radiation Important remote control Possible remote control sequence adjustments 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221 Page 3 of 6 Page 3 of 6... -
Page 4: Basic Principles
In order to maximize safety for mixed traffic (vehicles and trucks), an additional vertical detection zone is recommended (LZR-I30). Page 4 of 6 Page 4 of 6 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221... -
Page 5: Application Requirements
APPLICATION REQUIREMENTS These requirements ensure optimal safety of the barrier in order to protect against contact with the barrier. DOUBLE ACCESS LANE 90° 45° • 2 LZR-H100 • 2 references, 1 for each sensor 0° SINGLE ACCESS LANE 90° 45°... -
Page 6: How To Use The Remote Control
SAVING AN ACCESS CODE The access code is recommended for sensors installed close to each other. DELETING AN ACCESS CODE Enter the existing code DELETING AN UNKNOWN ACCESS CODE Page 6 of 6 Page 6 of 6 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221... -
Page 7: Recommended Mounting
(in) h (in) Ensure there are no obstructions in front of the Do not cover the front face of the sensor with sensor! glass or plastic. 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221 Page 7 of 16 Page 7 of 16... -
Page 8: Mounting And Wiring
LED signal at power-on: Correct positioning is needed Safety and opening detection Power on without test signal: Connect blue/white and blue wires to test or power supply. Page 8 of 16 Page 8 of 16 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221... -
Page 9: Field Positioning
- The beginning of the opening field should be field with the hex key if necessary. approximately 15 inches above the ground. To finish, lock the sensor position. 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221 Page 9 of 16 Page 9 of 16... - Page 10 For best detection performance, use teh sensor with the reference point. By default, the sensor automatically adjusts the width of the safety field based on the reference. Page 10 of 16 Page 10 of 16 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221...
- Page 11 The safety field is necessary for the correct functioning of the installation. If the safety field is badly adjusted, the manufacturer of the sensor cannot be held responsible for inappropriate functioning of the installation. Always verify the correct functioning of the safety field before leaving the premisses. 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221 Page 11 of 16...
- Page 12 Always launch a new teach-in after adjusting the field dimensions. Page 12 of 16 Page 12 of 16 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221...
-
Page 13: Remote Control Adjustments
P – NC P – NC A – NO R1 R2 RELAY 2 P – NC A – NO P – NC A – NO FACTORY VALUE 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221 Page 13 of 16 Page 13 of 16... - Page 14 IMMUNITY NOTE: Select "high" if fog is causing unwanted detections. standard high MAGIC WAND teach-in teach-in factory visible safety field opening field values laser beams Page 14 of 16 Page 14 of 16 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221...
-
Page 15: Troubleshooting
Sensor does not unlock Access code needs entered or Cycle power supply. an incorrect code was used No code is required to unlock during the first minute after powering. 75.5984.01 LZR-H100 20181221 75.5984.01 LZR-H100 20181221 Page 15 of 16 Page 15 of 16... -
Page 16: Technical Specifications
BEA strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and factory- trained for the type of door/gate system.