Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HIKOKI C 18DBAL
Summary of Contents for HIKOKI C 18DBAL
- Page 1 C 18DBAL Handling instructions...
-
Page 2: General Power Tool Safety Warnings
power source and/or battery pack, picking up or GENERAL POWER TOOL SAFETY carrying the tool. WARNINGS Carrying power tools with your fi nger on the switch or energising power tools that have the switch on WARNING invites accidents. Read all safety warnings and all instructions. d) Remove any adjusting key or wrench before Failure to follow the warnings and instructions may result in turning the power tool on. - Page 3 c) When battery pack is not in use, keep it away - when the blade is pinched or bound tightly by the kerf from other metal objects, like paper clips, coins, closing down, the blade stalls and the motor reaction keys, nails, screws or other small metal objects, drives the unit rapidly back toward the operator;...
-
Page 4: Additional Safety Warnings
When blade is binding, or when interrupting a cut for any d) Always observe that the lower guard is covering the reason, release the trigger and hold the saw motionless blade before placing saw down on bench or fl oor. in the material until the blade comes to a complete An unprotected, coasting blade will cause the saw to stop. -
Page 5: Regarding Lithium-Ion Battery Transportation
1. When the battery power remaining runs out, the motor REGARDING LITHIUM-ION BATTERY stops. TRANSPORTATION In such a case, charge it up immediately. 2. If the tool is overloaded, the motor may stop. In this When transporting a lithium-ion battery, please observe the case, release the switch of tool and eliminate causes of following precautions. -
Page 6: Standard Accessories
Read all safety warnings and all instructions. Weight 3.4 kg (BSL1860) Always wear eye protection. NOTE Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to Always wear hearing protection. change without prior notice. Rated voltage... - Page 7 Electronic control CHARGING ○ Soft-start ○ Overload protection Before using the power tool, charge the battery as follows. This protection feature cuts off the power to the motor 1. Connect the charger's power cord to the receptacle. in the event of overloading of motor or a conspicuous (Fig.
- Page 8 4 – 10 the pilot lamp or charge indicator lamp to blink in red NOTE (every second), please take the charger to the HiKOKI The recharging time may vary according to the ambient Authorized Service Center. temperature and power source voltage.
-
Page 9: Mounting And Operation
MOUNTING AND OPERATION ABOUT THE KICKBACK REDUCTION SYSTEM Action Figure Page This product is equipped with a Kickback Reduction System Fine tuning of parallelism that monitors changes in the motor’s rotation speed and Fine tuning of perpendicularity stops the motor the instant it detects a sudden drop in speed due to the saw blade becoming bound, etc. - Page 10 In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. Important notice on the batteries for the HiKOKI cordless power tools Please always use one of our designated genuine batteries. We cannot guarantee the safety and...
- Page 11 5 mm 2.5 mm C18DBAL C18DBAL (NN) – – – –...
- Page 12 &...
- Page 14 45° 0° 1 + 2 =...
- Page 15 & 〈UC18YFSL〉 〈UC18YSL3〉...
- Page 16 45° 30° 15° 0°...
- Page 19 18V (Li – ion) UC18YFSL (14.4V – 18V) UC18YSL3 (14.4V – 18V) 329897 338915 338916 338917 990666 944459 302756 339383 316161 339188 337528 373651...
- Page 20 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99712613 G Printed in China...
Need help?
Do you have a question about the C 18DBAL and is the answer not in the manual?
Questions and answers