Smeg PX140 Instruction Manual
  1. Manuals
  2. Brands
  3. Smeg Manuals
  4. Cooktop
  5. PX140
  6. Instruction manual

Smeg PX140 Instruction Manual

Smeg gas cooktop instruction manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1. Precautions for safety and use________________________ 20
2. Fitting the appliance in the top ________________________ 21
2.1 Fixing to the supporting structure _______________________________________21
2.2 Fitting the gasket ___________________________________________________22
2.3 Fixing using brackets ________________________________________________22
3. Electrical connection _______________________________ 23
4. Gas connection ___________________________________ 24
4.1 Bottled gas connection _______________________________________________24
4.2 Room ventilation ____________________________________________________24
4.3 Combustion gas discharge ____________________________________________24
5. Adapting to different types of gas______________________ 25
5.1 Removing the hob skin _______________________________________________25
5.2 Adjusting for bottled gas ______________________________________________26
5.3 Adjusting for natural gas ______________________________________________27
5.4 Adjusting the primary air flow __________________________________________27
5.5 Reassembling the hob skin____________________________________________28
5.6 Adjusting the minimum for natural gas ___________________________________28
5.7 Adjusting the minimum for bottled gas ___________________________________28
5.8 Hob burner layout ___________________________________________________28
5.9 Greasing the gas taps________________________________________________28
6. Description of controls ______________________________ 29
6.1 The front panel _____________________________________________________29
7. Using the hob _____________________________________ 30
7.1 Fitting the Pan Stands _______________________________________________30
7.2 Lighting burners with safety device______________________________________32
7.3 Practical hints for using the burners _____________________________________32
7.4 Pan diameters______________________________________________________33
8. Cleaning and maintenance __________________________ 34
8.1 Cleaning the hob____________________________________________________34
8.2 Cleaning the components _____________________________________________34
THESE INSTRUCTIONS ONLY APPLY TO THE COUNTRIES OF DESTINATION WHOSE
IDENTIFICATION SYMBOLS ARE LISTED ON THE COVER OF THIS MANUAL.
THIS BUILT-IN HOB IS CLASSIFIED AS CLASS 3.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
engineer who is to check the gas supply system and install, commission and test the
appliance.
INSTRUCTIONS FOR THE USER: these provide recommendations for use, a
description of the controls and the correct procedures for cleaning and maintaining the
appliance.

Table of Contents

19

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PX140 and is the answer not in the manual?

Questions and answers

Related Manuals for Smeg PX140

Summary of Contents for Smeg PX140

  • Page 1: Table Of Contents

    Table of Contents 1. Precautions for safety and use________________________ 20 2. Fitting the appliance in the top ________________________ 21 2.1 Fixing to the supporting structure _______________________________________21 2.2 Fitting the gasket ___________________________________________________22 2.3 Fixing using brackets ________________________________________________22 3. Electrical connection _______________________________ 23 4.

  • Page 2: Precautions For Safety And Use

    Precautions for Safety and Use Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB.

  • Page 3: Instructions For The Installer

    Instructions for the Installer Fitting the appliance in the top The procedures required below must be carried out by a skilled builder and/or joiner. The hob can be installed on various materials, including masonry, metal, solid wood and wood finished with plastic laminates, provided the material is heat-resistant (T 90° 2.1 Fixing to the supporting structure Make a hole in the cabinet top with the dimensions shown here, maintaining a distance of at least 100 mm from the rear edge.

  • Page 4: Fitting The Gasket

    Instructions for the Installer 2.2 Fitting the gasket Fit the insulating gasket provided carefully around the outside edge of the hole made in the top as shown below, pressing it down with your hands so that its entire surface fits snugly. Follow the dimensions shown, bearing in mind that the long front edge must be flush with the hole.

  • Page 5: Electrical Connection

    Instructions for the Installer Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations.

  • Page 6: Gas Connection

    Instructions for the Installer Gas connection If the appliance is installed above an oven, the gas hose must be passed around the back of the oven to prevent overheating. The connection to the gas mains may be made using a copper pipe or a continuous-wall steel hose in accordance with the relevant regulations.

  • Page 7: Adapting To Different Types Of Gas

    Instructions for the Installer Adapting to different types of gas The operations described below must be carried out with the appliance not connected to the gas supply. The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. If it is to be used with other types of gas, the burner nozzles have to be changed and the primary air flow adjusted.

  • Page 8: Adjusting For Bottled Gas

    Instructions for the Installer 5.2 Adjusting for bottled gas Undo the screw C and push the air regulator D fully down. Remove the nozzle E with a 7 mm spanner and fit the suitable one, following the instructions in the tables referring to the type of gas to be used.

  • Page 9: Adjusting For Natural Gas

    Instructions for the Installer 5.3 Adjusting for natural gas The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. To return the appliance to the condition required to use this type of gas, proceed as described in point “5.2 Adjusting for bottled gas”...

  • Page 10: Reassembling The Hob Skin

    Instructions for the Installer 5.5 Reassembling the hob skin Reverse the procedure described in point “5.1 Removing the hob skin”. Fit the pan stands as described in point “7.1 Fitting the Pan Stands”. 5.6 Adjusting the minimum for natural gas Reassemble the components on the burner and fit the knobs onto the tap rods.

  • Page 11: Description Of Controls

    Instructions for the Installer Description of controls 6.1 The front panel All the hob's control and monitoring devices are placed together on the front panel. KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol .

  • Page 12: Instructions For The User

    Instructions for the User Using the hob Check that the burners, flame diffuser rings and pan stands are fitted correctly. The projections A on the flame diffuser rings must be fitted into the recesses B in the burner. The holes C in the burner must mate with the ignition plugs and thermocouples D on the hob.
  • Page 13 Instructions for the User hob. Make sure that the pan stands are simply fitted over their burners, and are not left in a raised or tilted position; if this occurs, repeat the fitting procedure. WRONG WRONG After performing the operations described above (for each pan stand), the hob will be as shown below, with the feet of the pan stands forming a pattern of horizontal and vertical lines.

  • Page 14: Lighting Burners With Safety Device

    Instructions for the User 7.2 Lighting burners with safety device The burner it controls is shown next to each knob (the example here shows the front left-hand burner). The appliance is equipped with electronic ignition. Simply press the knob and turn it anti-clockwise to the minimum flame symbol pressed down for about 2 seconds to keep the flame alight and prime the safety device.

  • Page 15: Pan Diameters

    Instructions for the User 7.4 Pan diameters BURNERS min. and max. Ø (in cm) 1 Auxiliary 2 Semi rapid 3 Rapid 4 Ultra rapid 7-18 10-24 18-24 20-26...

  • Page 16: Cleaning And Maintenance

    Instructions for the User Cleaning and maintenance Before carrying out any operations, disconnect the appliance from the electricity supply. Never use a jet of steam for cleaning the appliance. 8.1 Cleaning the hob To keep the hob in good condition, it must be cleaned regularly, after each use, first allowing it to cool.

This manual is also suitable for:

Px140bePx140dPx140nl

Table of Contents