Luxul Xen XAP-1040 User Manual
  1. Manuals
  2. Brands
  3. Luxul Manuals
  4. Wireless Access Point
  5. Xen XAP-1040
  6. User manual

Luxul Xen XAP-1040 User Manual

High performance outdoor 802.11b/g/n wireless access point
Hide thumbs Also See for Xen XAP-1040:
Table of Contents

Advertisement

Quick Links

Download this manual
Luxul Xen™ High Performance Outdoor
802.11b/g/n Wireless Access Point
Use the XAP-1040 to:
Provide„a„High„Performance„Outdoor„802.11n„Wi-Fi„Network„„
„
„
Setup„a„Superior„Point-to-Point„or„Point-to-Multipoint„Bridge„Link„
„
„
AP
Increase„Mobile„Client„Device„Network„Sensitivity„and„Performance
„
„
Simplify„Installation„While„Minimizing„Setup„Time„and„Expense„
„
„
Eliminate„Client„Device„Roaming„Issues
„
„
luxul.com
Simply Connected
User Guide
XAP-1040

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Xen XAP-1040 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Luxul Xen XAP-1040

Summary of Contents for Luxul Xen XAP-1040

  • Page 1 Simply Connected User Guide XAP-1040 Luxul Xen™ High Performance Outdoor 802.11b/g/n Wireless Access Point Use the XAP-1040 to: Provide„a„High„Performance„Outdoor„802.11n„Wi-Fi„Network„„ „ „ Setup„a„Superior„Point-to-Point„or„Point-to-Multipoint„Bridge„Link„ „ „ Increase„Mobile„Client„Device„Network„Sensitivity„and„Performance „ „ Simplify„Installation„While„Minimizing„Setup„Time„and„Expense„ „ „ Eliminate„Client„Device„Roaming„Issues „ „ luxul.com...
  • Page 2 This„product„is„covered„by„one„or„more„U.S.„and„foreign„patents„Patents:„7,379,717,„ 6,606,075,„6,373,448,„other„patents„pending dOcUment cOnventiOns The„following„graphical„alerts„are„used„in„this„document„to„indicate„notable„situations: NOTE:„„ T ips,„hints,„or„special„requirements„that„you„should„take„note„of. „ CAUTION:„„ C are„is„required.„Disregarding„a„caution„can„result„in„data„ loss„or„equipment„malfunction. „ WARNING!: Indicates„a„condition„or„procedure„that„could„result„in„ personal„injury„or„equipment„damage. „ fcc cOmPLiAnce This„device„complies„with„Part„15„of„the„FCC„Rules.„Operation„is„subject„to„the„ following„two„conditions:„(1)„this„device„may„not„cause„harmful„interference,„and„(2)„ this„device„must„accept„any„interference„received,„including„interference„that„may„ cause„undesired„operation. © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 3: Table Of Contents

    6.2 RF Exposure Guidelines 6.3 Radio Frequency Interference Requirements—FCC 6.4 Radio Transmitters (Part 15) 6.5 Industry Canada (RSS-Gen Issue 2) APPendiX 1: tecHnicAL sUPPOrt luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 4: Introduction

    Highest„FCC„Approved„Performance„(Effective„EIRP„36dBm)„for„Farther„Reaching„ „ Signal„and„Maximum„Data„Rates„ 18dB„of„Receive„Gain„Increases„Client„Device„Network„Sensitivity„and„ „ Performance Complies„with„2.4„GHz„IEEE„802.11n„Standard.„Backward„Compatible„with„IEEE„ „ 802.11g/b„ Supports„WMM„QoS„Functionality„to„Prioritize„Multimedia„Traffic„ „ Enhanced„Multi-Level„Security„with„WPA-PSK„(TKIP,„AES,„TKIP„&„AES),„WPA2-PSK„ „ (AES),„WPA-PSK/WPA2-PSK„Personal„(TKIP„&„AES)„and„128-bit„WEP„ Supports„up„to„8„SSIDs„with„Individual„Security„Settings „ Multiple„SSIDs„Support„VLAN„Tagging„(1„VLAN„per„SSID) „ Single„Cable„Installation„with„PoE„(supports„both„IEEE„802.3af„and„Legacy)„ „ Firmware„Upgradeable„ „ Easy„3„Step„Setup„through„Web-based„XenSmart™„User„Interface „ © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 5: Warnings

    „ the„FCC„Rules. 1.2 Site Preparation Consult„your„site„survey„and„network„analysis„reports„to„determine„specific„ „ equipment„placement,„power„drops,„and„so„on. Assign„installation„responsibility„to„the„appropriate„personnel. „ Identify„and„document„where„all„installed„components„are„located. „ Provide„a„sufficient„number„of„power„drops„for„your„equipment. „ Ensure„adequate,„dust-free„ventilation„to„all„installed„equipment. „ Identify„and„prepare„Ethernet„and„console„port„connections. „ Verify„that„cable„lengths„are„within„the„maximum„allowable„distances„for„optimal„ „ and„certified„signal„transmission. luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 6: Xap-1040 Specifications

    „ Security WEP„(128„bit)„ „ „ WPA-PSK„(TKIP,„AES,„TKIP&AES) „ „ WPA2-PSK„(AES) „ „ WPA-PSK/WPA2-PSK„Auto„(TKIP&AES) „ „ Web„Based„Firmware„Upgrade „ „ QoS:„Wireless„Multi-Media„(WMM)„Extensions „ „ Certifications FCC„Part„15,„Class„B „ „ © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 7: Getting Started

    „ Internet„Connection„to„View„Documentation„Online „ 3.2 Package Contents XAP-1040„Wireless„Access„Point „ Weather„Resistant„RJ45„Connector„Gland „ POE„Injector,„Power„Adapter,„Noise„Suppresser„ „ Dual„Purpose„Mounting„Bracket„for„Wall„or„Pole „ Quick„Install„Guide „ NOTE: If„any„of„the„listed„items„are„missing„or„damaged,„please„contact„ the„reseller„from„whom„you„purchased„for„return/replacement.„ „ „ luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 8: Safety Information

    The„XAP-1040„contains„no„user-serviceable„parts.„If„the„access„point„is„not„ „ working„properly,„contact„your„dealer„and„ask„for„help.„DO„NOT„attempt„to„ disassemble„the„access„point. 4 HARdWARE FEATURES And InSTALLATIon The„XAP-1040„high„powered„access„point„is„designed„for„optimal„performance„as„ well„as„for„simple„and„efficient„installation„and„setup.„It„implements„Luxul’ s „circular„ polarized„directional„antenna„technology„and„is„packaged„for„installation„outdoors„ on„a„wall„or„pole.„Because„the„signal„generated„by„the„XAP-1040„is„directional„in„ nature,„the„unit„should„be„placed„in„a„location„that„allows„the„antenna„face„to„be„ “pointed”„towards„the„desired„coverage„area.„ 4.1 Front View For„maximum„weather„resistance,„the„XAP-1040„has„no„external„LED„indicators.„The„ front„consists„simply„of„the„access„point„cover„with„the„Luxul„icon„that„indicates„ proper„top/bottom„installation„orientation„of„the„access„point. © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 9: Rear View

    User Guide XAP-1040 Front View 4.2 Rear View The„rear„of„the„XAP-1040„provides„various„mounting„options.„It„is„designed„to„ mount„optimally„to„a„wall„or„pole„using„the„included„mounting„bracket„and„ hardware.„ XAP-1040 Rear View 4.3 Bottom View The„bottom„of„the„XAP-1040„provides„one„RJ-45„connection„that„is„used„to„deliver„ both„power„and„data„to„the„access„point.„When„installation„is„complete,„a„weather„ resistant„RJ-45„connector„gland„will„cover„the„RJ-45„connection.„ luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 10: Inside View

    XAP-1040 Bottom View 4.4 Inside View For„maximum„weather„resistance,„all„System„LEDs„and„the„Reset„button„are„located„ internally.„Unless„it„becomes„necessary„to„do„so,„opening„the„XAP-1040„is„not„ suggested.„Note„that„there„are„no„user„serviceable„parts.„There„is„also„a„metal„insert„ for„grounding„power. For„troubleshooting,„functional„validation„or„system„Reset,„you„will„need„to„open„ the„XAP-1040.„To„do„so,„remove„the„4„screws„at„the„back„of„the„unit.„After„doing„so,„ carefully„lift„the„base„up„and„to„the„right„as„demonstrated„below:„ View of XAP-1040 Opened CAUTION:„Before„removing„the„cover„and/or„attempting„to„service„ the„XAP-1040,„be„sure„to„unplug„all„cables„and„dismount„the„device.„ „ Use„caution„to„see„that„no„external„elements„are„introduced„inside„the„ enclosure„and„that„reasonable„precautions„are„taken„to„minimize„static„ and„electromagnetic„contamination„of„the„electronic„components.„Avoid„ touching„any„of„the„internal„electronics,„except„in„the„case„of„a„Reset.„ © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
  • Page 11 With„the„base„lifted„to„the„right,„System„LEDs„and„the„Reset„button„can„be„seen„as„ shown„here:„ Reset Button Reset Button and LED Location Status Indicators: With„the„unit„facing„down„and„the„base„moved„to„the„right„as„shown„above,„the„ XAP-1040„has„four„LEDs,„positioned„horizontally„on„the„bottom,„left„side„of„the„ board.„When„viewed„left„to„right,„LEDs„are„as„follows:„1)„Bridge„Mode„(Green);„2)„ WLAN„Status„(Blue);„3)„LAN„Link/Activity„(Amber);„and„4)„Power„(Green). The„following„table„describes„the„LED„functionality:„ Indicator„Name Description Bridge„Mode Bridge„Mode„is„enabled„ The„AP„is„in„default„“Access„Point”„mode. luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 12: Environmental Requirements

    To„Restore„the„Default„Settings:„With„the„XAP-1040„powered„on,„press„and„hold„ the„Reset„button„for„10„seconds.„When„the„Power„LED„comes„on„again,„release„the„ reset„button.„The„XAP-1040„will„be„set„to„factory„defaults. CAUTION:„„ P ressing„and„holding„the„Reset„button„will„remove„any„ custom„configurations„done„to„the„XAP-1010. „ 4.5 Environmental Requirements Ethernet„cable„to„provide„Power„and„Data„to„the„XAP-1040.„ „ A„computer„supporting„TCP/IP„and„equipped„with„a„Web„browser.„Supported„ „ Web„browser„versions„include„Microsoft„IE„7.0„and„up,„Safari„1.0„and„up,„Mozilla„ Firefox„1.0„and„up,„and„Google„Chrome„5.0„and„up.„The„Web„browser„is„used„to„ configure„the„XAP-1040.„ The„XAP-1040„uses„36-57VDC„power.„The„POE„injector„power„supply„requires„AC„ „ 100V„~„240V,„50Hz„~„60Hz.„ Temperature„of„the„operating„environment:„-4F~131F„(-20C„to„55C).„Be„sure„to„ „ place„the„access„point„away„from„heat„generating„devices.„ © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 13: Hardware Installation

    The XAP-1040 mount assembles as show above. The u-bolts may be removed and the plate may be mounted directly to a wall using your hardware. luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...
  • Page 14 NOTE:„„ C ategory-5,„super„Category-5„or„Category-6„unshielded„twisted„ pair„(CAT5/CAT5e/CAT6„UTP)„cables„can„be„used.„For„best„ results,„it„is„recommended„that„Category-6„shielded„twisted„pair„ be„used„to„ensure„stable„data„transmission„at„highest„data„rates.„ „ Once„the„RJ45„Connector„Gland„has„been„assembled„and„the„Ethernet„Cable„has„ been„terminated,„the„cable„can„now„be„plugged„into„the„XAP-1040.„You„can„now„at- tach„the„RJ-45„Connector„Gland„by„placing„it„over„the„cable„connector„and„turning„ it„clockwise„until„it„is„firmly„secured.„At„this„time,„also„tighten„the„gland„around„the„ cable„by„turning„it„clockwise„and„thus„creating„a„water-tight„seal.„ 4.6.4 Connecting to the Power Source The„XAP-1040„is„POE„ready„and„supports„Legacy„(48v„1a),„802.3af,„and„802.3at„POE„ injectors.„A„POE„injector„kit,„including„power„supply„and„noise„suppressor„are„ included„with„the„device.„To„apply„power,„simply„connect„the„opposite„end„of„the„ Ethernet„cable„to„which„the„access„point„is„already„connected„to„the„provided„POE„ injector„or„other„POE„switch„or„injector.„An„Ethernet„cable„length„of„up„to„300„feet„ can„be„used.„DO„NOT„yet„apply„power„to„the„POE„injector„or„switch.„ © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
  • Page 15 The POE Injector Sends Power and Signal Over One Ethernet Cable 4.6.6 Applying Power Once„the„Ethernet„cables„have„been„properly„connected,„connect„the„power„sup- ply„to„the„POE„injector„and„plug„it„in„to„a„standard„AC„power„outlet.„Or,„if„plugging„ into„a„POE„switch,„turn„the„switch„(or„appropriate„port)„on.„The„network„source„ device„can„also„now„be„powered„back„on.„ NOTE:„„ I f„your„Internet„source„(Router„or„Switch)„is„a„POE„enabled„device„ and„connected„via„POE,„it„can„be„plugged„directly„into„the„access„ point„without„the„need„to„run„a„separate„POE„injector. „ luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 16: Configuration

    User Guide 5 ConFIGURATIon 5.1 Login The„XAP-1040„is„not„equipped„with„internal„DHCP„server.„If„connected„to„the„Luxul„ XBR-2300„Enterprise„Dual-WAN„Router,„configuration„will„be„automatic.„Otherwise,„ the„IP„address„of„the„computer„for„login„and„configuration„will„need„to„be„manually„ configured.„The„table„below„lists„the„default„parameters„of„the„XAP-1040.„ Parameter Default„Value Default„IP„address 192.168.0.14 Default„user„name„ admin Default„password admin Login„to„the„XAP-1040„Wireless„Access„Point„with„the„following„steps:„ a.„a.„Be„sure„the„XAP-1040„is„properly„installed„and„powered„on„ b.„b.„Open„your„Web„Browser,„and„enter„http://192.168.0.14.„ The„login„window„appears„as„shown„below: c.„e.„Enter„the„user„name„and„password„(default„user„name„is„”admin”„and„default„ password„is„“admin”),„and„then„click„“OK”„to„login„to„the„Quick„Setup„window. © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 17: Quick Setup

    Quick„Setup:„For„most„installations,„it„is„expected„that„the„Quick„Setup„page„will„ be„sufficient„to„optimally„configure„and„deploy„the„XAP-1040„Wi-Fi„network.„The„ Quick„Setup„page„consists„of„the„following: DHCP Client:„Enabled„or„Disabled.„DHCP„(Dynamic„Host„Configuration„Protocol)„ „ is„used„to„automatically„assign„an„IP„Addresses„to„a„device„on„the„network.„If„ DHCP„is„enabled„on„the„Access„Point,„it„will„no„longer„use„the„static„address„set„ by„Luxul„at„time„of„manufacturing„and„will„request„a„dynamic„IP„Address„from„the„ Router„(sometimes„referred„to„as„the„Gateway).„ When„DHCP„is„enabled„on„the„Access„Point,„the„new„IP„address„will„be„needed„ in„order„to„access„the„XenSmart™„web„management„interface.„The„Router„web„ interface„can„be„used„to„look„up„the„IP„address„assigned„to„the„Access„Point.„To„ Enable„DHCP,„click„on„the„drop„down„menu„and„select„Enable.„Select„Apply„and„ then„Reboot„for„the„change„to„take„effect.„ NOTE:„„ D HCP„is„set„as„Disabled„by„default„and„is„the„recommended„ setting„in„order„to„ensure„optimal„communications„with„all„Luxul„ Xen„devices„on„the„network. „ luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...
  • Page 18 Luxul„Xen„XBR-2300„Router. The„Default„Gateway„field„is„the„IP„address„for„this„routing„device.„The„default„ configuration„is„left„blank„or„empty,„allowing„the„Access„Point„to„automatically„ find„the„necessary„route„to„the„Internet.„It„is„recommended„to„leave„this„field„ blank. Network Name (SSID):„Sets„the„name„of„the„Wireless„Network.„Default„name„ „ is„LuxulXen.„It„is„recommended„to„change„the„SSID„from„the„default„name.„The„ SSID„is„case„sensitive„and„can„contain: 2„–„32„alphanumeric„characters „ Spaces „ Special„characters„(i.e.„@#$%&*) „ To„change„the„SSID„of„the„wireless„network,„simply„type„the„desired„name,„click„ Save,„and„then„Reboot„for„the„change„to„take„effect.„ © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
  • Page 19 When„set„to„WPA,„it„is„recommended„that„TKIP„&„AES„be„used.„To„change„the„ Encryption,„click„the„drop„down„menu„and„select„the„desired„encryption„type.„ Once„all„options„are„selected,„click„Save„and„then„Reboot„for„the„change„to„take„ effect. WEP Key:„This„field„only„shows„while„in„WEP„mode„and„sets„the„WEP„key„to„be„ „ used„in„the„network.„WEP„128„bit„keys„require„26„characters.„Allowed„characters„ are„numbers„0-9„and„letters„a-f.„There„are„WEP„key„generators„online„that„can„ automatically„create„a„key.„To„change„the„WEP„Key,„simply„enter„the„26„character„ key„then„click„Save„and„then„Reboot„for„the„change„to„take„effect. WPA Passphrase:„This„sets„the„passphrase„used„by„client„devices„to„connect„to„ „ the„wireless„network„when„using„WPA„Security„Mode.„For„WPA„the„passphrase: Must„be„a„minimum„of„8,„maximum„of„63„characters „ Can„contain„spaces„or„special„characters„(i.e.„@#$%&*) „ To„change„the„WPA„Passphrase,„simply„type„in„the„desired„passphrase,„click„Save,„ then„Reboot„for„the„change„to„take„effect. luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 20: Wireless

    „ „ Administrator Login:„Sets„the„password„for„Administrator„access„to„the„ „ XenSmart™„web„management„interface.„When„connecting„to„the„Access„Point„ through„the„XenSmart™„web„interface,„the„user„is„prompted„for„a„User„ID„(this„is„ always„admin)„and„Password„(the„default„value„is„“admin”).„It„is„HIGHLY„recom- mended„to„change„to„a„secure„password„when„initially„configuring„the„Access„ Point.„To„change„the„password,„simply„enter„the„new„password,„confirm„the„ password,„then„click„Save,„and„then„Reboot„for„the„change„to„take„effect. After„confirming„the„desired„Quick„Setup„configuration„settings,„select„Save„and„ then„Reboot„for„the„settings„to„take„effect.„ 5.3 WIRELESS 5.3.1 Basic Wireless Settings „This„screen„allows„the„modification„of„the„following„basic„ Basic Wireless Settings: settings„for„the„wireless„network: © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
  • Page 21 Channel Width:„Sets„the„width„of„the„802.11n„channel.„Available„widths„are: „ 20MHz„(only„available„for„11g„and„11gnHT20„modes)„ „ 40MHZ„(only„available„for„11gnHT40+„and„11gnHT40-)„ „ 20/40MHz„Auto„(available„for„all„modes) „ The„default„(and„recommended)„setting„is„20/40„MHz„Auto„to„provide„maximum„ performance„to„all„client„devices„and„to„avoid„any„potential„client„issues.„ NOTE:„„ H T40„mode„will„use„two„channels.„For„example,„if„HT40-„is„ selected„and„the„radio„is„using„channel„6,„it„would„also„use„ channel„1.„If„HT40+„is„selected„and„the„radio„is„using„channel„6,„it„ would„also„use„channel„11.„ „ If„making„any„change„to„the„Wireless„Settings,„select„Save„and„then„Reboot„for„the„ settings„to„take„effect.„ luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...
  • Page 22 Network Name (SSID):„Sets„the„name„of„the„Wireless„Network.„If„the„SSID„is„not„ „ set„on„a„profile,„the„name„of„the„network„will„not„be„broadcast.„ NOTE:„„ P rofile„1„is„set„during„Quick„Setup„ „ Security Mode:„Sets„the„wireless„security„encryption„mode. „ Encryption:„This„field„only„shows„while„in„WPA„mode.„It„is„used„to„select„the„ „ encryption„method„WPA„will„use„(default„is„TKIP„&„AES). WEP Key:„This„field„only„shows„while„in„WEP„mode.„Allows„the„input„of„a„128„bit„ „ WEP„key. WPA Passphrase:„Sets„the„passphrase„for„wireless„network„access. „ NOTE:„„ I f„no„Network„Name„(SSID)„is„specified,„the„profile„is„not„active. „ © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 23: Maintenance

    To„change„or„set„a„VLAN„ID,„simply„enter„a„number„from„1-8,„then„click„Save,„and„ then„Reboot„for„the„change„to„take„effect. 5.4 Maintenance 5.4.1 Firmware Upgrade „ Firmware Upgrade:„This„page„allows„for„the„upgrade„of„the„firmware„on„the„XAP- 1040.„To„check„for„firmware„updates,„visit„www.luxul.com/support.„ 1.„ 1.„Go„to„the„Luxul„website„and„download„the„new„version„of„firmware 2.„2.„Click„Browse„to„locate„the„firmware„file„on„your„computer„ 3.„3.„Click„Upgrade„to„perform„the„update„ CAUTION:„„ D o„not„power„off„the„access„point„or„computer„being„used„ during„the„upgrade„or„the„access„point„may„be„damaged. „ luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...
  • Page 24 User Guide 5.4.2 Factory defaults „ Factory Defaults:„Use„this„page„to„return„the„XAP-1040„to„the„original„default„set- tings.„Please„note„that„using„this„feature„will„reset„ALL„values„and„custom„changes„ or„settings„that„have„been„made„to„default„settings.„It„is„recommended„to„backup„ current„settings„prior„to„performing„a„Factory„Default.„To„restore„factory„defaults,„ select„Yes„in„the„drop„down„menu„and„then„select„Save„and„then„Reboot„for„the„ settings„to„take„effect.„ CAUTION:„„ R estoring„default„configuration„will„re-set„all„of„your„ settings„to„factory„defaults.„The„XAP-1040„will„now„have„the„ default„IP„address„192.168.0.10.„For„login,„default„user„name„ will„be„“admin”„and„default„password„will„be„“admin.” „ © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
  • Page 25 User Guide 5.4.3 Backup/Restore „ Backup/Restore:„This„page„is„used„to„create„a„backup„of„the„XAP-1040„configura- tion„and„Restore„the„configuration„at„a„later„time„if„desired.„The„backup„file„can„also„ be„used„to„set„up„multiple„Luxul„Xen„Access„Points„using„the„same„configuration.„ Click„Backup„to„save„the„current„configuration„settings„as„a„file.„To„restore„those„ settings,„click„Browse„and„select„the„backup„file„on„your„Computer,„and„then„click„ Restore. CAUTION:„It„can„take„several„minutes„to„complete„the„restoration.„ To„avoid„errors„during„the„restoration,„do„not„power„off„the„XAP-1040„ or„computer„being„used.„At„the„end„of„restoration,„the„XAP-1040„will„ restart.„ „ luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 26: Status

    5.5 QoS QoS: The„XAP-1040„is„automatically„configured„to„take„advantage„of„Wireless„ Multi-Media„(WMM)„extensions.„This„means„that„any„packets„from„devices„tagged„ with„WMM„will„be„given„top„priority.„There„are„4„priority„levels,„from„highest„to„ lowest: 1.„ Voice 2.„Video 3.„Background 4.„Best„Effort 5.6 Status 5.6.1 Basic Status „ Basic Status: This„page„displays„basic„setup„information„of„the„configuration„and„ status„of„the„AP„including:„Firmware„Version,„Hardware„Model,„Uptime,„Connection„ Type,„IP„Address,„Subnet„Mask,„Default„Gateway,„LAN„MAC„Address,„Wireless„ Mode,„Wireless„MAC„Address,„Network„Name„(SSID),„Channel„Width,„Channel,„and„ type„of„Security © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
  • Page 27 User Guide 5.6.2 Connected Clients „ Connected Clients: This„page„displays„the„MAC„Address,„Speed„and„Signal„Strength„ of„all„currently„attached„wireless„devices. luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 28: Regulatory Compliance

    Safety in Hospitals:„Wireless„devices„transmit„radio„frequency„energy„and„may„ affect„medical„electrical„equipment.„When„installed„adjacent„to„other„equipment,„ it„is„advised„to„verify„that„the„adjacent„equipment„is„not„adversely„affected. 6.2 RF Exposure Guidelines Safety Information:„The„device„complies„with„internationally„recognized„stan- dards„covering„human„exposure„to„electromagnetic„fields„from„radio„devices. Warning: Exposure to Radio Frequency (RF) Radiation: The„radiated„output„of„this„device„is„below„the„FCC„radio„frequency„exposure„ limits.„Nevertheless,„the„device„should„be„used„in„such„a„manner„that„the„potential„ for„human„contact„during„normal„operation„is„minimized. The„end„user„must„avoid„any„extended„human„RF„exposure„directly„in„front„of„ „ the„device,„up„to„a„distance„of„20cm,„when„unit„is„on. © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 29: Radio Frequency Interference Requirements-Fcc

    6.3 Radio Frequency Interference Requirements—FCC This„equipment„has„been„tested„and„found„to„comply„with„the„limits„for„a„Class„ B„digital„device,„pursuant„to„Part„15„of„the„FCC„rules.„These„limits„are„designed„to„ provide„reasonable„protection„against„harmful„interference„in„a„residential„instal- lation.„This„equipment„generates,„uses„and„can„radiate„radio„frequency„energy„and,„ if„not„installed„and„used„in„accordance„with„the„instructions,„may„cause„harmful„ interference„to„radio„communications.„However„there„is„no„guarantee„that„interfer- ence„will„not„occur„in„a„particular„installation.„If„this„equipment„does„cause„harmful„ interference„to„radio„or„television„reception,„which„can„be„determined„by„turning„ the„equipment„off„and„on,„the„user„is„encouraged„to„try„to„correct„the„interference„ by„one„or„more„of„the„following„measures: Reorient„or„relocate„the„receiving„antenna „ Increase„the„separation„between„the„equipment„and„receiver „ Connect„the„equipment„into„an„outlet„on„a„circuit„different„from„that„to„which„ „ the„receiver„is„connected Consult„the„dealer„or„an„experienced„radio/TV„technician„for„help. „ luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...

  • Page 30: Radio Transmitters (Part 15)

    6.4 Radio Transmitters (Part 15) This„device„complies„with„Part„15„of„the„FCC„Rules.„Operation„is„subject„to„the„ following„two„conditions:„(1)„this„device„may„not„cause„harmful„interference,„and„(2)„ this„device„must„accept„any„interference„received,„including„interference„that„may„ cause„undesired„operation. 6.5 Industry Canada (RSS-Gen Issue 2) This„device„complies„with„Industry„Canada„licence-exempt„RSS„standard(s).„ Operation„is„subject„to„the„following„two„conditions:„(1)„this„device„may„not„cause„ interference,„and„(2)„this„device„must„accept„any„interference,„including„interfer- ence„that„may„cause„undesired„operation„of„the„device. Le„présent„appareil„est„conforme„aux„CNR„d’Industrie„Canada„applicables„aux„ appareils„radio„exempts„de„licence.„L’exploitation„est„autorisée„aux„deux„conditions„ suivantes„:„(1)„l’appareil„ne„doit„pas„produire„de„brouillage,„et„(2)„l’utilisateur„de„ l’appareil„doit„accepter„tout„brouillage„radioélectrique„subi,„même„si„le„brouillage„ est„susceptible„d’en„compromettre„le„fonctionnement. This„Class„B„digital„apparatus„complies„with„Canadian„ICES-003. Cet„appareil„numérique„de„la„classe„B„est„conforme„à„la„norme„NMB-003„du„ Canada. © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

  • Page 31: Appendix 1: Technical Support

    To check for firmware updates visit www.luxul.com/downloads Technical Support „ Tel: (801)„822-5450„ Email:„support@luxul.com Contact Information: Address: Luxul„Corporation„ 357„South„670„West,„Suite„160„„ Lindon„UT,„84042„ Tel:„(801)„822-5450 Technical Support:„support@luxul.com luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460...
  • Page 32 User Guide © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

Table of Contents