Gas Instructions; Purchase A Full Cylinder Of Gas From Your Gas Dealer; Connecting The Liquid Propane Cylinder - Weber Spirit E-210 Owner's Manual

6
CAUTION: Do not use oven cleaner, abrasive cleansers
(kitchen cleansers) cleaners that contain citrus products, or
abrasive cleaning pads on barbecue or cart surfaces.
Slide out Bottom tray - Remove excess grease, then wash with warm soapy water,
then rinse.
Flavorizer ® bars and Cooking Grates - Clean with a suitable brass bristle brush. As
needed, remove from grill and wash with warm soapy water, then rinse with water.
Catch pan - Disposable foil trays are available, or you can line the catch pan with
aluminium foil. To clean the catch pan, wash with warm soapy water, then rinse.
Inside cooking module - Brush any debris off burner tubes. DO NOT ENLARGE
BURNER PORTS (OPENINGS). Wash inside of cooking box with warm soapy water
and a water rinse.
Inside Lid - While lid is warm, wipe inside with paper towel to prevent grease build-up.
Flaking built-up grease resembles paint fl akes.
Stainless steel surfaces - Preserve Your Stainless Steel - Your grill or its cabinet,
lid, control panel and shelves may be made from stainless steel. In order to keep the
stainless steel looking its best is easy. Simply clean it with soap and water, rinse with
clean water and wipe dry. A non-metallic brush can be used for stubborn stains.
IMPORTANT: Do not use wire brushes or abrasive cleaners
on the stainless steel surfaces of your grill, as this will leave
scratches.

PURCHASE A FULL CYLINDER OF GAS FROM YOUR GAS DEALER

The cylinder must always be installed, transported and stored in an upright position.
Never allow the cylinder to drop or be handled carelessly. Never store cylinder where
temperatures can exceed 51° C (too hot to hold by hand). For example, do not leave the
cylinder in your car on hot days. (See Section "Safe handling tips for LP gas".)

CONNECTING THE LIQUID PROPANE CYLINDER

Warning: Make sure that the LP cylinder valve is closed.
Close by turning valve clockwise.
Do not use an open fl ame to check for gas leaks. Be sure
there are no sparks or open fl ames in the area while you
check for leaks. Sparks or fl ames will result in a fi re or
explosion that can cause serious bodily injury or death, and
damage to property.
You will need: LP cylinder, a soap and water solution and a rag or brush to apply it.
1) Connect LP cylinder.
Some regulators push on to connect, and pull off to disconnect, others have a nut that
has a left-hand thread that connects to the cylinder valve. Follow specifi c regulator
connection instructions.
A1) Screw regulator fi tting onto tank turning counter-clockwise. Position the
regulator so that the vent hole (a) faces down.
B1) Make sure regulator lever (b) is in the down/off position. Push regulator
down on tank valve until regulator snaps into position.
C1) Make sure regulator leveris in the off position. Slide the collar of the
regulator up (1). Push the regulator down onto the tank valve and
maintain pressure. Slide collar closed (2). If regulator does not lock,
repeat procedure.
2) Mix soap and water.
3) Turn on the cylinder valve.
A2) Turn cylinder valve clockwise.
B2) Move regulator lever counter-clockwise to the ON position.
C2) Move regulator lever to the ON position.
4) Check for leaks by wetting the fi tting with the soap and water solution and watching
for bubbles. If bubbles form, or if a bubble grows, there is a leak. If there is a leak,
turn off the gas and tighten the fi tting. Turn the gas back on and recheck with
the soap and water solution. If leak does not stop, contact the Customer Service
Representative in your area using the contact information on our website. Log onto
www.weber.com ®
5) When leak checking is complete, turn gas supply OFF at the source and rinse
connections with water.
GENERAL INSTRUCTIONS

GAS INSTRUCTIONS

DANGER
IMPORTANT: When cleaning surfaces, be sure to rub/wipe
in the direction of the grain to preserve the look of your
stainless steel.
Thermoset surfaces - Wash with a soft cloth and a soap and water solution.
Do not use cleaners that contain acid, mineral spirits or xylene. Rinse well after
cleaning.
Thermoset surfaces are not to be used as cutting boards.
A1
a)
B1
b)
C1
1.
A2
B2
C2
2.
WWW.WEBER.COM
®