General Information; Operating Limits And Technical Characteristics - Culligan Aqua-Cleer MFP 4-44-MD 400 User's & Technical Manual

GENERAL INFORMATION

The Aqua-Cleer MFP 4-44 MD MD is designed to produce very pure
water for hemodialysis use in conjunction with artificial kidneys; it must
therefore be fed with water to be treated, having characteristics at least
suitable for potable use and treated through a prefiltration process
specially developed and created by Culligan, on the basis of appropriate
chemical analyses.
For the quality of product water, the Aqua-Cleer MFP 4-44 MD is
compatible with all artificial kidneys which, for the qualitative
characteristics of the inlet water, adopt AAMI standards. For the quantity
of product water it is compatible with all artificial kidneys which, overall,
are able to receive an equivalent water flow.
Due to its design, the Aqua-Cleer MFP 4-44 MD can only be used for
hospital dialysis by medical and/or auxiliary medical personnel.
OPERATING LIMITS AND TECHNICAL
CHARACTERISTICS
OPERATING ENVIRONMENT
THE AQUA-CLEER MFP 4-44 MD IS DESIGNED
FOR USE
ENVIRONMENT
ATTENTION
MUST THEREFORE
EQUIPMENT
ENVIRONMENT
WHENEVER
EQUIPMENT
AQUA-CLEER.
THE TABLES
ELECTROMAGNETIC CHARACTERISTICS THE
ENVIRONMENTS MUST COMPLY WITH FOR
CORRECT OPERATION OF THE MFP 4-44 MD.
ALSO, PORTABLE
COMMUNICATION EQUIPMENT CAN AFFECT
THE OPERATION OF THE AQUA-CLEER MFP 4-
44 MD.
OVERALL DIMENSIONS
- Width:
- Depth:
- Total height:
- Shipping weight:
NEVER PLACE ANYTHING ON THE EQUIPMENT
OR PARTS OF IT.
ATTENTION
CHARACTERISTICS OF WATER TO BE TREATED (permissible
values)
THE AQUA CLEER MFP 4-44 MD IS DESIGNED
TO PRODUCE VERY PURE WATER; IT MUST
THEREFORE BE FED WITH RAW WATER,
ATTENTION
WHOSE CHARACTERISTICS (NOT SPECIFIED
BELOW) ARE AT LEAST THOSE MAKING IT
SUITABLE FOR POTABLE USE.
- Max. salinity Aqua-Cleer MFP 4-44 MD model from 400 to 1600: 3000
mg/l (= TDS in ppm)
- Max. salinity Aqua-Cleer MFP 4-44 MD model from 2200 to 3300:
1500 mg/l (= TDS in ppm)
- Temporary hardness:
- S.D.I.:
- pH:
- Chlorine:
- Iron:
M006-06 – Rev. 01 – 05/2012
IN THE ELECTROMAGNETIC
GIVEN BELOW; THE
ENSURE THAT
IS USED IN SUCH
AND CONSIDER
INTENDING TO INSTALL
IN CONJUNCTION WITH
SECTION GIVES
AND MOBILE
see Table 1
see Table 1
see Table 1
see Table 1
 35°f
 3
7  1
 0.2 ppm
 0.1 ppm
Aqua-Cleer MFP4-44 - MD – User
- Manganese:
Calcium Sulfate: concentration in reject water below the solubility
-
limit
- Calcium Carbonate: Langelier index negative in reject water
Silica: concentration in reject water below the solubility limit.
-
N.B.:
- Limit water temperature:
ATTENTION
- Feed water pressure:
- Available feed flow rate:
CHARACTERISTICS OF TREATED WATER INTENDED FOR THE
USER (SERVICE)
USER
THE N.B.:
AN
THIS
NEW
THE
THE
- Flow rate in normal operation:
- Removal of salinity:
.
- Removal of organic matter
RADIO
with molecular weight  200:
- Removal of bacteria and pyrogens:
CHARACTERISTICS OF WATER TO BE SENT TO DRAIN
N.B.:
- Max. flow rate:
CHARACTERISTICS OF EQUIPMENT PLUMBING CONNECTIONS
(Figure 1)
The following plumbing connection fittings are arranged on the back
of the system:
- INLET (
FEED INLET
Raw water inlet:
PRODUCT (
-
Outlet for osmosed water intended for user (service):
DRAIN (
-
Drain water outlet:
EQUIPMENT ELECTRICAL CHARACTERISTICS
- Power supply:
Max. input:
-
- Absorption:
- Protection rating:
Calcium Sulfate, Calcium Carbonate and Silica:
the limits specified refer to the need to prevent
encrustant precipitation.
AT TEMPERATURES BELOW OR ABOVE THE
FIXED LIMITS THE
UNDERGO PERMANENT PHYSICAL DAMAGE
The user treated water flow rate parameter is
obtained as a function of various parameters:
temperature, operating pressure and recovery
ratio are the main ones.
The flow rates given above in the table are
obtained at a water temperature of approx. 20°C,
with a pressure of approx. 261 psi and 200 psi
(18 and 14 bar) according to the models,
recovery ratio of 75% and new osmosis module.
The drain water flow rate parameter is also
obtained as a function of various parameters:
temperature, operating pressure and recovery
ratio are the main ones:
The above flow rates are obtained at a water
temperature of approx. 10°C, with a pressure of
approx. 200 or 261 psi (14 or 18 bar) according
to the models, recovery ratio of 45% and no
longer new osmosis module.
)
)
PRODUCT OUTLET
)
REJECT OUTLET
see Table 1
 0.05 ppm
535°C
MEMBRANES MAY
min. 29 psi (2 bar)
max. 43 psi (3 bar)
see Table 1
see Table 1
~ 96%
~100 %
~99%
see Table 1
1"G female
¾"G female
¾"G female
see Table 1
see Table 1
IP 54
3