Table of Contents
Advertisement
Command/response table for special function SIS commands
The syntax for setting a special function is __ *
a function's setting, use __#, where __ is the function number. In the following table the values of the
are different for each command/function. These values are given below the tables.
Command
RGB delay
Set RGB delay
View RGB delay
Mic talk-over threshold
Adjust talk-over threshold
Increment threshold
Decrement threshold
View Mic talk-over threshold
Program audio ducking level in talk-over mode
Adjust audio ducking level
Increment level
Decrement level
View audio ducking level
Lineout mode
Set lineout to variable
Set lineout to fixed
Set lineout to independent
View lineout mode
Audio output mode
Set audio output mode to dual
mono
Set output mode to stereo
High pass filter mode
Set high pass filter mode off
Set high pass filter mode on
Loudness control
Set loudness off
Set loudness on
View loudness control setting
Power amp gain/attenuation
Set attenuation (-dB)
View input gain
Paging sensor delay
Set paging sensor delay
View paging sensor delay
X@
= Status: 1 = dual mono, 2 = stereo
N
X#
= Status: 0 = off/disable (default), 1 = on/enable
X1)
= Power amp gain, -10 through +10 dB (default = 0)
X1@
= Power amp attenuation, 0 -20, (+/-10 dB in 1 dB steps)
X2@
= RGB delay (0 to 5 seconds), in 0.5 second intervals: 0 = 0 seconds, 1 = 0.5 seconds....10 = 5.0 seconds.
X2%
= Mic talk-over threshold range: 0 to 15 (default = 6)
X2^
= Program ducking level: 0 to 30 (default = 15)
X2&
= Lineout status: 1= variable, 2 = fixed, 3 = independent (separate mono Left channel fixed and mono right
channel variable)
X2(
= Paging delay, in 1 second steps, 0-8, (default = 0, disabled)
#, where __ is the function number and
X?
ASCII command
Response
(host to processor)
(processor to host)
X2@
3*
#
RGBDly*
3#
RGBDly*
X2%
X2%]
2*
#
Thr
X2%]
+*2#
Thr
X2%]
-*2#
Thr
X2%]
2#
Thr
X2^
X2^]
58*
#
Adl
X2^]
+*58#
Adl
X2^]
-*58#
Adl
X2^]
58#
Adl
55*1#
LineOut*
55*2#
LineOut*
55*3#
LineOut*
55#
LineOut*
18*1#
PreAmpMod*
18*2#
PreAmpMod*
X#]
79*0#
Hpf*
X#]
79*1#
Hpf*
29*0#
Loudness*
29*1#
Loudness*
29#
Loudness*
X1@
56*
#
AmpLimit*
56#
AmpLimit*
X2(
75*
#
PageDly*
75#
PageDly*
X?
Additional
description
X2@]
Set RGB delay (in seconds).
X2@]
View RGB delay setting .
Set talk-over threshold.
Increase threshold .
Decrease threshold.
View talk-over threshold .
Set audio ducking level.
Increase level .
Decrease level.
View audio ducking setting .
X2&]
Set lineout to variable mode.
X2&]
Set lineout to fixed mode.
X2&]
Set lineout to separate mono
Left channel fixed and mono
Right channel variable.
X2&]
View lineout mode.
X@]
Sets output to dual mono.
X@]
Sets output to stereo .
Turn high pass filter off.
Turn high pass filter to on .
X#]
Turn loudness control off.
X#]
Turn loudness control on .
X#]
Show loudness control setting
X1)]
Set attenuation level.
X1)]
View input gain .
X2(]
Set delay time.
X2(]
View delay time .
PVS 305SA • Serial Communication
is the value. To view
variable
X?
4-9
Advertisement
Table of Contents
