Troubleshooting; Storage; Specifications - Belkin F6C325 User Manual

Troubleshooting

PROBLEM POSSIBLE CAUSE
UPS not on On/off/test/ button not
LED not lit pushed or pushed less
than 1 second
Battery voltage less than
10V
Load less than 20W
at battery mode
UPS always at Power cord loose
battery mode
AC fuse is burned out
Line voltage too high, too
low or black out
Back up time too short Battery not fully charged
The UPS continuously Overload
beeps
RED LED lit Battery failure

Storage

11.0 Storage Conditions
Store the UPS covered and upright in a cool, dry location, with its
battery fully charged. Before storing, charge the UPS for at least 4
hours. Disconnect any cables connected to the computer interface
port to avoid unnecessary drainage of the battery.
11.1 Extended Storage
During extended storage in environments where the ambient
temperature is -15˚C to +30˚C (+5˚F to +86˚F), charge the UPS
battery every 6 months.
During extended storage in environments where the ambient
temperature is +30˚C to +45˚C (+86˚F to +113˚F), charge the UPS
battery every 3 months.
SOLUTION
Press the on/off/test button
more than 1 second
Recharge the UPS at least
4 hours
Normal condition
Replug the power cord
Replace the AC fuse
Normal condition
Recharge the UPS at
least 4 hours
Remove the
noncritical loads
Replace battery
14

Specifications

MODEL
INPUT Capacity
Voltage
Frequency
OUTPUT Voltage
(on battery)
Frequency
(on battery)
Voltage
Regulation
AVR
Transfer Time
PROTECTION AND Spike Protection
FILTERING
EMI/RFI filter
Overload
Protection
Unit Input
10Base-T
Cable Port
Short Circuit
BATTERY Type
Typical
Recharge Time
Protection
Back up Time
PHYSICAL Net Weight
Kg(lbs)
Shipping Weight
Kg(lbs)
Dimension(mm)
WxDxH
Input Inlet
ALARM Battery
Back-Up
Battery Low
Overload
INTERFACE RS232
Interface
CONFORMANCE Safety
Surge
ENVIRONMENT Ambient operation
Audible noise
Storage condition
F6C325 F6C425 F6C525 F6C625
325VA 425VA 525VA 625VA
100V, 110V, 120V, ±25%
50Hz or 60Hz ±5% (auto sensing)
Simulated sine wave at Line Input ±5%
50Hz or 60Hz ±0.5%
AVR automatically increases output voltage
15% above input voltage if -9% to -25% of
nominal. AVR decreases output voltage
13% below input voltage if +9% to
25% of nominal
2-4 milliseconds, including detection time
320 Joules, 2ms
10dB at 15MHz,
50dB at 30MHz
UPS automatic shutdown if overload
exceeds 110% of nominal at 60 second
and 130% at 3 seconds
Fuse for overload and short circuit protection
Network (UTP, RJ45) compatible jacks
(F6C425, F6C525, F6C625)
UPS output cut off immediately or input
fuse protection
Sealed, maintenance-free lead acid
4 hours (to 90% of full capacity)
Automatic self-test and discharge protection,
replace battery indicator
Depending on computer load...
5-17 min. 5-24 min. 5-32 min. 5-41 min.
4.7(10.4) 5.8(12.8) 6.2(13.7) 6.5(14.3)
5.0(11.0) 6.1(13.4) 6.5(14.3) 6.9(15.2)
97 260 135 97x320x135
x x
IEC 320 power inlet
Slow beeping sound (about 0.47Hz)
Rapid beeping sound (about 1.824Hz)
Continuous beeping sound
Bi-directional communication port
(F6C425, F6C525, F6C625)
cUL, TUV, CE, meet FCC
Meet IEEE 587 standard
6,000 meters max. elevation, 0-95% humidity
non-condensing, 0-48˚C
<40dBA (1 meter from surface)
15000 meters max. elevation
15