6 amp reciprocating saw with rotating handle (16 pages)
Summary of Contents for Chicago Electric 02811
Page 1
7-1/2 INCH - 24 VDC CORDLESS 7-1/2 INCH - 24 VDC CORDLESS 7-1/2 INCH - 24 VDC CORDLESS 7-1/2 INCH - 24 VDC CORDLESS 02811 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com ®...
Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. SKU 02811 Page 2 2811.p65...
Page 3
17. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. SKU 02811 Page 3 2811.p65 10/10/03, 9:59 AM...
Properly recycle or dispose of Ni-Cd battery when it no longer recharges. Do not throw the battery in a fire. Contact your local hazardous waste disposal authority for proper disposal. Note: Performance of this tool may vary depending on variations in battery charge. SKU 02811 Page 4 REV 10/03 2811.p65...
Charge the Battery only in room tempera- ture, and only if the Battery is cool to the touch. Charge the Battery before it is com- pletely discharged. SKU 02811 Page 5 2811.p65 10/10/03, 9:59 AM...
(not supplied) to the saw’s metal Fence (55). Cut a 1/2 inch thick piece of wood to match the height and length of the metal Fence. SKU 02811 Page 6 2811.p65 10/10/03, 9:59 AM...
Page 7
If making miter cuts, loosen the Table Lock Screws (52), and adjust the Saw Blade to the desired angle ranging from 0 to 45 degrees (left or right). When adjusted, tighten the Table Lock Screws (52). SKU 02811 Page 7 2811.p65...
Page 8
Place a wrench on the Screw (69) and turn clockwise until the Screw, Washer, and Blade Press Board (70) can be removed. Cutting Arm Screw (87) Guard (89) Screw (85) Guard Stand (84) Blade Press Board (70) Screw (69) SKU 02811 Page 8 2811.p65 10/10/03, 9:59 AM...
Using a screwdriver, remove the Brush Holder Rear Cover (35) and Brush (34) from the Rear Cover (28). Refer to the Assembly Drawing. Brush Holder Rear Cover (35) and Brush (34) Rear Cover (28) Brush Holder Rear Cover (35) and Brush (34) SKU 02811 Page 9 2811.p65 10/10/03, 9:59 AM...
Page 10
Loosen the Hex Screw counterclockwise to lower the Saw Blade slightly. Retighten Hex Nut. Bevel Stop to 90 Degrees Position saw bevel stop at 90 degrees and loosen Bevel Angle Screw (1). SKU 02811 Page 10 2811.p65 10/10/03, 9:59 AM...
Page 11
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 02811 Page 11 2811.p65...
Parts List NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 02811 Page 12 2811.p65 10/10/03, 9:59 AM...